• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.280-283
• /
• 2011

This study investigates the durability of car body and the safety of passenger inside car body in the case of the impact contact at passenger and car body. In case of front impact contact, maximum von Mises equivalent stress and principal stress become 3240.7MPa and 1634MPa respectively at the rear part of car body and the neck of dummy. And maximum total deformation occurred with 14.145mm at the hand of dummy. In case of side impact contact, maximum von Mises equivalent stress and principal stress become 7687.9MPa and 1690.7MPa respectively at the front part of car body and the lap of dummy. And maximum total deformation occurred with 16.414 mm at the foot of dummy. In case of rear impact contact, maximum von Mises equivalent stress and principal stress become 2366.6MPa and 1447MPa respectively at the front part of car body and the neck of dummy. And maximum total deformation occurred with 7.548mm at the rear part of car body. As the maximum von-Mises stress at side impact is shown with more than 700MPa as over two times at front or rear impact the danger of car body is increased. The great possibility of damage is shown at neck and hand of dummy with more than total displacement of 10mm.

• 지질공학
• /
• 제32권4호
• /
• pp.643-659
• /
• 2022

최근 지중저장기술(예, 온실가스 심지층 처분, 인공지열저류층 발전 등)이 활발히 수행됨에 따라, 유체 주입과 저장부지 안정성 사이의 역학적 관계에 관한 정량적 이해의 중요성이 인지되고 있다. 지중 유체 주입은 공극압 및 지중응력 교란과 지층의 역학적 불안정성을 야기할 수 있어, 유체 주입에 대한 다공탄성 수치 모형 구축이 요구된다. 본 연구에서는 순차적인 COMSOL-PyLith-COMSOL 유체 주입-유발지진 다공탄성 수치 모사를 수행한다. 유한요소 상용 소프트웨어인 COMSOL을 이용해 단층에 가해지는 쿨롱 파괴 응력(CFS) 변화를 시간에 따라 추적하였고, CFS 변화량이 임계값(예, 0.1 MPa)을 초과할 경우, 모형의 정보(기하구조, 물성 등)를 유한요소 오픈소스 코드인 PyLith로 이동시키는 알고리즘을 구축했다. PyLith는 단층의 미끄러짐을 모사하고, 미끌림에 의한 변위장을 획득한다. 이후 변위장을 COMSOL로 이동시켜 지진에 의한 응력 및 표면 변위를 계산한다. 수치 모사 결과, 주입 기간 중엔 주입정 근거리에서 큰 변화(공극압, CFS 변화 등)를 보였고, 주입 종류 후에는 잔류 응력이 원거리 영역으로 확산하는 양상이 나타났다. 이는 주입 종료 후 지속적인 모니터링의 필요성을 제안한다. 또한, 단층과 주입층 물성(예, 투수계수, Biot-Willis 계수)에 따른 CFS 변화량 비교는 주입정 위치 선정 시 주입층 및 주변 지층에 대한 물성 파악이 중요함을 의미한다. 단층 미끄러짐 양에 따른 표면 변위 및 이암층에 가해지는 편차응력은 다양한 단층 미끌림 시나리오 설정의 필요성을 지시한다.

• 한국정밀공학회지
• /
• 제20권7호
• /
• pp.208-216
• /
• 2003

In this paper, a two-dimensional electroelastic analysis is performed on a piezoelectric material with an open crack. The approach of Lekhnitskii's complex potential functions is used in the derivation and Bueckner's weight function theory is extended to piezoelectric materials. The stress intensity factors and the electric displacement intensity factor are calculated by the weight function theory.

• 한국해양공학회지
• /
• 제24권3호
• /
• pp.59-63
• /
• 2010

In this paper, an electroelastic analysis is performed on a piezoelectric material with an open crack in anti-plane deformation. Bueckner’s weight function theory is extended to piezoelectric materials in anti-plane deformation. The stress intensity factors and electric displacement intensity factor are calculated by the weight function theory.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.308-313
• /
• 2004

SP test has been confirmed the availability, however the application of SP test is hampered because the relation of stress-strain and load-displacement is not determined definitely. This study suggested an evaluation technique of plastic flow characteristic for X20CrMoV121 steel weldment through inverse analysis using SP test and finite element analysis(FEA). From the result, good agreement was found in load-displacement curves obtained from SP test and FEA. Also, The behavior of load-displacement curve from FEA show a rule that load is increase with increasing K(strength coefficient) and displacement is increase with increasing n(work hardening index). From the inverse analysis, true stress-strain curve could be obtained for each local structure of weldment. And the CGHAZ and WM, which showed lower load- displacement behavior, have smaller work hardening index, while FGHAZ have the largest index.

• Geomechanics and Engineering
• /
• 제16권1호
• /
• pp.97-104
• /
• 2018

The finite difference software Flac3D is used to study the influence of tunnel burial depth, tunnel diameter and lateral pressure coefficient of original rock stress on the stress and deformation of tunnel surrounding rock under sandstone condition. The results show that the maximum shear stress, the radius of the plastic zone and the maximum displacement in the surrounding rock increase with the increase of the diameter of the tunnel. When the lateral pressure coefficient is 1, it is most favorable for surrounding rock and lining structure, with the increase or decrease of lateral pressure coefficient, the maximum principal stress, surrounding displacement and plastic zone range of surrounding rock and lining show a sharp increase trend, the plastic zone on the lining increases with the increase of buried depth.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.127-131
• /
• 2008

This paper deals with the performance evaluation of piezoelectric unimorph actuator. In the unimorph design, the thickness ratio of substrate to piezoelectric material and the elastic modulus ratio of substrate to piezoelectric material are important parameters. There exists only one structural configuration that satisfies the optimal condition among them, and actuators using that configuration exhibit better actuating displacements. Another design parameter is the piezoelectric coefficient which can be improved due to the induced tensile stress and voltages. The application of the tensile stress to the piezoelectric material makes it get higher piezoelectric coefficient and the total displacement performance of the unimorph actuator is improved. Finally, the piezoelectric actuator system with spring elements is fabricated and it shows higher actuating displacement capability.

• 한국농공학회지
• /
• 제36권1호
• /
• pp.83-94
• /
• 1994

The first part of this study dealt with the determination of soil parameters for Lade's double work-hardening model using the raw data obtained from cubical and cylinderal triaxial tests At present, it should be investigated which test can simulated satisfactorily the behavior of soft clayey foundation. In this regard, plate bearing test on the 2-dimentional model foundation(218cm long, 40cm wide, 19&m high) was performed, and finite element analysis carried out to abtain the behavior of the foundation. Settlement, lateral displacement, displacement vector and mode of failure were measured and these values were compared with numerical values in order to validate the numerical program developed by authors. The FEM technique was based on Christain-Boehmer's method, in which the displacement is obtained at each nodal point while stress and pore water pressure at each element.In this research, Biot's equation, which explains was elahorately the phisical meaning of consolidation, was selected, as a governing equation, coupled with Lade's double surface work-hardening constitutive model.

• 한국정밀공학회지
• /
• 제1권1호
• /
• pp.50-58
• /
• 1984

In the present paper are calculated and compared the stresses on the normal tools and the restricted tools which have three various rake angles by Least Square Method. The results obtained are summerized as follows. The tool displacement at rake angle .alpha. = 12 .deg. and .alpha. = 0 .deg. is positive value in the principal cutting direction and negative value in the feed direction. At rake angle .alpha. = -12 .deg. the displacement is negative value in both of directions. The principal stress of the restricted and normal tool is maximum at the tip of the tool, the shear stress is maximum after a certain distance from the tip. The result of FEM and P.E method shows that in the range of rapid decreasing of normal stress of the tool edge, the shear stress is maintaining a certain value. This is due to the friction characteristic of the chip.

• 소음진동
• /
• 제7권1호
• /
• pp.81-89
• /
• 1997

The structural stress and vibration analysis of the rotary screen are investigated. The mechanical properties of the rotary screen, this is, Young's modulus and density of nickel alloy are determined experimentally. The natural vibration characteristics of the rotary screen are evaluated and the displacement, the stress of the rotary screen under the various load conditions are also examined. The radial displacement of the rotary screen is obtained by experiment under various rotating speeds.