• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.164-170
• /
• 2016

A proposed pneumatic cylinder-driven roll feeder and an air press were designed to be operated automatically by a PLC. The accuracy of the intermittent feed pitch of the roll feeder was evaluated by measuring lengths of cut-offs of a strip stock by a digimatic vernier caliper. At each predetermined feed pitch, the proposed roll feeder was tested 100 times by varying the feed/cut intervals as 2.0/1.5, 3.0/2.0, and 3.5/2.5 s as test sets. The lengths of the cutoffs of the strip stock ranged from 9.89-10.34, 12.1-12.65, and 15.21-15.67 mm at the predetermined 10, 12, and 15 mm feed pitch, respectively, among the total of 300 samples in each feed pitch, regardless of the feed/shear interval. Therefore, the feed/cut interval at each selected feed pitch was found to have no effect on the accuracy of the intermittent advancing of the strip stock.

• 한국생산제조학회지
• /
• 제19권3호
• /
• pp.353-358
• /
• 2010

This research introduces a new and improved design for a pneumatic cylinder driven roll feeder wherein each of the principal rotating feeder parts is configured so as to have feeding accuracy and to be low manufacturing cost. The feed pitch accuracy of the proposed roll feeder was evaluated by measuring lengths of cut offs of the strip stock with a shear attached to an air press. The air press was designed, manufactured, and mounted on the same table of the proposed roll feeder such that the strip stock maintained horizontal plane until the strip stock entered into the shear. The proposed roll feeder and the air press were designed to be operated automatically by a PLC employed controller. The feed pitch accuracy of the proposed roll feeder was analyzed by setting the pitch as 10, 12.5, and 15mm. At each predetermined feed pitch, the proposed roll feeder was tested 300 times as one test set and replicated three times. The average lengths of the cut offs of the strip stock ranged from 9.98 to 10.13mm, from 12.42 to 12.57mm, and from 14.96 to 15.06mm at the predetermined 10, 12.5, and 15mm feed pitch, respectively, among the total of 900 samples of each feed pitch. Main cause of variation of the length of the cut off of the strip stock fed by the proposed roll feeder was considered to be fluctuation of the air press during recompressing period of the air compressor to pressurize the air in the air tank. The largest difference between the maximum and the minimum length of the cut off was appeared while the air compressor recompressing the air. The air compressor used for this study restricted the air delivered to the proposed roll feeder while it was still running. Thus, this air delivery restriction problem should be improved by stabilizing the air press while the proposed roll feeder is running.

• 한국산림과학회지
• /
• 제97권2호
• /
• pp.181-186
• /
• 2008

Even small changes in phosphorus concentrations in stream water could cause eutrophication because of very low level of phosphorus concentrations in natural waters. I investigated the impact of strip cut and clear cut on phosphorus concentrations in stream water at the Hubbard Brook Experimental Forest and investigated stream water phosphorus concentrations as a function of flow rate and season (as well as cutting history). Mean phosphate concentrations in the control (undisturbed forest) increased $1.9{\mu}g\;L^{-1}\;to\;2.6{\mu}g\;L^{-1}$, while strip cut treatment increased phosphate concentrations in stream water $2.2{\mu}g\;L^{-1}\;to\;3.7{\mu}g\;L^{-1}$ during the same period. There was no significant effect of clear cut treatment on phosphate concentrations in stream water. No relationships were found between discharge rate and phosphate concentrations, but the magnitude of fluctuation were increased during two decades in undisturbed forest: $1-5{\mu}g\;L^{-1}$ from 1963 to 1975 and $1-12{\mu}g\;L^{-1}$ from 1983 to 1995. Based on this study, forest harvests with buffer zone will not make a problem by imported phosphate to cause eutrophication in natural water.

• 한국동물생명공학회지
• /
• 제39권2호
• /
• pp.114-120
• /
• 2024

Background: The Hanwoo industry must develop technologies that can increase the production of preferred cuts to match changing consumer trends. In this study, we aimed to estimate the genetic parameters for carcass traits (carcass weight, eye muscle area, back fat thickness, and intramuscular fat) and primal cut traits (tenderloin, loin, strip loin, neck, clod, top round, bottom round, brisket, shank, and rib) in a Hanwoo population to obtain basic data for improving primal cut productivity. Methods: Data from 1,905 Hanwoo steers, including carcass traits and primal cut weights, were collected. Genetic parameters were estimated using REMLF90 in a multi-trait analysis. Results: High heritability was found for carcass weight (0.52) and strip loin yield (0.63). Genetic correlations between carcass weight and primal cut weights ranged from 0.52 to 0.93. Conclusions: This study demonstrates the significant potential for genetic improvement in Hanwoo cattle through selective breeding, particularly for traits with high heritability and genetic correlations. These findings provide crucial insights into optimizing breeding programs to improve Hanwoo cattle production efficiency.

• 대한전자공학회논문지
• /
• 제25권3호
• /
• pp.343-351
• /
• 1988

Planar optical waveguides are fabricated on a Y-cut LiNbO3 single crystal substrate by Ti indiffusion method. From data measured by the bright M-line spectroscopy, refractive index profiles are reconstructed by WKB approximation method. Then, single strip, X-crossing strip, and Y-brinch strip optical waveguides are fabricated on X-cut LiNbO3 single crystal substrate, with waveguide patterns made by the laser beam direct writing method. And their near-field intensity profiles are observed after coupling the light to the waveguide edges.

• Steel and Composite Structures
• /
• 제6권6호
• /
• pp.531-555
• /
• 2006

H-shaped welded steel column members are fabricated by welding together pre-cut flanges and the web. Modern fabricators are increasingly using plasma-cutting technique instead of traditional flame cutting. Different fabrication techniques result in different degrees of geometric imperfections and residual stresses, which can have considerable influence on the strength of steel columns. This paper presents the experimental investigation based temperature profiles, geometric imperfections, and built-in residual stresses in plasma cut-welded H-shaped steel column members and in similar flame cut-welded H-shaped steel columns. Temperature measurements were taken during and immediately after the cutting operations and the welding operations. The geometric imperfections were established at closely spaced grid locations on the original plates, after cutting plates into plate strips, and after welding plate strips into columns. Geometric imperfections associated with plasma cut element and members were found to be less than those of the corresponding elements and members made by flame cutting. The "Method of Section" technique was used to establish the residual stresses in the plate, plate strip, and in the welded columns. Higher residual stress values were observed in flame cut-welded columns. Models for idealized residual stress distributions for plasma cut and flame cut welded sections have been proposed.

• 소성∙가공
• /
• 제17권4호
• /
• pp.272-277
• /
• 2008

A constitutive equation of the electrical steel strip used for a raw material of transformer is proposed. The stress-strain behavior of electrical steel strip is quite different from that of common carbon steel and/or alloy steel. A series of tensile tests were performed with the specimens made from cold rolled strip. Several thicknesses of the strip were produced by a two-high (with upper and lower rolls) cold rolling pilot mill as reduction ratio increases from 10% to 90%. Its initial thickness of the strip was 2.5mm. Tensile specimens are cut out from the cold rolled strips. Mechanical properties of the steel are examined through rolling direction. Ramberg-Osgood model and the proposed equation are combined to describe the total behavior of stress-strain including instability region. The stress-strain curves calculated from the present constitutive equation are compared with those from experimentally obtained at each test condition of reduction ratios of specimen. Results show that the predicted stress-strain curves are in overall in a good agreement with measured ones.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2002년도 춘계 학술발표회 논문집
• /
• pp.409-416
• /
• 2002

기존의 면진 기술을 일반건물에 적용하기 위해서는 낮은 가격과 낮은 무게로 면진 베어링이 제작 및 공급되어야 한다. 이에 본 논문에서는 일반건물에 면진 기술을 적용하기 위한 방법으로 기존의 적층고무 면진 베어링에 철판을 대체하여 섬유로 보강하고, 고무와 섬유의 층으로 구성된 벨트 타입의 면진 베어링을 제안하였다. 또한 제안한 섬유보강 면진 베어링을 설계 및 제작하여 수직실험과 수평실험을 수행하여 그 성능을 검증하였다. 따라서, 스트립형의 면진 베어링이 제작가능하며 일반건물의 필요한 크기로 절단이 가능함을 보였다. 또한 수평 실험 수직 실험을 통해서 기존의 적층고무 면진 베어링을 대체하여 사용할 수 있는 결과를 보였다. 이와 같은 결과를 통해서 일반건물에 낮은 무게와 낮은 가격의 면진 베어링을 공급할 수 있음을 보였다. 이 연구결과로 인해 스트립형의 섬유보강 면진 베어링이 저가건물에 널리 사용될 수 있을 것으로 기대된다.

• 한국지진공학회논문집
• /
• 제6권6호
• /
• pp.1-6
• /
• 2002

기존의 면진 기술을 일반건물에 적용하기 위해서는 낮은 가격과 낮은 무게로 면진 탄성받침 이 제작 및 공급되어야 할 필요가 있다. 이에 본 논문에서는 일반건물에 면진 기술을 적용하기 위한 방법으로 기존의 적층고무 면진 탄성받침에 철판을 대체하여 섬유로 보강하고, 고무와 섬유의 층으로 구성된 스트립형의 면진 탄성받침을 제안하였다. 또한 제안한 섬유보강 면진 탄성받침을 설계 및 제작하여 수직실험과 수평실험을 수행하여 그 성능을 검증하였다. 따라서, 스트립형의 면진 탄성받침이 제작가능하며, 필요한 크기로 절단이 가능함을 보였다. 또한 수평 실험 수직 실험을 통하여 기존의 적층고무 면진 탄성받침을 대체하여 사용할 수 있음을 보였다. 이 연구결과로 인해 스트립형의 섬유보강 면진 탄성받침이 저가건물에 널리 사용될 수 있을 것으로 기대된다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권3호
• /
• pp.290-296
• /
• 2005

The contour method is based on the elastic superposition principle, and relies on deformations that occur when a residually stressed part is cut along a plane. During the cut, the part is constrained at a location along the cut so that deformations are restrained as much as possible. The displacement is applied to an elastic FE model of the half. When plasticity is involved in the relaxation process, the superposition principle is no longer valid, and stress error in the resulting measurement of residual stress would be caused. Residual stress states in a laser peened Ti-6Al-4V strip were taken for the FE simulation.