• Proceedings of the KWS Conference
• /
• 2001.05a
• /
• pp.201-204
• /
• 2001

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.127-140
• /
• 1994

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. In the resistance spot welding processes the size of molten nugget is a criterion to assess weld quality. Many research have founded on measuring weld nugget size at the same time monitoring welding process parameters such as dynamic resistance and electrode movement. With increasing demand of energy saving, many efforts were made to employ aluminum alloys that are lighter than steel and have relatively equivalent strength to steel in the automobile industry. In this paper, spot weldability of aluminum alloys for various welding conditions were examined by series of experiments. One of the 6000 series (Mg-Si) aluminum alloy, 6383-T4 was chosen, which is currently considered as a substitute for the galvanized steel. Dynamic resistance, electrode movement and corresponding nugget size were observed and compared to the case of steel. Finally, resistance spot welding of dissimilar material (galvanized steel-aluminum alloy) was attempted.

• Journal of Welding and Joining
• /
• v.14 no.5
• /
• pp.59-68
• /
• 1996

This study was aimed to characterize the laser cutting process for the cold rolled stainless steel sheet. The principal process parameters of the cutting process were applied to both the continuous wave form and the pulsed wave form for the laser output mode. The laser-oxygen cutting process and the laser-nitrogen cutting process were also considered to characterize the quality and efficiency of the cutting process. The laser-oxygen cutting process revealed the better productivity than the laser-nitrogen cutting process, since the laser energy and the exothermic oxidation energy exerted on the laser-oxygen cutting process simultaneously during the entire cutting process. However, the straightness of the cutting section, which was considered as the most important factors, was inferior to that of the laser-nitrogen cutting process due to the formation of chromum oxide on the cutting surface. Frequency and duration of the pulsed wave form act as the main factors for the better quality, When the frequency increased from 100 Hz to 200 Hz and the duty increased from 20% to 40%, the quality factors such as the height of dross and the surface roughness were improved remarkably. The increase in the frequency from 200 Hz to 300 Hz, on the other hand, revealed the less effective in the cutting quality.

• Transactions of Materials Processing
• /
• v.26 no.6
• /
• pp.348-355
• /
• 2017

In recent years, dissimilar materials such as aluminum, magnesium, titanium, and advanced high strength steel are widely used in automotive body due to environment concerns and fuel consumption. Therefore, joining technology is important for assembling components made of dissimilar materials. In this study, friction stir hole clinching (FSHC) was proposed as a new mechanical joining method to join dissimilar materials. This process stirs and heats the upper sheet, forming mechanical interlocking with the lower sheet. The feasibility of this FSHC process was verified by comparing cross-section of joint in FSHC and hole clinching process under the same processing condition. Taguchi method was also applied to the FSHC process to estimate the effect of process parameters on joint strength and obtain optimal combination of process parameters. Joint strength of FSHC with optimal process condition was compared to that of FSHC with initial process condition as well as that of hole clinching with optimal process condition. Results showed that the FSHC process was useful for joining dissimilar materials, even if the formability of materials was low.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.342-344
• /
• 2007

The resistance spot weldability of surface textured cold-rolled steel sheet was evaluated. One steel sheet(T4.5) showed reduced electrode life with less than 2000 welds, and all other steel sheets(E2.2, E4.5, T2.2) made more than 2500 welds. The carbon imprint test revealed that there is sudden electrode diameter increase around 1700 welds. It is believed that the increased electrode diameter decreased current density, and resulted in decreasing weld electrode life due to small weld button size. It is considered that surface roughness difference may attribute to heating during weld cycle and reduced the weld electrode life.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.503-506
• /
• 2005

The purpose of this study was the Development of Retrofit Method for Beam Using Steel Plate Reinforced by Fiber Sheet.1. Additional reinforcements are not needed in the joining area of slab and beam web.2. Beam using carbon fiber reinforced plastic displays low effects in shearing effect.3. Beams reinforced steel plate by epoxy effect the capacities of strength. But the capacities of strength are rapidly reduced when adhesive surface be omitted. Thus details are needed in this case.4.Retrofit method for beam using steel plate reinforced by fiber sheet with epoxy rosin improves the capacities of strength and the initial stiffness, shows a large transformation since the maximum load likewise may be excellent to the shearing reinforcement.

• Journal of Welding and Joining
• /
• v.17 no.5
• /
• pp.83-88
• /
• 1999

In this paper resistance projection weldability of Zn coated steels with post treatment has been discussed. Projection welding was performed by a condenser discharge type power source which was equipped with welding parameter monitoring system. Mechanical test results indicated that the effect of post coatings on the projection front changed showing very small very small spattering at the weld strength was negligible. However, contamination rate of the block electrode varied depending on the post treatment coatings. Test results also showed that projection height before welding should be kept to be 80-100% of the specimen thickness as far as the surface quality was taken into consideration. Based on the high speed photography, discharge condition at the beginning stage of the welding process. It was considered that the spattering reduced the weld strength slightly at the optimum heat input range.

• Journal of Welding and Joining
• /
• v.12 no.2
• /
• pp.76-86
• /
• 1994

Spot welding behavior of galvanized steel has been studied using both numerical and experimental techniques. The model that used to calculate temperature distribution within weldment is two-dimensional axis-symmetric finite difference method, and nugget sizes of specimen welded in condition of welding current and time has been estimated by experiment Results have shown that nugget sizes are increased in proportion to welding current and time, but the growth rate of nugget is decreased. Shear-tensile strength tests have shown interface fracture when welding current is 7, 9KA, welding time is 8-14cycle and 11KA, 8-10cycle respectively, but above 7, 9KA fracture shows button type. In button fracture, shear-tensile strengths have been proportional to nugget sizes.

• Journal of Welding and Joining
• /
• v.32 no.4
• /
• pp.55-62
• /
• 2014

The use of light-weight Al alloys in the automotive industry is increasing to meet requirements for fuel efficiency and emission reduction. Joining Al alloy to the conventional steel sheet is also very important issue with the increased use of Al alloy, and several joining processes have been introduced to enhance joining strength between dissimilar metals. This paper deals with a galvanic corrosion in the dissimilar metal joining. Salt spray tests up to 2000 hours were conducted on a self-piercing rivet, spot welded, adhesive bonded and weld-bonded joints, and cross-sections and tensile shear strength according the salt spray duration were analyzed at every 500-hour. Self-piercing rivet joint had relative low initial strength but the joint strength did not change regardless of the salt spray duration. The strength of other joints (spot welded, adhesive bonded and weld-bonded joints) decreased with the increase of salt spray duration and the corrosion behaviour of each joint was discussed.

• Proceedings of the KWS Conference
• /
• 1998.10a
• /
• pp.303-304
• /
• 1998