• Structural Engineering and Mechanics
• /
• 제82권2호
• /
• pp.173-189
• /
• 2022

This study presents an experimental and numerically study about the effects of fiber reinforcement ratio on the behavior of concrete-filled steel tubes (CFST) under dynamic impact loading. In literature have examined the behavior of GFRP and FRP wrapped strengthened CFST elements impact loads. However, since the direction of potential impact force isn't too exact, there is always the probability of not being matched the impact force of the area where the reinforced. Therefore, instead of the fiber textile wrapping method which strengthens only a particular area of CFST element, we used fiber-added concrete-filled elements which allow strengthening the whole element. Thus, the effect of fiber-addition in concrete on the behavior of CFST elements under impact loads was examined. To do so, six simply supported CFST beams were constructed with none fiber, 2% fiber and 10% fiber reinforcement ratio on the concrete part of the CFST beam. CFST beams were examined under two different impact loads (75 kg and 225 kg). The impactors hit the beam from a 2000 mm free fall during the experimental study. Numerical models of the specimens were created using ABAQUS finite element software and validated with experimental data. The obtained results such as; mid-span displacement, acceleration, failure modes and energies from experimental and numerical studies were compared and discussed. Furthermore, the Von Misses stress distribution of the CFST beams with different ratio of fiber reinforcements were investigated numerically. To sum up, there is an optimum amount limit of the fiber reinforcement on CFST beams. Up to this limit, the fiber reinforcement increases the structural performances of the beam, beyond that limit the fiber reinforcement decreases the performances of the CFST beam under transverse impact loadings.

• 대한토목학회논문집
• /
• 제26권4A호
• /
• pp.743-752
• /
• 2006

다축 응력 상태의 구속된 콘크리트는 구속되지 않은 콘크리트에 비해 강도가 크게 증가한다고 알려져 왔고, 많은 연구자들은 아직도 여러 분야에서 구속된 콘크리트에 대한 연구를 진행 중에 있다. 최근 FRP를 이용한 구속된 콘크리트에 대한 많은 연구가 진행 중에 있지만, FRP는 높은 강도에 비해 취성 재료여서 실제 구조물 적용에 많은 어려움이 있다. 본 연구에서는 높은 강도 및 연성을 갖는 강재로 구속된 콘크리트에 대하여 강재의 구속 강성이 콘크리트의 강도 증진 및 연성거동에 미치는 영향을 알아보기 위해 51개의 시험체를 통해 비교 분석해 보았다. 이 실험을 통해 구속된 콘크리트의 강도 증진 효과 및 연성 거동이 뛰어나게 증가함을 확인하였다. 또한 실험 결과를 회귀분석하여 구속 강성이 콘크리트 응력-변형률 곡선에 미치는 영향을 고려한 CSS(원형 강재 구속 시험체)와 R4S(사각형 이방향 강재 구속 시험체)에 대한 응력-변형률 모델을 제안하였다.

• Steel and Composite Structures
• /
• 제51권6호
• /
• pp.679-695
• /
• 2024

This paper presents a novel technique that combines machine learning (ML) with moth-flame optimization (MFO) methods to predict the axial compressive strength (ACS) of concrete filled double skin steel tubes (CFDST) columns. The proposed model is trained and tested with a dataset containing 125 tests of the CFDST column subjected to compressive loading. Five ML models, including extreme gradient boosting (XGBoost), gradient tree boosting (GBT), categorical gradient boosting (CAT), support vector machines (SVM), and decision tree (DT) algorithms, are utilized in this work. The MFO algorithm is applied to find optimal hyperparameters of these ML models and to determine the most effective model in predicting the ACS of CFDST columns. Predictive results given by some performance metrics reveal that the MFO-CAT model provides superior accuracy compared to other considered models. The accuracy of the MFO-CAT model is validated by comparing its predictive results with existing design codes and formulae. Moreover, the significance and contribution of each feature in the dataset are examined by employing the SHapley Additive exPlanations (SHAP) method. A comprehensive uncertainty quantification on probabilistic characteristics of the ACS of CFDST columns is conducted for the first time to examine the models' responses to variations of input variables in the stochastic environments. Finally, a web-based application is developed to predict ACS of the CFDST column, enabling rapid practical utilization without requesting any programing or machine learning expertise.

• 한국구조물진단유지관리공학회 논문집
• /
• 제22권1호
• /
• pp.176-182
• /
• 2018

본 연구의 목적은 볼접합부를 갖는 원형강관의 좌굴실험 결과를 토대로 하여 국내외 압축재 설계규준과 비교 평가함으로써 부재의 좌굴내력 및 좌굴길이 계수의 안전성과 합리성을 조사하는 것이다. 좌굴성능 평가를 위해 선정된 원형강관은 Ø$48.6{\times}2.8t$와 Ø$60.5{\times}3.2t$ 및 Ø$76.3{\times}3.2t$이다. 국내외 압축재 설계를 위해 우리나라의 하중저항계수 설계법(LRFD), 일본의 한계상태 설계법(LSD) 및 영국의 BS5950 규준을 적용하였다. 본 연구에서는 선행연구의 실험결과와 국내외 설계규준과의 좌굴성능을 비교 분석하였다. 그 결과를 요약해 보면 다음과 같다. 각국의 압축재 설계규준에서 부재의 전체길이를 좌굴길이로 적용한 결과 실험에 의한 좌굴내력의 64%~89% 정도로 나타났다. 따라서 안전을 위해 현재 설계 규준식에 준하여 부재설계를 수행하는 것이 바람직하다고 판단되었다. 실험결과 측정된 좌굴내력은 우리나라, 일본 및 영국의 압축재 설계규준에서 좌굴길이를 순수 원형강관만으로 고려한 좌굴내력 값에 비해 1.02배~1.43배 높은 것으로 나타났다. 따라서 스페이스 프레임 구조물 설계에 있어 개별부재 좌굴내력은 절점 간 길이가 아닌 순수 원형강관의 길이로 좌굴계수를 고려할 필요가 있을 것으로 보여 진다.

• 한국자기학회지
• /
• 제21권4호
• /
• pp.136-140
• /
• 2011

고온에서 운용 중인 설비의 안전성 평가를 위하여 사용기간 동안 열화된 재료의 물성을 측정하여야 하나, 운용 중인 설비에서 열화도가 다른 여러 종류의 시편을 획득하기가 쉽지 않다. 따라서 본 연구에서는 열교환기의 튜브와 압력용기의 재료로 널리 사용되고 있는 1Cr-0.5Mo 강을 인공열화시켜 시편으로 사용하였다. 열화도 평가를 위하여 바크하우젠 노이즈의 포락선(envelope)에서 첨두값(peak value) 사이의 간격, 보자력 및 경도를 실온에서 측정하였다. 열화도의 증가에 따라 세 값은 모두 감소하였는데, 이는 기지의 탄화물 입자가 조대화 됨으로써 탄화물 석출에 의한 기지의 연화가 결정립계의 경화보다 우세하게 작용하여 나타나는 것으로 판단되었다. 포락선 첨두값 사이의 간격과 경도값의 선형관계를 이용하여 자기적 특성 측정에 의해 간접적으로 1Cr-0.5Mo 강의 열화도를 비파괴적으로 평가할 수 있는 근거를 제시하였다.

• 대한기계학회논문집A
• /
• 제31권12호
• /
• pp.1188-1193
• /
• 2007

This study focuses on the corrosion problems of STS316(stainless steel 316) tube for the cooling system of PEMFC (Proton Exchange Membrane Fuel Cell) operation. Deionized water which is highly corrosive is used especially for cooling agent of PEMFC to eliminate electrical conductivity, The tensile stress analysis was performed to check the change of mechanical strength of cooling line and pH of the water was monitored for the observation of extent of corrosion at simulated PEMFC operating condition. When STS316 tube was exposed to deionized water for 500 hours, substantial cracks were found on the surface and the pH of water was decreased from 6.8 to 5.8. For prevention of corrosion problems, the STS316 was coated by three kinds of fluororesin such as PTFE, FEP and ETFE. Among the coating materials, PTFE was the most protective in corrosive environment and was maintained the mechanical strength. To lower the cost, the same experimental analyses were carried out for iron tubes and the result will be discussed in detail.

• 한국표면공학회지
• /
• 제34권6호
• /
• pp.575-584
• /
• 2001

Erosion due to abrasive particles contained in gas streams from boilers has been emerged as a significant problem in the coal fired power plants. Particle erosion accounted for approximately 50% of boiler failures and especially flyash erosion was responsible for 20~30% of emergency boiler shutdowns. Particularly, because of the high ash loading and high velocity, most erosion occurs in the boiler tubes and economiser tube bank where the direction of the gas stream changes to $180^{\circ}$ .In this study, a high temperature particle erosion tester was used to evaluate erosion rate in a simulated environment. The erosion parameters such as erosion temperature, particle impact angle, particle velocity and various particle size were changed. Flyash is the combustion product of the pulverized coal, where size is ranging from 1 to $200\mu\textrm{m}$. Flyash composed of mainly SiO$_2$, $A1_2$$_O3$, and $Fe_2$$O_3$has dense spherical particles and irregular particles containing numerous pores and cavities. From the erosion tests at various conditions, the maximum erosion was experienced at impact angles of $30^{\circ}$ to $60^{\circ}$ In addition, erosion rate increased in proportional to velocity and temperature. And from the observation of the eroded surfaces, it was also concluded that 304 stainless steel was mainly eroded by extrusion-forging at high impact angle ($90^{\circ}$) and by microcutting mechanism at low impact angles ($30^{\circ}$ and $45^{\circ}$).

• Steel and Composite Structures
• /
• 제28권5호
• /
• pp.541-557
• /
• 2018

This paper presents the influence of carbon nanotubes (CNTs) waviness and aspect ratio on the vibrational behavior of functionally graded nanocomposite sandwich annular sector plates resting on two-parameter elastic foundations. The carbon nanotube-reinforced (CNTR) sandwich plate has smooth variation of CNT fraction along the thickness direction. The distributions of CNTs are considered functionally graded (FG) or uniform along the thickness and their mechanical properties are estimated by an extended rule of mixture. In this study, the classical theory concerning the mechanical efficiency of a matrix embedding finite length fibers has been modified by introducing the tube-to-tube random contact, which explicitly accounts for the progressive reduction of the tubes' effective aspect ratio as the filler content increases. Effects of CNT distribution, volume fraction, aspect ratio and waviness, and also effects of Pasternak's elastic foundation coefficients, sandwich plate thickness, face sheets thickness and plate aspect ratio are investigated on the free vibration of the sandwich plates with wavy CNT-reinforced face sheets. The study is carried out based on three-dimensional theory of elasticity and in contrary to two-dimensional theories, such as classical, the first- and the higher-order shear deformation plate theories, this approach does not neglect transverse normal deformations. The sandwich annular sector plate is assumed to be simply supported in the radial edges while any arbitrary boundary conditions are applied to the other two circular edges including simply supported, clamped and free.

• 설비공학논문집
• /
• 제4권4호
• /
• pp.342-350
• /
• 1992

An experimental investigation of the stenosis effects on the pressure drop and flow change in the internal flow is presented. Stainless steel tubes of small diameter(3.175mm, 3.4mm) are used for the test section of the flow loop. Percent contraction ranges from 35% to 83% and the stenosis length ratio (L/d) is varied from 2.8 to 8. Water and aqueous glycerol solutions are used for Newtonian fluids and polymer solutions of Separan AP-273 (500 wppm, 1000 wppm) for non-Newtonian fluids. Pressure loss coefficients of non-Newtonian fluids decrease just as those of Newtonian fluids. The loss coefficients of Newtonian and non-Newtonian fluids increase as the percent contraction increases and the loss coefficients of non-Newtonian fluids are larger than those of Newtonian fluids for the same stenosed tube. The loss coefficient increases as the stenosis length ratio increases.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 A
• /
• pp.265-268
• /
• 2000

In this study, a small punch creep (SP-Creep) test using miniaturized specimen has been described for the development of the new creep test method for high temperature structural components such as headers and tubes of boiler, turbine casing and rotor, and reactor vessel. The SP-Creep testing technique has been applied to 1Cr-0.5Mo steel used widely as boiler header material and the creep test temperature are varied at $550^{\circ}C{\sim}600^{\circ}C$. From the experimental results, e.g. SP-Creep curve behaviors, the creep rate in steady state and creep rupture life with test temperature and load, the load exponential value(n, m), the activation energy($Q_{spc}$), the Monkman-Grant relation and the creep life assessment equation etc., it can be summarized that the SP-Creep test may be a useful test method to evaluate the creep properties of the heat resisting material such as boiler header.