• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.560-565
• /
• 2001

The objective of the present study is to investigate the characteristics for flow and wall shear stress in the aneurysm which is a local dilatation of the blood vessel. The numerical simulation using the commercial software for the laminar and steady flow were carried out over the diameter ratios(ratio of maximum diameter of aneurysm to the diameter of blood vessel) ranging from 1.5 to 2.5 and Reynolds number ranging from 900 to 1800. It was shown that a recirculating vortex occupied the entire bulge with its core located closer to the distal end of the bulge and the strength of vortex increased with increase of the Reynolds number and diameter ratio. Especially, for the Reynolds number of 1800 and diameter ratio of 2.5, the very weak secondary recirculating flow was produced at the left upper of the aneurysm. The position of a maximum wall shear stress was the distal end of the aneurysm(z=18mm) regardless of the Reynolds number and diameter ratios. But the maximum values of the wall shear stress increased in proportion to the increase of Reynolds number and diameter ratio.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.5
• /
• pp.734-738
• /
• 2006

The present study was conducted to determine the effect of cold stress on broiler performance and ascites susceptibility. Male chicks were obtained from a commercial strain of broiler breeders. The trial was divided into two treatments (control and cold stress groups). Ascites was induced in broiler chickens in the trial by exposing the chickens to low temperature (Ta) and by supplying a pelleted diet. The two experimental treatments consisted of: 1) Control group, $33.3^{\circ}C$ the $1^{st}$ wk, $30.2^{\circ}C$ the $2^{nd}$ wk, and $27.5^{\circ}C$ the $3^{rd}$ wk. 2) Cold stress group, $29.0^{\circ}C$ the $1^{st}$ wk, $26.4^{\circ}C$ the $2^{nd}$ wk, and $23.1^{\circ}C$ the $3^{rd}$ wk. From the end of the $3^{rd}$ wk all broilers were reared to 6 wk of age at a constant temperature of $21^{\circ}C$. There was significant difference in live BW during wk 1 to 5. The control group was consistently the heaviest; however, at 6 wk of age, both groups weighed the same. Body weight gain up to 3 wk was significantly decreased by cold stress. During wk 3 and 6 the chicks in the cold stress group had greater BW gain compared with the chicks in the control group. There were significant differences in mortality due to ascites between the groups. During wk 3 and 6 the cold stress group exhibited the most ascites mortality (9.52%) when compared with the control group (1.90%). At 5 wk of age cold stress condition caused significant changes in packed cell volume (PCV), hemoglobin (Hb) and red blood cell counts (RBC). Right ventricle weight was significantly heavier in the cold stress group than the control. There were also significant differences in right ventricle/total ventricle (RV/TV) ratios at 5 wk. the right ventricle/total ventricle ratios in the cold stress group was higher (0.25) than the control group (0.20). It was concluded that, fast growth and cold temperatures are the primary triggers for ascites during commercial broiler production.

• Steel and Composite Structures
• /
• v.36 no.1
• /
• pp.75-86
• /
• 2020

The grid structures with welded hollow spherical joint (WHSJ) have gained increasing popularity for use in industrial buildings with suspended cranes, and usually welded with steel tube (ST). The fatigue performance of steel tube-welded hollow spherical joint (ST-WHSJ) is however not yet well characterized, and there is little research on fatigue life prediction methods of ST-WHSJ. In this study, based on previous fatigue tests, three series of specimen fatigue data with different design parameters and stress ratios were compared, and two fatigue failure modes were revealed: failure at the weld toe of the ST and the WHSJ respectively. Then, S-N curves of nominal stress were uniformed. Furthermore, a finite element model (FEM) was validated by static test, and was introduced to assess fatigue behavior with the hot spot stress method (HSSM) and the effective notch stress method (ENSM). Both methods could provide conservative predictions, and these two methods had similar results. However, ENSM, especially when using von Mises stress, had a better fit for the series with a non- positive stress ratio. After including the welding residual stress and mean stress, analyses with the local stress method (LSM) and the critical distance method (CDM, including point method and line method) were carried out. It could be seen that the point method of CDM led to more accurate predictions than LSM, and was recommended for series with positive stress ratios.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.197-202
• /
• 2000

A simple numerical procedure is presented to determine the stress intensity factors for crack in a stiffened panel subjected to a uniaxial uniform stress normal to the crack. Two types of stiffened panels are analyzed by the finite element method for various values of crack lengths, stiffness ratios, and stiffener spacings. From the finite element solution, the stress intensity factors were determined by using hybrid extrapolation method. Results are presented in graphical forms for upper mentioned parameters.

• Asian-Australasian Journal of Animal Sciences
• /
• v.12 no.6
• /
• pp.951-955
• /
• 1999

The effects of restricting feed [60% of ad libitum (AL) intake] (FR) or water provided from 0900 h to 1600 h, daily) (WR) or both (FWR) from 14 to 42 days of age on heterophil/lymphocyte (H/L) response and performance in broiler chickens under the hot humid tropical conditions were determined. Feed and/or water limitation retarded growth, but had no adverse effect on overall feed conversion ratio and survivability. The trend for total feed and water consumption was similar to body weight pattern with AL>WR>FR>FWR. The nutritional regimens had significant effect on overall water:feed ratios with FR>(AL=WR)>FWR. Restriction of feed and/or water resulted in marked elevation of H/L ratios. As measured by H/L ratios, the effect of adapting to FR dissipated between 16 to 21 days after the onset of feed restriction. The H/L ratios of WR and FWR birds remained elevated throughout the duration of the experiment.

• Advances in concrete construction
• /
• v.10 no.5
• /
• pp.381-391
• /
• 2020

This study aimed to develop reference materials (RMs) for mortar that can simulate the initial flow characteristics with constant quality over a long period. Through the previous research on the development of RMs for cement paste, the combination of limestone, glycerol, and water was used as the basic matrix for developing RMs for mortar in this study. In addition, glass beads of three particle sizes (0.5, 1.0, and 2.0 mm) and ISO standard sand were selected as tentative candidates to derive fine aggregate substitutes. The mixture of glass beads could simulate the initial flow characteristics of mortar, but under the same mixing ratio, replicates showed an unstable tendency to indicate inconsistent values due to the generation of electrostatic properties between materials and equipment. On the other hand, the mixture using ISO standard Sand not only simulates the constant flow characteristics for a long period of time, but also shows stable results with little error in replicates. Therefore, limestone, glycerol, ISO standard sand, and water were finally determined as components that met the required properties of RMs for mortar. The effect of each component on the flow characteristics of RMs was analyzed. It was found that glycerol increased the cohesion between the particles of standard sand, resulting in a constant increase both in the plastic viscosity and yield stress. Both limestone and standard sand had a dominant effect on the yield stress. The relationships between various mortar mixing ratios and the corresponding mixing ratios of RMs were established. In addition, the results of the verification experiment showed that the rheological properties of the RMs obtained through the relationships correlated with various water/cement ratios and the fine aggregate volume fractions of mortar obtained with same manner. In other words, the RMs for mortar developed in this study can be used as standard samples because they can simulate the initial flow characteristics of mortar of various mixing ratios for a long period without any chemical changes.

• Journal of muscle and joint health
• /
• v.22 no.2
• /
• pp.138-147
• /
• 2015

Purpose: The study was conducted to identify factors influence suicidal ideation among older adults with osteoarthritis. Methods: This study used a cross-sectional design with secondary analysis of the Korean National Health and Nutrition Examination Survey. Data for 174 men and 939 women who aged${\geq}65$, and were diagnosed osteoarthritis from the Korea National Health and Nutrition Examination Survey 2010~2012 were included. Suicidal idea, age, sex, education, marital status, living alone, income, body mass index, smoking and alcohol use, exercise, perceived health status, activity limitation, joint pain and stiffness, depressive mood, and perceived stress were measured. Influencing factors and odds ratios were analyzed using complex sample multivariate logistic regression. Results: In the results, 29.9% of the elderly with osteoporosis had suicidal idea. The adjusted odds ratios (ORs) of suicidal ideation were significantly higher among those over 80 years older (OR=2.88, 95% CI=1.49~5.58), those with depression (OR=4.01, 95% CI=2.66~6.04), and those with high levels of stress (OR=2.76, 95% CI=1.79~4.24). Conclusion: Therefore, older adults with osteoarthritis should be screened for depression and stress to decrease suicidal ideation and prevent suicide attempt.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.9 no.5
• /
• pp.473-483
• /
• 2017

Comprehensive consideration regarding influence mechanisms of initial imperfections on ultimate strength of spherical shells is taken to satisfy requirement of deep-sea structural design. The feasibility of innovative numerical procedure that combines welding simulation and non-linear buckling analysis is verified by a good agreement to experimental and theoretical results. Spherical shells with a series of wall thicknesses to radius ratios are studied. Residual stress and deformations from welding process are investigated separately. Variant influence mechanisms are discovered. Residual stress is demonstrated to be influential to stress field and buckling behavior but not to the ultimate strength. Deformations are proved to have a significant impact on ultimate strength. When central angles are less than critical value, concave magnitudes reduce ultimate strengths linearly. However, deformations with central angles above critical value are of much greater harm. Less imperfection susceptibility is found in spherical shells with larger wall thicknesses to radius ratios.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.10
• /
• pp.77-82
• /
• 2000

The design of the prestressed cold extrusion die with two stress rings has been performed in this study. The cold extrusion has been simulated by the rigid-plastic FEM. The stress analysis of die has been performed for both after shrink fitting and during extrusion by using the elastic FEM and the Lame's equation. According to the variation of interferences and diameter ratios, the maximum effective stress has been evaluated. As results, interferences and diameters were determined by the minimization of the maximum effective stress of die insert. The comparison of the maximum effective stress between the proposed design and the conventional design has been discussed. It was found that the maximum effective stress in the die insert is considerably affected by the stiffness of the first stress ring.

• Journal of the East Asian Society of Dietary Life
• /
• v.8 no.2
• /
• pp.126-136
• /
• 1998

This study was designed to determine the effects of linoleic acid contents and $\omega$ 6/$\omega$3 ratios on the induction of gastric ulcer by water immersion and restraint stress. Sprague-Dawley rats were fed 5diets containing 7% fat(w/w) for 6weeks. These diet groups were Lh, Mh, Hh, Mm, Ml, : 3 different linoleic acid levels(0.3% of energy(L). 3.5(M), 10(H) and 3 different $\omega$6/$\omega$3 ratios (11(1), 33(m), 100(h) with beef tallow, sunflower or fish oil. The Lh group showed a significantly higher ulcer index (UI) than the Mh and Hh groups(p<0.05). At the same linoleic levels, the UI had no significant difference within the $\omega$6/$\omega$3 ratios. The Mh group showed significantly higher (p<0.05) PGE2 and TBX2 content than any other group. Pearson's correlation coeffcients between UI and PGE2 and TBX2 had a negatively significant correlation(p<0.05). Linoleic acid of gastric mucosal phospholipids was reflected by the diet, but was not significantly different. The most significant finding of this study is that not only the absolute amount of linoleic acid, but also the $\omega$6/$\omega$3 ratios are important factors for the prevention of gastric ulcer.