• Structural Engineering and Mechanics
• /
• 제25권4호
• /
• pp.365-382
• /
• 2007

A pilot study has been conducted to guide the development of a finite element modeling formulation for the analysis of architectural glass curtain walls under in-plane lateral load simulating earthquake effects. This pilot study is one aspect of ongoing efforts to develop a general prediction model for glass cracking and glass fallout for architectural glass storefront and curtain wall systems during seismic loading. For this study, the ANSYS finite element analysis program was used to develop a model and obtain the stress distribution within an architectural glass panel after presumed seismic movements cause glass-to-frame contact. The analysis was limited to static loading of a dry-glazed glass curtain wall panel. A mock-up of the glass curtain wall considered in the analysis with strain gages mounted at select locations on the glass and the aluminum framing was subjected to static loading. A comparison is made between the finite element analysis predicted strain and the experimentally measured strain at each strain gage location.

• International Journal of Korean Welding Society
• /
• 제3권1호
• /
• pp.51-56
• /
• 2003

It is important to evaluate the fracture initiation behaviors of steel structure. It has been well known that the ductile cracking of steel would be accelerated by triaxial stress state. Recently, the characteristics of critical crack initiation of steels are quantitatively estimated using the two-parameters, that is, equivalent plastic strain and stress triaxiality, criterion. This study is paid to the fundamental clarification of the effect of notch radius, which can elevate plastic constraint due to heterogeneous plastic straining on critical condition to initiate ductile crack using two-parameters. Hense, the crack initiation testing were conducted under static loading using round bar specimens with circumferential notch. To evaluate the stress/strain state in the specimens was used thermal elastic-plastic FE-analysis. The result showed that equivalent plastic strain to initiate ductile crack expressed as a function of stress triaxiality obtained from the homogeneous specimens with circumferential notched under static loading. And it was evaluated that by using this two-parameters criterion, the critical crack initiation of homogeneous specimens under static loading.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.63-68
• /
• 1999

Because misaligned shafts have caused noise, vibration, bearing failures, and stress concentration of coupling part, which decrease the efficiency and life of a shaft system, the proper alignment of shaft system should be monitored continuously in dynamic condition. To solve these problems under dynamic condition, a telemetry system is this study is used to find the condition of the least bending moment, which is known by analyzing the structure and stress induced by misalignment is investigated. The moment derived from two shaft strain at the nearby coupling is measured. The bending strain is measured 5 times for average in static state as well as dynamic state with 100~700 rpm.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 춘계학술대회 논문집
• /
• pp.399-406
• /
• 2000

In this study, using the CRS consolidation tests on reconstituted marine clay, the characteristics of C$\sub$v/, k, e and $\varepsilon$, the anisotropic characteristics of specimen according to the rate of strain were estimated. Also, the validity of the Wissa et al.(1971) consolidation theory on CRS(Constant Rate of Strain) consolidation tests were reviewed. From that results, it was shown that the value of C$\sub$v/, k and u$\sub$b/ was increased as the rate of strain was increased. While the difference of the value( C$\sub$v/, k and u$\sub$b/) between vertically reconstituted specimen and horizontally reconstituted specimen became small as the rate of strain was increased. It is known that k is different due to the hydraulic gradient(i) during the CRS consolidation tests. The subject of this study is to distinguish steady state from transient state in CRS consolidation tests. Consequently, the difference of the value(C$\sub$v/ and k) is higher in case of vertically reconstituted specimen than horizontally reconstituted specimen.

• 터널과지하공간
• /
• 제20권2호
• /
• pp.105-111
• /
• 2010

본 연구에서는 연약지반기초 및 암반사면 거동 계측 도구로서 스파이럴 볼트 변형률계의 적용 가능성을 살펴보고자 한다. 이 변형률계가 지중에 설치되었을 때, 지반에 대한 인발 저항성이 높아 지반 보강용으로 적용될 수 있을 뿐만 아니라, 유연성의 특징을 가지고 있기 때문에 지반의 거동 상태를 파악하는데 유용하게 이용될 수 있다. 연약지반기초에 대한 스파이럴 볼트의 변형률 계측결과, 변형률 측정 초기에는 안정한 상태를 보이다가 400일이 경과한 시점에서는 스파이럴 볼트 변형률계의 윗부분과 중간부분에서 큰 변화가 관찰되었다. 이러한 변화는 동일한 시기에 강수량 증가와 함께 빈번하게 발생한 진도 1~2의 지진에 의한 영향으로 지반이 이완되어 야기한 것으로 분석된다. 암반사면에 대한 스파이럴 볼트의 변형률 계측결과, 측정시작일로부터 50일 동안에 안정한 상태를 보였으며 50~160일 기간에는 매설길이 4.2 m 지점(P6)의 변형률 게이지에서 가장 큰 변형률을 보였다. 그러나 P6 변형률 게이지를 제외한 나머지 게이지는 특이한 변화를 보이지 않았다. 스파이럴 볼트 변형률계의 측정결과를 종합적으로 살펴보면 측정대상인 연약지반기초와 암반사면은 안정적인 것으로 판단된다. 본 연구에서 소개하는 스파이럴 볼트 변형률계는 연약지반기초 및 암반사면 거동의 모니터링과 동시에 대상지반의 보강에 적용될 수 있을 것으로 사료된다.

• 한국해양공학회지
• /
• 제6권1호
• /
• pp.78-86
• /
• 1992

The creep behaviors of 1%Cr-Mo-V and 12%Cr steam turbine rotor steels under static or cyclic load were examined at 600 and $700^{\circ}C$. The relationship between these two kinds of phenomena was studied and the experimental results were summarized as follows: 1) It is confirmed that the cyclic creep strain dependent on time is more available for creep, behavior analysis according to frequency change than that dependent on number of cycles, and the static creep, the special case of cyclic creep with stress ratio of 1 can be also more effectively analyzed by time-dependence. 2) The steady cyclic creep rate vs. the steady static creep rate, increases according to the increase of stress ratio, and this phenomena may occur on occasion of the decrease of the internal stress. 3) The initial strain affects on all the creep properties of the transient region, the steady state region and the rupture time in cyclic creep as well as static creep, and the quantitative relationships among them exist.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.194-197
• /
• 2007

액체로켓 연소기 재생냉각 챔버의 제작에 사용되는 구리합금의 성형한계 곡선을 얻기 위하여 돔 장출 시험과 인장시험을 수행하였다. 성형한계 곡선에 대한 실험적인 연구를 위하여 인장시편을 사용하여 인장-압축 변형률 상태의 데이터를 얻었으며, 인장-인장의 변형률 상태를 얻기 위하여 돔 장출 시험용 시편을 사용한 돔 장출 시험 또한 수행하였다. 시험에 사용한 모든 시편은 제작방법에 따라 종 방향과 횡 방향시편으로 구분하였다. 시험 결과 인장-인장 변형률 상태에서 최대 주 변형률과 부 변형률은 62.3%와 58.6%이며 인장-압축 상태에서는 60.5%와 25.8%로 나타났다.

• 한국정밀공학회지
• /
• 제12권3호
• /
• pp.101-109
• /
• 1995

Axisymmetric and quasi-static finite element analysis of an inflated tire rotating with constant angular velocity and contact to road has been performed. Centrifugal force effect was added to load stiffness matrix and equation of effective material properties were calculated by the Halpin-Tsai formulation. In this report, radial truck/bus tire was analyzed. It was inflated and rotated at speeds up to 140 km/h. Then, contact problem was performed to calculate stress-strain field of tire wiht flat rigid road under the load due to the self-weight of a vehicle. Significant changes of stress-strain field of tire were observed in the finite element analysis. Shear stress, strain and strain energy density were rapidly increased at the dege of #2 belt at freely rotating state. This concentrated stress and strain made belt edge sparation. Under the condition of flat riged road contact, strain energy density of #2 belt, carcass turn-up part were concentrated and bigger values than only freely rotation state. Therefore, dynamic behaivor of tire has to considered as design factors which are affected to belt edge separation and bead breakage.

• Geomechanics and Engineering
• /
• 제34권2호
• /
• pp.197-208
• /
• 2023

Rate-dependent mechanical response of sand, subjected to loading of medium to high strain rate range, is of interest for several civilian and military applications. Such rate-dependent response can vary significantly based on the initial density state of the sand, applied confining pressure, considered strain rate range, drainage condition and sand morphology. A numerical study has been carried out employing a recently proposed visco-plastic constitutive model to explore the rate-dependent mechanical behaviour of Toyoura sand under drained triaxial loading condition. The model parameters have been calibrated using the experimental data on Toyoura sand available in published literature. Under strain rates higher than a reference strain rate, the simulation results are found to be in good agreement with the experimentally observed characteristic shearing behaviour of sand, which includes increased shear strength, pronounced post-peak softening and suppressed compression. The rate-dependent response, subjected to intermediate strain rate range, has further been assessed in terms of enhancement of peak shear strength and peak friction angle over varying initial density and confining pressure. The simulation results indicate that the rate-induced strength increase is highest for the dense state and such strength enhancements remain nearly independent of the applied confinement level.

• Restorative Dentistry and Endodontics
• /
• 제43권4호
• /
• pp.48.1-48.13
• /
• 2018

Objectives: To analyze the influence of thickness and incisal extension of indirect veneers on the stress and strain generated in maxillary canine teeth. Materials and Methods: A 3-dimensional maxillary canine model was validated with an in vitro strain gauge and exported to computer-assisted engineering software. Materials were considered homogeneous, isotropic, and elastic. Each canine tooth was then subjected to a 0.3 and 0.8 mm reduction on the facial surface, in preparations with and without incisal covering, and restored with a lithium disilicate veneer. A 50 N load was applied at $45^{\circ}$ to the long axis of the tooth, on the incisal third of the palatal surface of the crown. Results: The results showed a mean of $218.16{\mu}strain$ of stress in the in vitro experiment, and $210.63{\mu}strain$ in finite element analysis (FEA). The stress concentration on prepared teeth was higher at the palatal root surface, with a mean value of 11.02 MPa and varying less than 3% between the preparation designs. The veneers concentrated higher stresses at the incisal third of the facial surface, with a mean of 3.88 MPa and a 40% increase in less-thick veneers. The incisal cover generated a new stress concentration area, with values over 48.18 MPa. Conclusions: The mathematical model for a maxillary canine tooth was validated using FEA. The thickness (0.3 or 0.8 mm) and the incisal covering showed no difference for the tooth structure. However, the incisal covering was harmful for the veneer, of which the greatest thickness was beneficial.