• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.74-81
• /
• 2004

In this study, static end loading tests with load transfer measurement were accomplished for large diameter drilled shaft constructed in fault zone. Yield pile capacity (or ultimate pile capacity) from load-settlement curve was determined and axial load transfer behavior was measurd. The end bearing capacity was increased 2 times due to grouting the toe ground under pile base.

• 한국지반공학회논문집
• /
• 제20권5호
• /
• pp.135-143
• /
• 2004

해상교량건설 현장의 육상구간에서 예기치 않게 발견된 단층파쇄대에 시공된 대구경 현장타설말뚝의 선단지지력을 확인하기 위하여 양방향 선단재하시험을 실시하였다. 본 연구의 목적은 단층파쇄대에 시공된 대구경 현장타설말뚝에 재하시험을 실시하여 단층파쇄대에서의 선단지지력을 확인하고, 그 후 말뚝 선단 하부지반에 보강 그라우팅을 실시하여 선단보강에 의한 선단지지력 증가효과를 확인하는 것이다. 선단보강 그라우팅 후 선단지지력은 2배 이상 증가하였으며 보강전 보다 선단의 침하량이 현저하게 줄어드는 것을 확인할 수 있었다.

• Journal of Biosystems Engineering
• /
• 제41권3호
• /
• pp.153-160
• /
• 2016

Purpose: This study was conducted to experimentally investigate the structural safety of and identify critical locations in a front-end loader under impact loads. Methods: Impact and static tests were conducted on a commonly used front-end loader mounted on a tractor. In the impact test, the bucket of the front-end loader with maximum live load was raised to its maximum lift height and was allowed to free fall to a height of 500 mm above the ground where it was stopped abruptly. For the static test, the bucket with maximum live load was raised and held at the maximum lift height, median height, and a height of 500 mm from the ground. Strain gages were attached at twenty-three main locations on the front-end loader, and the maximum stresses and strains were measured during respective impact and static tests. Results: Stresses and strains at the same location on the loader were higher in the impact test than in the static test, for most of measurement locations. This indicated that the front-end loader was put under a severe environment during impact loading. The safety factors for stresses were higher than 1.0 at all locations during impact and static tests. Conclusions: Since the lowest safety factor was higher than 1.0, the front-end loader was considered as structurally safe under impact loads. However, caution must be exercised at the locations having relatively low safety factors because failure may occur at these locations under high impact loads. These important design locations were identified to be the bucket link elements and the connection elements between the tractor frame and front-end loader. A robust design is required for these elements because of their high failure probability caused by excessive impact stress.

• 한국구조물진단유지관리공학회 논문집
• /
• 제10권4호
• /
• pp.183-193
• /
• 2006

본 연구는 탄소섬유시트로 보강된 철근콘크리트 보에 정적하중과 반복하중이 작용할 때의 거동을 다루고 있다. 탄소섬유시트로 보강된 RC보의 정적실험 결과를 기준으로 반복하중 실험을 수행하였다. 반복하중 실험의 변수는 탄소섬유시트 겹수, 단부 U밴드 유무, 반복하중 재하속도 등이 있다. 실험결과를 통해 단조증가하중과 반복하중 하에서의 에너지 소산량과 휨 강성의 변화, 연성특성, 강도특성, 휨 거동 등을 고찰하며, 또한 탄소섬유시트의 파단변형률을 평가하였다. 본 연구에서는 반복하중 실험 결과를 바탕으로 탄소섬유시트로 보강된 RC보의 정적 및 동적 휨 보강 해석 및 설계에 필요한 기초자료를 제시하고자 한다.

• International Journal of Concrete Structures and Materials
• /
• 제1권1호
• /
• pp.45-55
• /
• 2007

Ten beams bonded with glass fiber reinforced polymer (GFRP) laminates were tested under cyclic loading with the load range and the FRP reinforcement ratio as test parameters. The maximum load level during cyclic loading was 55%, 65% and 75% of the static flexural strength while the minimum load level was kept constant at 35%. Deflections of the beams at the end of 525000 cycles were found to increase by 16% and 44% when the maximum load level was increased from 55% to 65% and 75% of the static flexural strength, respectively. Beams with FRP reinforcement ratios of 0.64% and 1.28% were found to exhibit lesser deflections of about 15% and 20%, respectively, compared to a similar beam without FRP reinforcement. An analytical approach based on cycle-dependent effective moduli of elasticity of concrete and FRP reinforcement is presented and found to predict the deflections of the test beams well.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.421-426
• /
• 2009

Recently, the design process for a railway bogie frame in Europe has been carried out according to the norm EN 13749. The activities in the norm EN shall demonstrate that the design of the bogie frame fulfills the acceptances of 4 steps of the program such as structural calculation, static tests, fatigue test and on-tracks tests. At the end of the acceptance program, the on-tracks tests have the aim to measure the real stress history generated in operation and to verify that they are reasonably next to those calculated and measured on the test rig. Therefore, in order to assure the safety of the railway vehicle, it is important to examined the durability of that under load histories measured from on-tracks tests. In this study, under variable amplitude loading based on the actual acceleration history, fatigue analysis of the welding bogie frame is investigated by using durability software. Moreover, the fatigue life of the frame under the loading in the norm EN fatigue test condition is evaluated and compared with the life under variable amplitude loading.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.544-551
• /
• 2004

Piles are structural elements made of steel, concrete or timber, and utilize as pile foundation which is one of deep foundations. Driven pile among them, which drives pile into the ground, is fast-constructable, less expensive and it supplies much bearing capacity. For these reasons, its demand is steady. In this study, by selecting the cases which reached ultimate failure during in-situ static loading tests, bearing capacities acquired from these tests were compared with those computed by existing theories and formula. As the results of the analysis, ultimate bearing capacity computed by theoretic formula were less or similar to those of test results in most cases, but lower ground water level and more dense layer where end of piles were reached remarkably high bearing capacity in theoretical methods. ${\beta}-method$ and Korean structure foundation design standard were sensitive to ground physical properties. Meyerhof metbod and API code were relatively independent from site condition.

• 콘크리트학회논문집
• /
• 제29권4호
• /
• pp.371-378
• /
• 2017

본 연구에서는 철근콘크리트 아치 데크의 정적재하실험을 통해 휨 거동을 평가하였다. 휨 실험은 길이 2.5 m, 폭 1.2 m, 중심단면 두께 100 mm, 단부단면 두께 160 mm의 실제 크기 프리캐스트 철근콘크리트 아치 데크의 정적재하 실험을 실시하였다. 실험결과는 극한설계강도에 비하여 약 1.74배 높은 하중을 견디는 것으로 관찰되었다. 반면, 실험체에는 구간에 따라 각각 다른 거동이 관찰되었다. 이러한 거동은 아치 데크와 이를 지지하는 반력대 사이에 일체거동이 이뤄지지 않은 이유로 인한 것으로 판단되었다. 그러므로 추후 연구에서는 반력대를 제외한 아치 데크의 정적재하 실험을 통해 정밀한 거동을 확인해야 할 것으로 사료된다. 실험결과를 종합하여 보면, 철근콘크리트 아치 데크는 일반형태의 바닥판에 비하여 우수한 구조적 이점을 통해 설계기준보다 높은 구조성능을 나타내었다. 이를 통해, 향후에는 장지간 바닥판으로써의 활용이 가능할 것으로 사료된다.

• Steel and Composite Structures
• /
• 제22권1호
• /
• pp.45-61
• /
• 2016

The domestic and foreign scholars conducted many studies on mechanical properties of wave web steel beam and high-strength spiral stirrups confined concrete columns. Based on the previous research work, studies were conducted on the anti-seismic property of the end plate bolt connected wave web steel beam and high-strength spiral stirrups confined concrete column nodes applied with pre-tightening force. Four full-size node test models in two groups were designed for low-cycle repeated loading quasi-static test. Through observation of the stress, distortion, failure process and failure mode of node models, analysis was made on its load-carrying capacity, deformation performance and energy dissipation capacity, and the reliability of the new node was verified. The results showed that: under action of the beam-end stiffener, the plastic hinges on the end of wave web steel beam are displaced outward and played its role of energy dissipation capacity. The study results provided reliable theoretical basis for the engineering application of the new types of nodes.

• Structural Engineering and Mechanics
• /
• 제49권6호
• /
• pp.775-792
• /
• 2014

Static loading tests were carried out in this study to investigate the effect of bar cutoff on the resistance of RC beam-column sub-assemblages under column loss. Two specimens were designed with continuous main reinforcement. Four others were designed with different types of bar cutoff in the mid-span and/or the beam-end regions. Compressive arch and tensile catenary responses of the specimens under gravitational loading were compared. Test results indicated that those specimens with approximately equal moment strength at the beam ends had similar peak loading resistance in the compressive arch phase but varied resistance degradation in the transition phase because of bar cutoff. The compressive bars terminated at one-third span could help to mitigate the degradation although they had minor contribution to the catenary action. Among those cutoff patterns, the K-type cutoff presented the best strength enhancement. It revealed that it is better to extend the steel bars beyond the mid-span before cutoff for the two-span beams bridging over a column vulnerable to sudden failure. For general cutoff patterns dominated by gravitational and seismic designs, they may be appropriately modified to minimize the influence of bar cutoff on the progressive collapse resistance.