• Structural Engineering and Mechanics
• /
• 제89권1호
• /
• pp.23-31
• /
• 2024

Ratcheting is the cyclic buildup of inelastic strain on a structure resulting from a combination of primary and secondary cyclic stress. It can lead to excessive plastic deformation, incremental collapse, or fatigue. Ratcheting has been numerically investigated on a cantilever beam, considering the current study's primary and secondary bending loads. In addition, the effect of input frequency on the onset of ratcheting has been investigated. The non-linear dynamic elastic-plastic approach has been utilized. Analogous to Yamashita's bending-bending ratchet diagram, a non-dimensional ratchet diagram with a frequency effect is proposed. The result presents that the secondary stress values fall sequentially with the increase of primary stress values. Moreover, a displacement amplification factor graph is also established to explain the effect of frequency on ratchet occurrence conditions. In terms of frequency effect, it has been observed that the lower frequency (0.25 times the natural frequency) was more detrimental for ratchet occurrence conditions than the higher frequency (2 times the natural frequency) due to the effect of dynamic displacement. Finally, the effect of material modeling of ratcheting behavior on a beam is shown using different hardening coefficients of kinematic hardening material modeling.

• 한국전산구조공학회논문집
• /
• 제34권5호
• /
• pp.271-278
• /
• 2021

편심가새골조(EBF)의 역량설계법에 의하면, 링크가 완전항복 및 변형경화 상태일 때 기둥, 링크외부보, 가새(비소산 부재)는 탄성거동해야 한다. 현행 AISC 341은 역량설계에 필요한 변형도경화계수(SHF)를 1.25로 제시하고 있으나, 실제로 건물이 고층 규모일수록 모든 링크가 이처럼 동등한 수준의 초과강도에 도달할 가능성은 매우 낮아진다. 본 연구에서는 링크의 SHF를 정밀하게 예측하는 방법을 제안함으로써, 역량설계법의 목적을 달성하면서 구조물량을 절감하고자 하였다. 제안한 방법의 효과를 검증하기 위해 선형해석을 2회 수행하여 SHF를 예측하고, 이를 비선형 해석결과와 비교하였다. 다음으로 비선형 해석에 의한 응답을 분석하여 구조물의 한계상태에서 비소산 부재들의 항복 여부를 확인하였다. 그 결과, 본 연구의 방법으로 설계된 구조물은 링크의 SHF를 정확히 예측함으로 인해 물량이 큰 폭으로 절감되었으며, 비소산 부재들도 모두 탄성상태를 만족하는 것으로 나타났다.

• Steel and Composite Structures
• /
• 제21권5호
• /
• pp.1121-1144
• /
• 2016

This paper presents a displacement-based finite element procedure for second-order distributed plasticity analysis of planar steel frames with semi-rigid beam-to-column connections under static loadings. A partially strain-hardening elastic-plastic beam-column element, which directly takes into account geometric nonlinearity, gradual yielding of material, and flexibility of semi-rigid connections, is proposed. The second-order effects and distributed plasticity are considered by dividing the member into several sub-elements and meshing the cross-section into several fibers. A new nonlinear solution procedure based on the combination of the Newton-Raphson equilibrium iterative algorithm and the constant work method for adjusting the incremental load factor is proposed for solving nonlinear equilibrium equations. The nonlinear inelastic behavior predicted by the proposed program compares well with previous studies. Coupling effects of three primary sources of nonlinearity, geometric imperfections, and residual stress are investigated and discussed in this paper.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.313-316
• /
• 2005

In the recent design of high ductile fiber-reinforced cementitious composite ECC, which exhibits tensile strain-hardening behavior in the hardened state, optimizing both processing mechanical properties for specific applications is critical. This study introduced a method to develop useful ECCs in field, which possess the different fluid properties to facilitate diverse types of processing (i.e., self-consolidating or spray processing). Control of rheological modulation was regarded as a key factor to allow the performance of the desired processing, while retaining the ductile material properties. To control the rheological properties of the composite, we first determined basic ECC compositon, which is based on micromechanics and steady-state cracking theory. The stability and consequent viscosity of suspensions were, then, mediated by optimizing dosages of chemical and mineral admixtures. The rheological properties altered by this approach were revealed to be effective in obtaining ECC hardened properties, allowing us to readily achieve the desired function of the fresh ECC.

• 한국건설순환자원학회논문집
• /
• 제7권3호
• /
• pp.279-286
• /
• 2019

본 연구에서는 기준압축강도 180MPa의 강섬유 보강 초고강도 콘크리트(UHSC)의 인장 특성에 관한 실험 연구를 수행하였다. 부피비 1%의 강섬유를 혼입하여 직접인장강도 시편과 3점 하중재하 휨 실험을 위한 프리즘 시편을 제작하였다. 제작된 시편은 균열 유도를 위하여 시편 중앙에 노치를 설정하였으며, 각 평가방법에 따라 실험을 수행하였다. 우선, 콘크리트의 균열 후 거동 특성을 파악하기 위하여 직접인장강도 실험을 수행하여 응력-변형률 곡선을 분석하였으며, 3점 하중재하 휨 실험을 통하여 하중-CMOD 곡선을 얻고, 역해석을 수행하여 응력-변형률 곡선을 분석하였다. 직접인장강도 실험과 3점 하중재하 휨 실험의 인장거동 특성은 유사하게 나타났다. 또한, SC 구조설계지침에서 제시하고 있는 인장응력-변형률 곡선 모델링을 수행하고, 측정값과 예측값의 비교분석을 수행하였다. 재료감소계수가 1.0일 때, 변형률이 0.02일 때까지 예측값은 측정값과 유사하게 나타나지만, 재료감소계수가 0.8일 때, 예측값은 측정값의 최소값에 근접한다. 또한, 변형률이 0.02를 초과하는 구간에서는 SC 구조설계지침에 의한 예측값이 측정값을 과소평가한다.

• 열처리공학회지
• /
• 제24권2호
• /
• pp.92-98
• /
• 2011

The influence of the cooling condition after solution treatment on the high temperature fatigue resistance of 23Cr-26Ni heat resistant steel was investigated. Two different cooling conditions were applied to the steel after solution treatment at $1200^{\circ}C$ for 3 hours. One specimen was water quenched immediately after the solution treatment. The other one was furnace cooled at a rate of $0.5^{\circ}C/min$ down to $750^{\circ}C$ after the solution treatment. Then, both specimens were aged at $750^{\circ}C$ for 5 hours. Under two different heat treatment conditions, the low cycle fatigue (LCF) test was performed at $600^{\circ}C$ and room temperature (RT). Only cyclic hardening continued from the beginning until fracture at all strain amplitudes during LCF at $600^{\circ}C$. This phenomenon was attributed to the increase in the dislocation density due to cyclic deformation, which resulted in the interaction between the newly created dislocations and precipitates. Cyclic hardening followed by saturation and cyclic softening was observed at RT. Cyclic softening was attributed to the dislocation annihilation rate exceeding the dislocation generation rate. Other probable factor for cyclic softening was some cavities formed around grain boundaries after 20 cycles. WQ and FC have a similar LCF behavior at RT and $600^{\circ}C$ as shown in the cyclic stress response curves.

• 대한기계학회논문집A
• /
• 제20권7호
• /
• pp.2246-2256
• /
• 1996

To investigate the effect of material and precess variables on stamping formability of sheet materials, simulations for the cup drawing and the Yoshida buckling test were carried out using ABAQUS, commercial nonlinear finite element analysis code. The various factor effects on stamping formability of sheet materials were analyzed by the designed process according to Taguch's orthogonal array experiment. Cup drawing simulation showed that local neckling was very sensitive to plastic anisotropy parameter of sheet material and friction coefficient between sheet and tool interface. Simulations for the Yoshida buckling test have clarified that buckling behaviour of sheet material was mostly susceptible to yield stress and sheet thickness mostly. However, plastic anisotropy parameter and strain hardening coefficient affect moderately buckling behaviour of steel sheets after the buckling initiation.

• International Journal of Concrete Structures and Materials
• /
• 제1권1호
• /
• pp.11-18
• /
• 2007

In the recent design of high ductile engineered cementitious composites (ECC), optimizing both processing and mechanical properties for specific applications is critical. This study employs a method to develop useful ECC produced with slag particles (slag-ECC) in the field, which possesses different fluid properties to facilitate diverse types of processing (i.e., self-consolidating or spray processing). Control of rheological modulation was regarded as a key factor to allow the performance of the desired processing while retaining the ductile material properties. To control the rheological properties of the composite, the basic slag-ECC composition was initially obtained, determined based on micromechanics and steady-state cracking theory. The stability and consequent viscosity of the suspensions were then mediated by optimizing the dosage of the chemical and mineral admixtures. The rheological properties altered through this approach were revealed to be effective in obtaining ECC-hardened properties, represented by pseudo strain-hardening behavior in uniaxial tension, allowing the readily achievement of the desired function of the fresh ECC.

• Structural Engineering and Mechanics
• /
• 제10권4호
• /
• pp.405-426
• /
• 2000

Two approximate methods based on mechanism analysis suitable for seismic assessment/design of structural concrete are reviewed. The methods involve use of equal energy concept or equal displacement concept along with appropriate patterns of inelastic deformations to relate structure's maximum lateral displacement to member and plastic deformations. One of these methods (Clough's method), defined here as a ductility-based approach, is examined in detail and a modification for its improvement is suggested. The modification is based on estimation of maximum inelastic displacement using inelastic design response spectra (IDRS) as an alternative to using equal energy concept. The IDRS for demand displacement ductilities are developed for a single degree of freedom model subjected to several accelerograms as functions of response modification factor (R), damping ratios, and strain hardening. The suggested revised methodology involves estimation of R as the ratio of elastic strength demand to code level demand, and determination of design base shear using $R_{design}{\leq}R$ and maximum displacement, determination of plastic displacement using IDRS and subsequent local plastic deformations. The methodology is demonstrated for the case of a 10-story precast wall panel building.

• 전산구조공학
• /
• 제7권3호
• /
• pp.133-141
• /
• 1994

강도활용을 극대화한 볼트의 소성역체결시 볼트의 항복은 볼트에 발생한 인장응력과 너트 나사산과의 접촉면에서 오는 마찰토오크에 의한 전단응력과의 조합에 의한 영향을 받는다. 볼트는 최소단면적인 나사부중 너트와 물리지 않은 여우나사부에서 먼저 항복을 일으킨다. 볼트재료는 대체로 항복과 더불어 소성경화를 보이며 그 정도는 고강도재료에서 인장강도의 10%정도이다. 본 연구에서는 소성역체결시의 거동해석을 변형도증분이론에 의거 해석하였다. 항복은 최소단명이 원통의 표면에서 시작되며 이를 두께가 얇은 원통으로 취급하였다. 항복의 전파는 이들 얇은 원통이 체결이 진행됨에 따라 순차적으로 항복에 이르는 것으로 보고 이 얇은 원통들을 항복시키는데 필요한 축력과 토오크를 합하여 체결종료시의 볼트축력과 (나사면마찰) 토오크로 하였다. M10미터 가는 나사를 계산과 실험에 사용하였다. 축력과 마찰토오크의 마찰계수에 대한 변화관계를 보여주는 그래프와 더불어 실험에서 사용한 볼트의 설계보조 선도를 제시하였다. 이 설계보조용 선도는 실험실에서 얻어진 토오크계수와 마찰계수와의 관계를 그린 것으로 윤활, 포면처리등 현장조건에 따라 달라진 마찰계수를 적절히 취급하는데 효과적으로 활용이 가능하다.