• 한국표면공학회지
• /
• 제50권6호
• /
• pp.531-535
• /
• 2017

Enormous amount of waste oyster-shell (OS) has a major disposal problem in coastal regions. OSs have attracted much attention for recycling, because these are mainly composed of calcium carbonate with rare impurities. In this study, we demonstrate the calcareous deposit films on steel plate by using OSs on the basic of cathodic protection technique. The composition of the OSs was analyzed by wavelength dispersive X-ray fluorescence spectrometer. Carbon dioxide gas was pumped into distilled water to make carbonic acid solution for dissolution of OS. The calcareous deposit was characterized by second electron microscope (SEM), energy dispersive X-ray analysis (EDX) and X-ray diffraction. Corrosion rates were estimated by measurements of anodic polarization and immersion test. It is confirmed that calcareous deposits on steel plate are formed under all condition of cathodic protection by using waste OS from the SEM and EDX results. Calcareous deposits on steel by OS provide good corrosion resistance by acting as a barrier to oxygen supply to the steel surface.

• 소성∙가공
• /
• 제12권4호
• /
• pp.364-369
• /
• 2003

Non-heat treated steels are attractive in the steel-wire industry since the spheroidization and quenching-tempering treatment are not involved during the processing. However, non-heat treated steels should satisfy high strength and good formability without performing heat treatment. Therefore, it is important to investigate optimum materials showing a good combination of strength and formability after the drawing process. In this study, three different steels such as dual phase steel, low-Si steel, and ultra low carbon bainitic steel were used to study their mechanical properties and the cold formability. The cold formability of three steels was investigated by estimating the deformation resistance and the forming limit. The deformation resistance was estimated by calculating the deformation energy, and the forming limit was evaluated by measuring the critical strain revealing crack initiation at the notch tip of the specimens. The results showed that deformation resistance was the lowest in the low-Si steel, and the forming limit strains of ultra low carbon bainitic steel and low-Si steel were higher than that of commercial SWRCH45F steel.

• 한국산학기술학회논문지
• /
• 제13권11호
• /
• pp.5601-5609
• /
• 2012

본 논문은 포항철강공단 및 주변지역의 보건 및 환경영향 인자를 확인하기 위하여 미세먼지($PM_{10}$) 농도와 성분을 측정 및 분석하였다. 또한 지역대기자동측정망 자료를 이용하여 연별, 계절별 $PM_{10}$ 농도분포를 조사하였다. 공단지역 내 $PM_{10}$을 측정한 결과, 동일산업에서 측정된 $PM_{10}$ 평균농도는 $61.3{\pm}12.1{\mu}g/m^3$, 철강공단관리사무소에서 측정된 $PM_{10}$ 평균농도는 $44.3{\pm}8.1{\mu}g/m^3$으로 나타나 대기환경기준을 만족하였다. 공단지역 동일산업과 철강공단관리사무소에서 측정된 $PM_{10}$ 중 이차생성 이온인 ${SO_4}^{2-}$, $NO_3{^-}$, $NH_4{^+}$의 분율을 확인한 결과, ${SO_4}^{2-}$의 분율이 높게 나타났고, 황산염과 관련된 오염원이 철강공단지역에 존재하는 것으로 판단된다. 전체적으로 동일산업 지점에서는 ${SO_4}^{2-}$ > $Cl^-$ > $NO_3{^-}$ > $F^-$ > $NH_4{^+}$ 순으로 나타났고, 철강공단관리사무소 지점에서는 ${SO_4}^{2-}$ > $Cl^-$ > $NO_3{^-}$ > $NH_4{^+}$ > $F^-$ 순으로 나타났다.

• 한국해양공학회지
• /
• 제31권5호
• /
• pp.364-370
• /
• 2017

A numerical model based on the mode superposition method is used to study the vortex-induced vibration response characteristics of a deep-sea riser such as steel catenary riser (SCR). A steel catenary riser can be modeled using a flexible cable with simple supports at both ends. The natural frequency, mode shape and mode curvature of the riser are calculated and the vortex-induced vibration response of the riser is obtained using the equilibrium of the input and output power. The mode superposition method is applied to the vibrational stresses for each mode to calculate the overall riser fatigue life.

• 한국산업융합학회 논문집
• /
• 제15권1호
• /
• pp.29-36
• /
• 2012

Reinforced concrete shear walls and X-type steel braces were applied in seismic retrofit techniques for seismic performance evaluation of school buildings constructed in accordance with standard design announced by the ordinance of the ministry of construction in 1980s. Seismic performance evaluation was based on FEMA 356 using response spectrum as elastic analysis and conducted to pushover analysis with nonlinear static analysis. The maximum displacement ratio between floors in 4th and 3rd floors of the existing school buildings was less than 1.0%, which was functioning level in FEMA 356. However, because plastic hinge occurs somewhat in structural members according to the results of pushover analysis, partial reinforcement will be required. X-direction of the maximum lateral displacement of reinforced concrete shear walls than X-type steel braces was 45% and 32% in 4th and 3rd floors of school buildings, and Y-direction was 18% and 17%, respectively.

• 한국산업융합학회 논문집
• /
• 제20권1호
• /
• pp.81-87
• /
• 2017

In order to reduce the weight of the blow motor case and to maintain the strength of the motor joint, the mechanical joining strength is to be predicted. The true stress - true strain curves for finite element analysis were obtained through tensile tests of HGI and DP 780 steel. The mechanical joining strength was predicted through an explicit finite element analysis and the accuracy of the predicted results was verified by actual sample test. The regression equation for predicting the mechanical joining strength to the thickness of the DP 780 steel was derived. The minimum thickness of DP 780(1.2mm), which is equivalent to the joining strength of HGI(2.6mm), was derived from the equation.

• 기술혁신학회지
• /
• 제4권3호
• /
• pp.369-382
• /
• 2001

In this research, the world top steel companies' technical changes were measured by the nonparametric Malmquist index. Steel industry's production frontier which was composed of multiple inputs and multiple outputs was defined by using real data of the companies from 1986 to 1998, and then the variability of technical progress(or regress) was analyzed during that period. The dynamics of individual steel companies\` technical changes, periodical technical changes, and each country's technical chanties were explained. A matrix which was based on technical chanties, technical efficiency changes, and scale efficiency changes was designed to assist to find out current position and In build up future strategies. This research results will be an valuable input to the early stage of formulating competitive strategy because the technical core capability is an important source of the each companies's competitiveness.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.155-158
• /
• 2007

The construction industry kept lower level of the technology and productivity improvement than any other kinds of industry. But in most analysis of previous construction work which promoted the productivity of construction, the analysis process has only developed by the economical efficiency or the time studies through work sampling in construction field, So We suggest motion analysis as a tool to solve these problems. Spacially, this study find out productivity improvement method of steel frame fabrication works with using motion analysis. If the result of this study were to be applied to the actual construction field, it will be of great help for Building Construction Automation.

• 한국해양공학회지
• /
• 제18권2호
• /
• pp.70-76
• /
• 2004

In the steel marking industry, most companies have adapted the continuous casting process, due to its economical benefit. Casting rolls are utilized for frictional drive and the transport of solidifying slap. Dimensional tolerances, mechanical stability, and surface condition of the casting rolls can affect both the surface and the internal quality of the product being cast. To overcome these problems, the industry now is focused on accelerating the rate of technological improvements. This study has been undertaken for the development of casting rolls overlaid materials (SAW FCW wire), with the addition of Vanadium and Molybdenum to the martensitic stainless steel, in order to increase tensile strength and hardness at elevated temperatures.

• 산업공학
• /
• 제14권2호
• /
• pp.198-204
• /
• 2001

The ISO 9000 family of international quality management standards were revised on 15 December 2000. The ISO 9001:2000 standard is used for certification/registration and contractual purposes by organizations seeking recognition of their quality management system(QMS). We summarize key contents changed in ISO 9000:2000 family standards. To comply with ISO 9001:2000, we analyze the current QMS for steel outfit industry, using audit results from ISO 9001:1994 for seven steel outfit firms during last three years. We investigate statistical relationships between ISO 9001:2000 and ISO 9001:1994 requirements from a three dimensional contingency table with audit results. We observe that the importance of requirements of the ISO 9001:2000 sections makes a difference between companies.