• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.371-376
• /
• 1999

Stick-slip friction is present to some degree in almost all actuators and mechanisms and is often responsible for performance limitations. Simulation of stick-slip friction is difficult because of strongly nonlinear behavior in the vicinity of zero velocity. A straightforward method for representing and simulating friction effects is presented. True zero velocity sticking is represented without equation reformulation or the introduction of numerical stiffness problems. Stick-slip motion is investigated experimentally, and the fundamental characteristics of the stick-slip motion are clarified. Based on these experimental results, the characteristics of static in the period of stick and kinetic friction in the period of slip are studied concretely so as to clarify the stick-slip process.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.643-648
• /
• 2011

Fatigue crack in most rails take place by rolling contact between wheel and rail in railway industry. Therefore, it is critical to understand the rolling contact phenomena, especially for the three-dimensional situation. In this paper the steady-state rolling contact problem of KTX wheel and rail (UIC60) has been studied with three-dimensional finite element analysis. The variation of contact pressure and contact stresses on rolling contact surface were obtained using the finite element method. The three-dimensional distribution of contact stresses on the contact surface are investigated. Results show that the distribution of shear stress and contact stress (von Mises) on the contact surface varies rapidly as a result of the variation of stick-slip region. The contact stress at the leading edge is greater than at the trailing edge because of stick and slip phenomena.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1996년도 제24회 춘계학술대회
• /
• pp.25-29
• /
• 1996

The fretting wear characteristics for Zircaloy-4 tube used as fuel rod in the nuclear power plant have been investigated. The fretting wear tester was designed and manufactured for this experiment. This study was focused on main factors of fretting wear, cycle, slip amplitude and normal load. The worn surfaces were observed by SEM.

• 한국정밀공학회지
• /
• 제28권5호
• /
• pp.565-571
• /
• 2011

Because most fatigue cracks in wheel and rail take place by rolling contact of wheel and rail in railroad industry, it is critical to understand the rolling contact phenomena, especially for the three-dimensional situation. This paper presents an approach to steady-state rolling contact problem of three-dimensional contact bodies, with or without tangential force, based on the finite element method. The steady-state conditions are controlled by the applied relative slip and tangential force. The three-dimensional distribution of tangential traction and contact stresses on the contact surface are investigated. Results show that the distribution of tangential traction and contact stresses on the contact surface varies rapidly as a result of the variation of stick-slip region. The tangential traction is very close in form to Carter's distribution.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.799-804
• /
• 2003

Friction phenomenon can be described as two parts which are pre-sliding and sliding regions. In motion of the sliding region, friction forces depend on the velocity of the system and are known as Coulomb, stick-slip, stribeck effect and viscous friction. The pre-sliding region, which is before breakaway, depends on the position of the system. The motion of friction in the sliding region can be described as the LuGre model. But the pre-sliding motion of friction, which has hysteresis characteristics in general, is not known widely. Therefore, an improved friction model, which can describe the motion of friction in the pre-sliding region, is proposed in this paper. And simulation and experimental results show the effectiveness of the proposed friction model for precise tracking control systems.

• Journal of Mechanical Science and Technology
• /
• 제18권10호
• /
• pp.1755-1762
• /
• 2004

Friction phenomenon can be described as two parts, which are the pre-sliding and sliding regions. In the motion of the sliding region, the friction force depends on the velocity of the system and consists of the Coulomb, stick-slip, Streibeck effect and viscous frictions. The friction force in the pre-sliding region, which occurs before the breakaway, depends on the position of the system. In the case of the motion of the friction in the sliding region, the LuGre model describes well the friction phenomenon and is used widely to identify the friction model, but the motion of the friction in the pre-sliding such as hysteresis phenomenon cannot be expressed well. In this paper, a modified friction model for the motion of the friction in the pre-sliding region is suggested which can consider the hysteresis phenomenon as the Preisach model. In order to show the effectiveness of the proposed friction model, the sliding mode controller (SMC) with hysteresis friction compensator is synthesized for a ball-screw servo system.

• 대한기계학회논문집
• /
• 제18권8호
• /
• pp.2026-2038
• /
• 1994

A numerical scheme is developed for the analysis of incipient sliding contact with orthotropic friction condition subjected to tangential load and twisting moment. The inherent nonlinearity in the orthotropic friction law has been treated by a polyhedral friction law. Then, a three-dimensional linear complementarity problem(LCP) formulation in an incremental form is obtained, and the existence of a solution is investigated. A Lemke's complementary pivoting algorithm is used for solving the LCP. The scheme is illustrated by spherical contact problems, and the effects of eccentricity of elliptical friction domain on the traction and stick region are discussed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.60-63
• /
• 2000

In this study, efficient force reflection algorithm is developed for the Haptic Display by using a proxy concept and friction model. When there are not any contacted obstacles the proxy is following human operator's command trajectory in the 3D virtual space. But when the operator's command trajectory is locating inside of the object, the proxy is constrained by the surface of the object. Here only with the information of the proxy position and operator's command trajectory at every time step, we can calculate the reflection force and its orientation. To display the friction force between two virtual stiff material which are sliding against each other, modified Karnopp's friction model is used. In the friction model, a damping term and a Stribeck effect term are included to display the relative velocity effect and stick-slip effect at the very low relative velocity region respectively.

• 대한기계학회논문집
• /
• 제8권6호
• /
• pp.591-598
• /
• 1984

본 논문에서는 고체상호간 미끄름접촉에 의해 발생하는 진동과 소음의 특성을 조사하기 위해서 실험과 이론해석을 행하였다. 미끄름접촉과 관련된 소음에는 brake squeal 혹은 wheel screech등과 같이 stick-slip 형태의 동적 불안정 상태와 관련이 있는 squeal noise와, 겉보기로 동적 안정 상태에 있으나 미끄름접촉면간에 내재하는 미끄름접촉 고유의 불규칙한 동특성에 기인하여 발생하는 rubbing noise가 있다. 본 연구의 대상은 보다 기본적인 형태인 후자에 한한다.

• 한국철도학회논문집
• /
• 제8권6호
• /
• pp.573-580
• /
• 2005

Model I interlaminar fracture behaviors of the carbon/epoxy composite, one of the candidate composites for a tilting train carbody, were investigate by the use of DCB(Double cantilever beam) specimens. These specimens were made of CF3327 plain woven fabric with epoxy resin, and an artificial starter delamination was fabricated by inserting Teflon film with the thickness of $12.5{\mu}m$ of $25.0{\mu}m$ at the one end of the specimen. Mode I interlaminar fracture toughness was evaluated for the specimens with the different thickness of an inserter. Also delamination propagating behaviors and interlaminar fracture surface were examined through an ooptical travelling scope and a scanning electron microscope. We found that abruptly unstable crack propagation called as stick-slip phenomena was observed. In addition, interlaminar fracture behaviors were affected on the location and the morphology of a crack tip as well as an interface region.