• 조명전기설비학회논문지
• /
• 제29권5호
• /
• pp.13-18
• /
• 2015

In this paper, we implemented a polarimetric vibration sensor using a Sagnac birefringence interferometer composed of polarization-maintaining photonic crystal fiber(PM-PCF). By changing the amplitude and frequency of vibration applied to PM-PCF employed as the sensor head of the proposed sensor, sensor responses to various types of vibration were investigated. First, the vibration characteristic of the sensor was explored for a single frequency in a frequency range from 1 to 3000Hz with a cylindrical piezoelectric transducer, and then the sensor response to naturally damped vibration was examined by utilizing a metal cantilever. It was experimentally observed that the sensor output signal was deteriorated by more than 3dB at ~1900Hz in the single frequency vibration measurement with a minimum detectable strain perturbation of ${\sim}1.34n{\varepsilon}/Hz^{1/2}$ at 1500Hz and the peak value of the sensor output signal was proportional to the strength of initially applied stress in the naturally damped vibration measurement.

• 한국지반환경공학회 논문집
• /
• 제16권6호
• /
• pp.31-38
• /
• 2015

최근 우리나라는 러시아 극동 지역의 천연파이프 건설과 제2남극기지인 장보고 기지건설이 이루어지면서 영구동토지반에서의 구조물 건설에 대한 관심이 증대되고 있다. 세립분 함유량이 동결된 사질토의 역학적 거동에 미치는 영향을 파악하기 위하여 온도 -5, -10, $-15^{\circ}C$의 조건에서 세립분 함유량 0, 5, 10, 15%의 시료에 대해 일축압축시험을 수행하였다. 동결 사질토를 성형하기 위해 입도가 균일한(SP) 주문진 표준사와 소성성이 낮은 실트(ML)인 카올리나이트를 사용하였다. 성형된 동결 사질토를 사용하여 온도를 제어할 수 있는 냉동 체임버에서 일축압축실험을 수행하였고 강도 및 강성특성을 파악하기 위해 최대 일축압축강도와 변형계수를 분석하였다. 그 결과 동결 사질토의 강도 및 강성은 세립분 함유량이 증가할수록 감소하는 경향을 보이고 온도가 낮아짐에 따라 증가하는 경향을 보였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제11권2호
• /
• pp.71-81
• /
• 1987

Nowadays, the high development of industrial technique demands the optimal design of marine structures to be welded under the water, because the underwater welding of the ship hull and marine structures can decrease manpower and cost of production. However there is not available at present any report on fatigue behavior about underwater welded joints. In this paper under tention- tension repeated fatigue stress with frequency of 10 cycles per second by local controlled system, the fatigue strength properties of underwater welded joints of SM41A-2 Plate-to-Plate of 10 mm thickness were experimentally examined. The results obtained were as follows : 1) The fatigue strength of underwater welded joints of SM41A-2 was peaked at the heat input of about 1, 400 joule/mm(180 A, 36 V), while, at the heat input of more than about 1, 100 joule/mm (160 A, 33 V) that of the underwater welds at the higher than cycle of life rather than the lower cycle was higher than that of the base metal but lower than that of the atmosphere welds on account of both cooling and notch effects. 2) The fatigue limit of underwater welds increased with an increase of heat input resulting in a peak of that at the heat input of about 1, 400 joule/mm and then decreased gradually. 3) The fatigue strength at N cycles was peaked between the heat input of about 1, 400 and 1, 700 joule/mm where the strain was rapidly increased. 4) It was confirmed that the optimal zone of heat input condition for obtaining the underwater welds fatigue strength higher than that of the base metal exists, and if out of this zone, the fatigue strength of the underwater welds was lower than that of the base metal because of lack weld penetration, inclusion of slag, voids, etc. 5) By the fatigue test, the underwater welds fractured brittly without visual deformation, so the strain was remarkably less than of the atmosphere welds. 6) The fatigue life factor was peaked at the heat input of about 1, 600 joule/mm (200 A, 36 V) at which the mean strain is a little higher than that of the base metal but quite lower than those of the atmosphere welds, resulting in good underwater welds because both fatigue strength and ductility of the underwater welds are higher than those of the base metal at such heat input.

• Geomechanics and Engineering
• /
• 제12권6호
• /
• pp.983-1001
• /
• 2017

The extent by which economy and safety concerns can be addressed in earth retaining structure design depends on the accuracy of the assumed failure surface. Accordingly, this study attempts to investigate and quantify mechanical backfill properties that control failure surface geometry of cohesionless backfills at the active state for translational mode of wall movements. For this purpose, a small scale 1 g physical model study was conducted. The experimental setup simulated the conditions of a backfill behind a laterally translating vertical retaining wall in plane strain conditions. To monitor the influence of dilative behavior on failure surface geometry, model tests were conducted on backfills with different densities corresponding to different dilation angles. Failure surface geometries were identified using particle image velocimetry (PIV) method. Friction and dilation angles of the backfill are calculated as functions of failure stress state and relative density of the backfill using a well-known empirical equation, making it possible to quantify the influence of dilation angle on failure surface geometry. As a result, an empirical equation is proposed to predict active failure surface geometry for cohesionless backfills based on peak dilatancy angle. It is shown that the failure surface geometries calculated using the proposed equation are in good agreement with the identified failure surfaces.

• Computers and Concrete
• /
• 제33권6호
• /
• pp.671-688
• /
• 2024

The modeling efficiency of concrete meso-models close to real concrete is one of the important issues that limit the accuracy of mechanical simulation. In order to improve the modeling efficiency and the closeness of the numerical aggregate shape to the real aggregate, this paper proposes a method for generating a two-dimensional concrete meso-model based on pixel matrix and skeleton theory. First, initial concrete model (a container for placing aggregate) is generated using pixel matrix. Then, the skeleton curve of the residual space that is the model after excluding the existing aggregate is obtained using a thinning algorithm. Finally, the final model is obtained by placing the aggregate according to the curve branching points. Compared with the traditional Monte Carlo placement method, the proposed method greatly reduces the number of overlaps between aggregates by up to 95%, and the placement efficiency does not significantly decrease with increasing aggregate content. The model developed is close to the actual concrete experiments in terms of aggregate gradation, aspect ratio, asymmetry, concavity and convexity, and old-new mortar ratio, cracking form, and stress-strain curve. In addition, the cracking loss process of concrete under uniaxial compression was explained at the mesoscale.

• Earthquakes and Structures
• /
• 제13권5호
• /
• pp.485-496
• /
• 2017

The behavior of 8 steel reinforced high-strength concrete (SRHSC) columns, which comprised of four identical columns with cross-shaped steel and other four identical columns with square steel tube, was investigated experimentally under cyclic uniaxial and biaxial loading independently. The influence of steel configuration and loading path on the global behavior of SRHSC columns in terms of failure process, hysteretic characteristics, stiffness degradation and ductility were investigated and discussed, as well as stress level of the longitudinal and transverse reinforcing bars and steel. The research results indicate that with a same steel ratio deformation capacity of steel reinforced concrete columns with a square steel tube is better than the one with a cross-shaped steel. Loading path affects hysteretic characteristics of the specimens significantly. Under asymmetrical loading path, hysteretic characteristics of the specimens are also asymmetry. Compared with specimens under unidirectional loading, specimens subjected to bidirectional loading have poor carrying capacity, fast stiffness degradation, small yielding displacement, poor ductility and small ultimate failure drift. It also demonstrates that loading paths affect the deformation capacity or deformation performance significantly. Longitudinal reinforcement yielding occurs before the peak load is attained, while steel yielding occurs at the peak load. During later displacement loading, strain of longitudinal and transverse reinforcing bars and steel of specimens under biaxial loading increased faster than those of specimens subjected to unidirectional loading. Therefore, the bidirectional loading path has great influence on the seismic performance such as carrying capacity and deformation performance, which should be paid more attentions in structure design.

• Geomechanics and Engineering
• /
• 제8권4호
• /
• pp.541-557
• /
• 2015

This research aims to analyze the fracture coalescence characteristics of brittle sandstone specimen ($80{\times}160{\times}30mm$ in size) containing various flaws (a single fissure, double squares and combined flaws). Using a rock mechanics servo-controlled testing system, the strength and deformation behaviours of sandstone specimen containing various flaws are experimentally investigated. The results show that the crack initiation stress, uniaxial compressive strength and peak axial strain of specimen containing a single fissure are all higher than those containing double squares, while which are higher than those containing combined flaws. For sandstone specimen containing combined flaws, the uniaxial compressive strength of sandstone increase as fissure angle (${\alpha}$) increases from $30^{\circ}$ to $90^{\circ}$, which indicates that the specimens with steeper fissure angles can support higher axial capacity for ${\alpha}$ greater than $30^{\circ}$. In the entire deformation process of flawed sandstone specimen, crack evolution process is discussed detailed using photographic monitoring technique. For the specimen containing a single fissure, tensile wing cracks are first initiated at the upper and under tips of fissure, and anti-tensile cracks and far-field cracks are also observed in the deformation process; moreover anti-tensile cracks usually accompanies with tensile wing cracks. For the specimen containing double squares, tensile cracks are usually initiated from the top and bottom edge of two squares along the direction of axial stress, and in the process of final unstable failure, more vertical splitting failures are observed in the ligament region. When a single fissure and double squares are formed together into combined flaws, the crack coalescence between the fissure tips and double squares plays a significant role for ultimate failure of the specimen containing combined flaws.

• 한국식품과학회지
• /
• 제36권4호
• /
• pp.568-573
• /
• 2004

3%의 콩단백질을 첨가한 옥수수전분 용액을 건조가열 시켜 만든 시료의 호화특성, 겔의 조직감 및 노화특성에 대해 연구하였다. 건조가열로 만들어진 시료의 경우, 단순 혼합 시료보다 낮은 pasting 온도와 높은 RVA 점도들을 보였으며 유의적으로 낮은 호화엔탈피를 보였다. 높은 온도에서 건조가열한 시료(heated sample)의 경우, 낮은 온도에서 건조가열한 시료(unheated sample)보다 pasting 온도가 낮았으며 peak viscosity, breakdown viscosity가 유의적으로 높았다. 또한 pH가 증가할수록 보다 높은 점도 profile을 보였다. 가열 건조한 시료는 낮은 파괴강도 및 파괴 strain을 보였으며 pH가 높을수록 elastic modulus와 파괴강도는 감소하고 파괴 strain은 증가하였다. 콩단백질의 첨가와 더불어 건조가열은 전분의 노화방지에 도움을 주며 겔의 미세구조를 변화시켜 겔의 조직감을 변화시켰다. 전분의 호화 및 노화특성과 겔의 조직감을 콩단백질의 첨가와 더불어 건조가열과 pH 조절을 이용하여 변화시킬 수 있었으며, 이는 전분의 호화온도와 단백질의 변성온도 이하의 온도에서 건조 후 고온 건조가열을 통해 전분-단백질의 구조적 변성과 결합을 유도하여 새로운 기능성 전분을 만들 수 있는 가능성을 보여준다.

• 대한토목학회논문집
• /
• 제8권1호
• /
• pp.33-40
• /
• 1988

흙과 보강재 사이의 거동을 측정하는 수단으로서 hollow cylinder type의 샘플 내에 보강재를 인장방향으로 삽입하여 주위압력을 일정하게 유지한 가운데 축력(軸力)을 감소시키는 소위 삼축인장시험을 실시하였다. 인장특성(引張特性)(extensibility)이 상이(相異)한 3종류의 보강재를 사용한 결과 파괴변형율(failure strain), 최대강도후의 응력강소(loss of post-peak strength), 변형모양(deformation mode) 등이 보강재에 따라 각각 독특하였고, 파괴의 양상은 breakage 또는 pull-out 이 발생하였으며, 보강재단(補强材端)의 고정여부에 따라 보강효과가 영향을 받음이 확인되었다. 따라서 보강토해석 및 설계시 흙 및 보강재 자체의 강도(强度)와 더불어 보강재의 인장특성(引張特性)과 경계조건(境界條件)이 매우 중요한 고려요소임을 알 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.869-872
• /
• 2008

최근, 고온가열을 받은 콘크리트의 압축강도, 탄성계수 및 최대하중에서의 변형에 대한 체계적인 연구가 실험적으로 접근되고 있다. 본 연구는 40, 60, 80MPa급 고강도콘크리트의 재료역학적 특성에 있어서 $20{\sim}700^{\circ}C$ 범위로 상승되는 온도의 영향을 연구하는데 그 목적이 있다. 본 연구에서 제안한 시험법은 설계하중 사전재하 및 잔존강도 시험방법으로서 극한강도의 25%하중을 사전재하한 후 시험체의 가열을 하중을 유지한 상태에서 목표온도까지 가열하였고 재하는 고온상태 및 상온에서 24시간 냉각상태에서 시험체가 파괴될 때까지 재하를 실시했다. 시험결과 콘크리트 강도가 증가할수록 상온의 수준과 비교하여 고온에서의 상대적인 압축강도와 탄성계수는 감소하는 것으로 나타났으며 실험결과를 바탕으로 온도의 수준에 따른 압축강도와 탄성 계수의 상관 관계식을 도출하였다.