• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1416-1422
• /
• 2010

Monorail has been classified as straddled type and suspended type. However, Inchon Wolmi Eunha rail, a center guide type first ever introduced in the world, uses a new concept Y-Beam as guide rail. Since Y-Beam takes horizontal loads of monorail through guide wheels, it is an essential structure for the safe operation along with concrete surface and steel beam which take vertical loads through main tires. This study presents the characteristic and reliability of Y-Beam and Y-Beam fixture, clamp, which are not only taking horizontal loads but also guarantying both guiding and stability of monorail and holding power supply line.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.3
• /
• pp.17-22
• /
• 1999

The effect of microwave irradiation on wood bending was investigated in this study. The specimens irradiated with microwave were bent around a form by using pedestal-steel and clamps. The specimens, korea red pine (Pinus densiflora), for this test were water-soaked for 78 hours. Saturated specimens were boiled in water for an hour. The size of specimens was 350mm(L) by 20mm(R) by 10mm(T). These specimens were heated by microwave of 2,450MHz. The most suitable time for microwave irradiation seems to range from 60 to 90 seconds. Wood moisture content decreased remarkably with the increase of irradiation time. When a softened wood piece is bent, its convex side was stretched while the concave side was compressed. It can be compressed considerably, but stretched very little. Therefore the failure will be governed by the tensile breaking strain and occur mainly on the convex face. So we obtained results from three different bending process methods as follows : 1) When bending with a pedestal-steel, convex face had not tensile breakings, but concave face had compression fails. 2) When bending with a clamp, bending time increased more than pedestal-steel and occurred tensile breaking. 3) Bending with a pedestal-steel and a clamp was found to be the most excellent operation method in this study.

• Journal of Power System Engineering
• /
• v.9 no.3
• /
• pp.71-78
• /
• 2005

A high-pressure hose includes rebar layers of the synthetic fiber such as nylon or a steel wire to control internal pressure. The hose assembly is manufactured through the swaging process to clamp the hose into the metal fittings. Usually, the hose behavior is affected by the resultant of the longitudinal and circumferential forces produced by the internal pressure. The rebar layers can appear the most ideal rebar effect when they are arranged to the same direction as the resultant force. The braid angle applied in the rebar layers is an important factor in determining ultimate burst pressure and overall hose life. Failure can occur on the contacted parts of a hose with the metal fittings under severe operating conditions such as high pressure and temperature of the inner fluid. In this paper, the mechanical behavior between the hose and the metal fittings during the swaging process and the stress variation characteristics of a high-pressure hose under a constant applied pressure are analyzed with respect to the braid angle of steel wire using the finite element method.

• Steel and Composite Structures
• /
• v.31 no.3
• /
• pp.261-276
• /
• 2019

The study investigates the free vibration of a nano-scale sandwich beam by an extended high order approach, which has not been reported in the existing literature. First-order shear deformation theory for steel skins and so-called high-order sandwich panel theory for the core are applied. Next, the modified couple stress theory is used for both skins and cores. The Hamilton principle is utilized for deriving equations and corresponding boundary conditions. First, in the study the three-mode shapes natural frequencies for various material parameters are investigated. Also, obtained results are evaluated for two types of stiff and soft cores and isotropic, homogenous steel skins. In the research since the governing equations and also the boundary conditions are nonhomogeneous, therefore some closed-form solutions are not applicable. So, to obtain natural frequencies, the boundary conditions are converted to initial conditions called the shooting method as the numerical one. This method is one of the most robust approaches to solve complex equations and boundary conditions. Moreover, three types of simply supported on both sides of the beam (S-S), simply on one side and clamp supported on the other one (S-C) and clamped supported on both sides (C-C) are scrutinized. The parametric study is followed to evaluate the effect of nano-size scale, geometrical configurations for skins, core and material property change for cores as well. Results show that natural frequencies increase by an increase in skins thickness and core Young modulus and a decrease in beam length, core thickness as well. Furthermore, differences between obtained frequencies for soft and stiff cores increase in higher mode shapes; while, the more differences are evaluated for the stiff one.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.05a
• /
• pp.325-328
• /
• 2008

This paper presents a new conceptual electromagnetic induction eddy current-based stainless steel plate spiral type heater for heat exchanger or dual packs Heater in hot water system boiler steamer and super heated steamer, which is more suitable and acceptable for new generation consumer power applications. In addition, an active clamped quasi resonant PWM high frequency inverter using trench gate IGBTs power module can operate under a principle of zero voltage soft commutation with PWM is developed and demonstrated fora high efficient induction heated hot water system and boiler in the consumer power applications This consumer induction heater power appliance using active clamp soft switching PWM high-frequency inverter is evaluated and discussed on the basis of the simulation and experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.518-519
• /
• 2007

In this paper, the temperature distribution within ACSR conductor was precisely measured and examined, conducted as part of a serious of studies on large currents in transmission lines. According to measurements of the conductor temperature near a joint(sleeve and clamp), the electrical resistance of joint is lower than that of the same length conductor. The detailed results were presented in the text.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.491-494
• /
• 2003

This paper presents a new conceptual electromagnetic induction eddy current-based stainless steel plate spiral type heater for heat exchanger or Dual Packs Heater in hot water producer, boiler steamer and super heated steamer, which is more suitable and acceptable for new generation consumer power applications. In addition, all active clamped edge resonant PWM high frequency inverter using trench gate IGBTs power module can operate under a principle oi zero voltage soft communication with PWM is developed and demonstrated for a high efficient Induction heated hot water producer and boiler in the consumer power applications. This consumer induction heater power appliance using active clamp soft switching PWM high frequency inverter is evaluated and discussed on the basis of the simulation and experimental results.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.2
• /
• pp.165-173
• /
• 2009

Hanger cables in suspension bridges are constrained by the horizontal clamp. So, the accuracy of estimated tension of hange cable using existing methods based on the simple mathematical model of singel cable decreases as the length of cable decreases because of the flexural rigidity. Therefore, back analysis and system identification techniques based on the finite element model are proposed recently. In this paper, the applicability of the back analysis and system identification techniques are compared using the hanger cable of Gang-An Bridge. The experimental results show that the back analysis and system identification techniques are more reliable than the existing string theory and linear regression method in the view point of the error of natural frequencies. However, the estimation error of tension can be varied according to the accuracy of finite element model in the model based methods. Especially, the boundary condition is more affective when the length of cable is short, so it is important to identify the boundary condition through experiment if it is possible. The tension estimation method using system identification technique is more attractive because it can easily consider the boundary condition and it is not sensitive to the number of input measured natural frequencies.

• Fire Science and Engineering
• /
• v.30 no.4
• /
• pp.121-127
• /
• 2016

This study analyzed the structural and electrical characteristics of an iron fittings type Corrugated Stainless Steel Tubing (CSST) damaged by the Primary Current Injection Test System (PCITS). CSST consists of cladding, tube, nuts, clamp ring, flare cap, socket, and ball valve. For an evaluation of the dielectric withstand voltage, the area between the live part and non-live part of the CCST shall withstand a voltage of 220 V AC for one minute. For an evaluation of the insulation performance by 500 V DC, it is required that the insulation exceed more than $1M{\Omega}$ before the temperature rise test, $0.3M{\Omega}$ after the test. Although the average resistance of the product was $11.5m{\Omega}$, that of the product damaged at a current of 130 A by the PCITS was $11.50m{\Omega}$. Furthermore, parts of the cladding were melted and black smoke appeared when a current of 130 A applied for 10 s. After 60 s, most parts were heated and turned red. At 120 s, the parts that turned red had widened. Although it did not form a normal distribution because the P value was 0.019 with a confidential interval of 95%, it revealed outstanding characteristics with an AD (Anderson-Darling) value of 0.896 and a standard deviation of 0.5573.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.353-366
• /
• 2012

This study was interpreted the making techniques of the Four Guardian Statues in Wanju Songkwangsa Temple, and retained basic data necessary for conservation treatment and restoration of the same material by estimating the soil source. The molding clay used in the Statues showed a variety of material characteristics according to different layers. The first and mid layers estimated as the original molding clay are composed of the same kind of soil. The soil of the finish layer was also confirmed to be genetically similar to that of the first and mid layers, despite little discrepancy. The former restoration layer was inconsistent in material characteristics with the original molding clay in every result of analysis. As a result of gamma radiography, making techniques of the Statues were able to identify the figure of the frame connecting the woods of main pillar frame to sub-frame and steel wire with ㄷ-clamp, nails and straw ropes, and the molding clay constructed upon the frame. Meanwhile, provenance interpretation confirmed that the soil of the estimated provenance area is of the same origin as the soil of the finish layer, and therefore is an appropriate material for conservation treatment. This result will contribute to the research on making techniques of the molding clay Statues.