• Journal of International Society for Simulation Surgery
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2017

In the field of tissue engineering, researches have been actively conducted to regulate stem cell fate by understanding the interaction between cell and materials. This approach is expected as a promising therapeutic method in the future medicine by utilizing differentiation of stem cells into desired cells or tissues using biomaterial. For this regenerative medicine, there exist lots of attempts to construct optimized structures of various shapes and sizes that can regulate the stem cell fate. In this review, we will empathize the topographic effect as stem cell niche on the mesenchymal stem cell (MSC) response (cell attachment, proliferation, and differentiation) according to the shape and size of the structure of the substrates, and comprehensively analyze the importance and the effect of shape and size of the surface topography.

• Journal of Korean Society of Forest Science
• /
• v.96 no.3
• /
• pp.362-368
• /
• 2007

This study was conducted to estimate merchantable volume and yield per diameter (DBH) class of Pinus koraiensis and Larix kaempferi. Stem volume of trees in each diameter class was calculated using the existing equations for taper and height curve. Saw logs and pulpwood volume were then estimated from the stem volume in each diameter class. The final step was to estimate merchantable volume and yield from saw logs, assuming saw logs were used for lumber (boards or dimension products) production only. The results showed that the stem volume of Larix kaempferi was 23~38% higher than that of Pinus koraiensis at the same diameter classes. Both species were able to produce saw logs from the diameter class of 18 cm. Saw logs and pulpwood yield for both species rapidly increased due to the size limitation on small end diameter. This yield reached a maximum of 90% and 88% at 26 cm and 38cm diameter class, respectively, for Pinus koraiensis and Larix kaempferi. Lumber yield estimated for board products ranged from 23% to 56%. In the case of dimension products, Lumber yield became significantly smaller as saw logs were used for larger dimension products. These results can be used for calculating merchantable volume and economic value of trees, as well as determining final lumber products.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2000.10a
• /
• pp.74-77
• /
• 2000

Porthole die extrusion has a great advantage in the forming of hollow section tubes difficult to produce by conventional extrusion with a mandrel on the stem. Because of the complicated structure of die assembly, extrusion process as a forming of hollow section tubes has been investigated experimentally Therefore, analytic approaches that are useful in profitable die design and in the improvement of productivity are inevitably demanded Welding strength is affected by many parameters, which are such as extrusion ratio, extrusion speed, die shape, porthole number, bearing length, billet temperature and mandrel shape. In this paper, the parameters, which are such as billet temperature, bearing length and tube thickness, are examined. The welding pressures are examined through 3D simulation of non steady state and compared with experimental results.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.8
• /
• pp.891-898
• /
• 2005

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint race, and energy required lot welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy amount of upset. working time, and residual stresses in the joint. Inertia welding was conducted to make the large exhaust valve spindle for low speed marine diesel engine. superalloy Nimonic 80A for valve head of 540mm and high alloy SNCrW for valve stem of 115mm. Due to different material characteristics such as, thermal conductivity and flow stress. on the two sides of the weld interface, modeling is crucial in determining the optimal weld geometry and Parameters. FE simulation was performed by the commercial code DEFORM-2D. A good agreement between the Predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters. especially for welds for which are very expensive materials or large shaft. Many kinds of tests, including macro and microstructure observation, chemical composition tensile , hardness and fatigue test , are conducted to evaluate the qualify of welded joints. Based on the results of the tests it can be concluded that the inertia welding joints of the superalloy exhaust valve spindle are better properties than the material specification of SNCrW.