• Journal of the Korean Vacuum Society
• /
• v.12 no.3
• /
• pp.162-167
• /
• 2003

To find the concentration according to the depth-direction of ions implanted in the sample, with sputtering of the sample surface, one needs the depth profiling of ion implanted in the sample. On measuring of depth profiling, the sputtering rate to affect depth direction, is calculated by SRIM simulation. When ion is implanted in the sample, the atomic density of the sample rises up a little, and it alters sputtering yield. This alteration then causes differences of sputtering rate to affect depth-direction, on measuring of depth profiling. With the usage of SRIM Monte Carlo simulation code, one calculates sputtering rate, with sputtering yield by the alteration of atomic density of the sample through ion implantation. As a result, it goes to prove that its difference affects depth distribution, on measuring of depth profiling.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.1
• /
• pp.11-14
• /
• 2004

An rf triode magnetron sputtering system is designed and installed its construction in vacuum chamber. In order to calibrate the rf triode magnetron sputtering for thin films deposition processes, the effects of different glow discharge conditions were investigated in terms of the deposition rate measurements. The basic parameters for calibrating experiment in this sputtering system are rf power input, gas pressure, plasma current, and target-to-substrate distance. Because a knowledge of the deposition rate is necessary to control film thickness and to evaluate optimal conditions which are an important consideration in preparing better thin films, the deposition rates of copper as a testing material under the various sputtering conditions are investigated. Furthermore, a triode sputtering system designed in our team is simulated by the SIMION program. As a result, it is sure that the simulation of electron trajectories in the sputtering system is confined directly above the target surface by the force of E${\times}$B field. Finally, some teats with the above 4 different sputtering conditions demonstrate that the deposition rate of rf triode magnetron sputtering is relatively higher than that of the conventional sputtering system. This means that the higher deposition rate is probably caused by a high ion density in the triode and magnetron system. The erosion area of target surface bombarded by Ar ion is sputtered widely on the whole target except on both magnet sides. Therefore, the designed rf triode magnetron sputtering is a powerful deposition system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.787-790
• /
• 2003

A rf triode magnetron sputtering system is designed and installed its construction in vacuum chamber. In order to calibrate the rf triode magnetron sputtering for thin films deposition processes, the effects of different glow discharge conditions were investigated in terms of the deposition rate measurements. The basic parameters for calibrating experiment in this sputtering system are rf power input, gas pressure, plasma current, and target-to-substrate distance. Because a knowledge of the deposition rate is necessary to control film thickness and to evaluate optimal conditions which are an important consideration in preparing better thin films, the deposition rates of copper as a testing material under the various sputtering conditions are investigated. Furthermore, a triode sputtering system designed in our team is simulated by the SIMION program. As a result, it is sure that the simulation of electron trajectories in the sputtering system is confined directly above the target surface by the force of $E{\times}B$ field. Finally, some teats with the above 4 different sputtering conditions demonstrate that the deposition rate of rf triode magnetron sputtering is relatively higher than that of the conventional sputtering system. This means that the higher deposition rate is probably caused by a high ion density in the triode and magnetron system. The erosion area of target surface bombarded by Ar ion is sputtered widely on the whole target except on both magnet sides. Therefore, the designed rf triode magnetron sputtering is a powerful deposition system.

• Korean Journal of Materials Research
• /
• v.16 no.8
• /
• pp.461-465
• /
• 2006

Chromium (Cr) films were deposited on plain carbon steel sheets by DC and RF magnetron sputtering as well as by electroplating. Effects of DC or RF sputtering power on the deposition rate and properties such as, hardness, surface roughness and corrosion-resistance of the Cr films were investigated. X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microcopy (SEM) analyses were performed to investigate the crystal structure, surface roughness, thickness of the Cr films. Salt fog tests were used to evaluate the corrosion resistance of the samples. The deposition rate, hardness, and surface roughness of the Cr film deposited by either DC or RF sputtering increase with the increase of sputtering power but the adhesion strength is nearly independent of the sputtering power. The deposition rate, hardness, and adhesion strength of the Cr film deposited by DC sputtering are higher than those of the Cr film deposited by RF sputtering, but RF sputtering offers smoother surface and higher corrosion-resistance. The sputter-deposited Cr film is harder and has a smoother surface than the electroplated one. The sputter-deposited Cr film also has higher corrosion-resistance than the electroplated one, which may be attributed to the smoother surface of the sputter-deposited film.

• Korean Journal of Materials Research
• /
• v.15 no.10
• /
• pp.621-625
• /
• 2005

Effects of rf power, pressure, sputtering gas composition, and substrate temperature on the deposition rate of the $WC_x$ coatings were investigated. The effects of rf power and sputtering gas composition on the hardness and corrosion resistance of the $WC_x$ coatings deposited by reactive sputtering were also investigated. X-ray diffraction (XRD) and Auger electron spectroscopy (AES) analyses were performed to determine the structures and compositions of the films, respectively. The hardnesses of the films were investigated using a nanoindenter, scanning electron microscopy, ana a salt-spray test, respectively. The deposition rate of the films was proportional to rf power and inversely proportional to the $CH_4$ content of $Ar/CH_4$ sputtering gas. The deposition rate linearly increased with increasing chamber pressure. The hardness of the $WC_x$ coatings Increased as rf power increased. The highest hardness was obtained at a $Ar/CH_4$ concentration of $10 vol.\%$ in the sputtering gas. The hardness of the $WC_x$ film deposited under optimal conditions was found to be much higher than that of the electroplated chromium film, although the corrosion resistance of the former was slightly lower than that of the latter.

• Fashion & Textile Research Journal
• /
• v.8 no.1
• /
• pp.129-133
• /
• 2006

To develope a high value-added fiber products which is useful in the human body physiology, the Macban stone was deposited on the PET fabric by sputtering and its effects were investigated. Then, a Macban stone target was prepared for sputtering treatment and treated on the PET fabric by RF sputtering process. After treatment, surface observation by SEM, far-infrared emissivity and emissive power, the fastness to washing and light, bacteriostatic rate, electrostatic, drape stiffness, and breaking strength of PET fabric were investigated. From these investigation, the following conclusions were obtained. 1) The Macban stone was able to deposit on the PET fabric, by the RF sputtering treatment which is eco-friendly dry textile finishing. 2) The far-infrared emissivity and emissive power of sputtered PET fabrics were increased. 3) When PET fabric was treated by sputtering with Macban stone, the amount of deposited Macban stone increased with increasing treatment time and it was deposited on the fabric surface firmly. 4) The bacteriostatic rate of sputtered PET fabrics was about 20%. 5) The electrostatic charge of fiber surface was reduced by sputtering. 6) The fastness washing to light of dyed fabric were improved by the deposition of Macban stone, but the breaking strength was not changed by sputtering. 7) The drape stiffness of sputtered PET fabrics increased with increasing treatment time.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.110-113
• /
• 2006

A high rate deposition sputtering process of magnesium oxide thin film in oxide mode has been developed using a 20 kW unipolar pulsed power supply. The power supply was operated at a maximum constant voltage of 500 V and a constant current of 40 A. The pulse repetition rate and the duty were changed in the ranges of $10\sim50$ kHz and $10\sim60%$, respectively. The deposition rate increased with rising incident power to the target. Maximum incident power to the magnesium target was obtained by the control of frequency, duty and current. The deposition rate of a moving state was 9 nm m/min at the average power of 1.5 kW. This result shows higher deposition rate than any other previous work involving reactive sputtering in oxide mode. The thickness uniformities over the entire substrate area of $982mm{\times}563mm$ were observed at the processing pressure of $2.8\sim9.5$ mTorr. The thickness distribution was improved at lower pressure. This technique is proposed for application to a high through-put sputtering system for plasma display panels.

• Journal of the Korean Ceramic Society
• /
• v.33 no.4
• /
• pp.441-447
• /
• 1996

Sb doped SnO2(ATO:Antinomy doped Tin Oxide) thin films were prepared by a DC magnetron spttuering method using oxide target and the deposition characteristics were investigated. The experimental conditions are as follows :Ar flow rate : 100 sccm oxygen flow rates ; 0-100 sccm deposition temperature ; 250 -40$0^{\circ}C$ DC sputter powder ; 150~550 W and sputtering pressure ; ; 2~7 mTorr. Deposition rate greatly depends not on the deposition temperature but on the reaction pressure oxygen flow rate and sputter power,. when the sputter powder is low ATO thin films with (110) preferred orientation are deposited. And when the sputter power is high (110) prefered orientation appeares with decreasing of oxygen flow rate and increasing of suputte-ring pressure.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.13-14
• /
• 2008

A high rate magnetron sputtering source (HRMSS) was employed to deposit thick copper films. The HRMSS was manufactured by changing the magnet size, arrangement, and field intensity. For the preparation of thick copper films, the copper sputtering conditions using HRMSS were characterized based on the deposition parameters such as discharge characteristics, I-V characteristics of the source, and change of deposition rate. The deposition rate of copper turned out to be more than 5 times than that of conventional magnetron sputtering source. Thick copper films having thickness of more than $20{\mu}m$ were prepared by using HRMSS. The morphology and orientation of the films were investigated by scanning electron microscopy and x-ray diffraction.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.376-376
• /
• 2010

이차이온질량분석기(SIMS)는 수 kV의 에너지를 갖는 일차이온($O_2^+$, $Cs^+$)을 시료표면에 충돌시켜 표면에서 떨어져 나온 이온의 질량 및 개수를 분석하는 장비이다. SIMS는 성분원소의 깊이분포도 측정, 질량분석, Image mapping등 다양한 분석을 할 수 있다. 특히 극미량 분석이나 깊이분포도 분석에서 가장 뛰어난 성능을 가지고 있어 아직까지 많이 사용하고 있다. 하지만 SIMS는 이온빔을 이용한 스퍼터링(Sputtering) 방법으로 분석을 하므로 파괴적이며 매질효과가 심하다. 또한 Matrix 물질의 함량이나 물질 자체가 변한다면 Sputtering rate도 그에 따라 변하게 된다. 이러한 현상에 의해 Sputtering rate는 다른 물질이 섞여 있는 경우 Sputtering rate이 빠른 물질이 먼저 Sputtering이 되는 Preferential Sputtering 현상이 나타나기 때문에 계면에서 깊이분해능에 좋지 않은 영향을 주게 된다. 본 연구에서는 SIMS로 Si(100) 기판 위에 약 100nm 두께로 Fe가 증착된 시료를 분석하였다. 이차이온으로 $O_2^+$이온을 사용하였으며 이온의 입사각을 변화시켜 각 조건에서 생기는 Fe 표면의 Topograph을 SEM으로 관찰하였으며, Topograph와 SIMS깊이분해능의 관계을 이해하고 $O_2^+$ 이온의 입사각 변화에 따른 Fe 표면의 Topograph의 형태와 산화도를 이해하고자 한다.