• 펄프종이기술
• /
• 제39권4호
• /
• pp.21-28
• /
• 2007

A simple method of on-line stiffness measurement using the wrinkling behavior of paper web between two rollers was presented. The theory and the equation were presented, and lab and mill tests were executed. We called the stiffness measured by Taber tester as 'Taber stiffness', and by tension wrinkling measurement as 'wrinkle stiffness', respectively. Lab experimental results showed Taber and wrinkle stiffness are almost equivalent. In the mill experiment, we could measure the stiffness in the wet state and in the dry state. The dry wrinkle stiffness was close to the taber stiffness, but the wet wrinkle stiffness was much lower than the corresponding taber stiffness.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.317-318
• /
• 2010

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1474-1482
• /
• 1994

In order to study the influence of a circular inclusion on a stress field neat a crack tip, mutual interference of a crack and the circular inclusion is analyzed by using the two dimensional boundary element method program made for the analysis of a bimaterial inclusion. The stress intensity factor of an inclusion which has small stiffness is a little greater than that of large stiffness in the near-by crack tip, and similar values tends to appear for distant crack tips. A line crack shows the repetition phenomena which caused by stress mutual interference depending on the radius and stiffness of an inclusion, and the repetition phenomena becoms weak in the inclusion which has large stiffness. Stress mutual interference shows repetition phenomena after extension of a line crack by the length of the radius of the inclusion which has small stiffness.

• Steel and Composite Structures
• /
• 제5권1호
• /
• pp.1-15
• /
• 2005

Important characteristics of the previously proposed reduced stiffness method and a summery of its design curves for the buckling of the axially loaded sandwich cylindrical shells is presented. Comparison of the lower bound obtained with FEM analysis with that from the reduced stiffness analysis shows that the proposed reduced stiffness method can provide safe lower bounds for the buckling of geometrically imperfect, axially loaded sandwich cylindrical shells. One of the attractive features of the reduced stiffness elastic lower bound analysis is that it provides safe estimates of buckling loads that do not depend on the specification of the precise magnitude of the imperfection spectra. As a result, designers can readily apply this method without being worried about possible geometrical imperfections that might be generated during fabrication and construction of sandwich cylindrical shells.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.941-948
• /
• 2006

In this paper, the effect of stiffness on hydroelastic responses of plate-like floating structure under wave loads are studied. Direct method is used for the numerical analysis. In the numerical analysis, structural equation is formulated by finite element method(FEM) and higher order boundary element method(HOBEM) is employed for the analysis of fluid flow. A 1000m-long VLFS(Very Large Floating Structure) is considered in numerical analyses. By analyzing VLFS for various cases of stiffness, the characteristics of hydroelastic responses with the variation of stiffness are investigated.

• Tribology and Lubricants
• /
• 제28권6호
• /
• pp.289-296
• /
• 2012

Atomic force microscopy (AFM) has been used for imaging surfaces and measuring surface forces at the nano-scale. Force calibration is important for the quantitative measurement of forces at the nano-scale using AFM. Normal force calibration is relatively straightforward, whereas the lateral force calibration is more complicated since the lateral stiffness of the cantilever is often comparable to the contact stiffness. In this work, the lateral force calibrations of the rectangular cantilever were performed using torsional Sader's method, thermal noise method, and wedge calibration method. The lateral optical lever sensitivity for the thermal noise method was determined from the friction loop under various normal forces as well. Experimental results showed that the discrepancies among the results of the different methods were as large as 30% due to the effect of the contact stiffness on the lateral force calibration of the cantilever used in this work. After correction for the effect of contact stiffness, all the calibration results agreed with each other, within experimental uncertainties.

• 한국자동차공학회논문집
• /
• 제8권4호
• /
• pp.177-185
• /
• 2000

The deformation characteristics is one of the major factors to resume the crash configuration in collision accident reconstruction. Crash analysis are carried out using finite element method and body stiffness equations representing force-deformation relationship are derived, Two different crash conditions : 1) frontal barrier impact 2) frontal impact between cars are given for the derivation of the equations. The stiffness coefficient of equation by method 2) is larger than that by method. 1). Crash analysis between two vehicles is accomplished with three crash angles and three velocities for each angle condition. The deformations are measured for six selected points and deformation energies are calculated using the derived equations. Equation by method 2) results in better estimation of deformation energy than that by method 1) for all crush configurations. The estimated energies can be utilized as one of indices to identify the type of the collision accident result.

• 한국소음진동공학회논문집
• /
• 제11권9호
• /
• pp.462-474
• /
• 2001

In this paper, Generalized Differential Quadrature Method is applied to the buckling analysis of built-up columns without or with stay plates. numerical analysis using GDQM is carried out for various boundary conditions(simply supported conditions, fixed conditions, fixed-simply supported conditions), dimensionless stiffness parameter and dimensionless inertia moment parameter. The accuracy and convergence of solutions are compared with exact solutions of Gjelsvik to validate the results of GDQM. Results obtained by this method are as follows. 91) This method can yield the accurate numerical solutions using few grid points. (2) The buckling load of built-up column increases as the dimensionless stiffness parameter decreases. (3) The effects of boundary conditions on the buckling load are not considerable as the dimensionless stiffness parameter increases. (4) The buckling load of built-up column increases due to the stay plate.

• Nuclear Engineering and Technology
• /
• 제27권5호
• /
• pp.760-766
• /
• 1995

Young's Modulus와 단지 기하학적 테이타를 이용하여 흘드다운스프링의 탄성강성도를 해석하는 방법을 제시하였다. 제시된 이 방법은 엔지니어링 빔이론과 카스티릴아노 이론을 이용하여 판형흘드다운스프링의 탄성강성도 해석에 적용하였다. 이러한 방법의 효율성과 신뢰성을 보여주기 위하여 제안된 방법으로 부터의 탄성강성도를 여러가지 형태의 홀드다운스프링의 시험결과와 비교하였다. 이러한 결과비교에 의해 제안된 방법이 판형홀드다운스프링의 탄성강성도를 구하는데 있어서 효과적임을 입증하였다.

• 동력기계공학회지
• /
• 제11권1호
• /
• pp.92-97
• /
• 2007

It is important to compute the structural analysis of plate structures in structural design. In this paper, the author uses the finite element-transfer stiffness coefficient method (FE-TSCM) for the structural analysis of plate structures. The FE-TSCM is based on the concept of the successive transmission of the transfer stiffness coefficient method and the modeling technique of the finite element method (FEM). The algorithm for in-plane structural analysis of a rectangular plate structure is formulated by using the FE-TSCM. In order to confirm the validity of the FE-TSCM for structural analysis of plate structures, two numerical examples for the in-plane structural analysis of a plate with triangular elements and the bending structural analysis of a plate with rectangular elements are computed. The results of the FE-TSCM are compared with those of the FEM on a personal computer.