• Journal of Pharmaceutical Investigation
• /
• 제38권6호
• /
• pp.381-385
• /
• 2008

Isosorbide dinitrate is an oral assiatant therapy agent of angina pectoris, myocardial infarction and congestive heart failure. The objective of this study was to formulate sustained release containing isosorbide dinitrate and assess their formulation variables. Pellets were prepared by fluid bed process and consist of drug layer and membrane layer. The pellets were coated with ethylcellulose along with $5{\sim}15%$ of plasticizer such as triacetin and diethyl butylrate. In vitro evaluation study was performed by comparative dissolution test between test and reference isosorbide dinitrate preparation. We could prepare sustained pellets of isosorbide dinitrate by fluid bed process which were reduced process time and had high content. The pellet coated with 1% ethylcellulose and triacetin(l5%) had a similar dissolution behavior compare to reference isosorbide dinitrate preparation controlling initial dissolution and those of dissolution at 30 min were 17.25 and 17.09%, respectively. Difference factor and similarity factor were $0{\sim}15$ and $50{\sim}100$ and there was no significant difference in bioequivalence between formulations. It might be concluded that our sustained release pellet of isosorbide dinitrate could be an alternatively delivery system to reference drug preparation.

• 열처리공학회지
• /
• 제13권2호
• /
• pp.98-102
• /
• 2000

The effect of vacuum heat treatment in the thermal sprayed ceramics coating on a capstan by either high velocity oxygen fuel(HVOF) or plasma thermal spray process was investigated. The coating materials applied on the capstan were tungsten and chrome carbides. In order to characterize the interface between coating layer and bare materials, hardness, adhesion strength, X-ray diffraction(XRD) and microstructural analysis are conducted. The adhesion strength of the carbide coated materials by HVOF process is over 500MPa compared to those of plasma coating process is 230MPa. In case of the carbide coated materials by HVOF process, the adhesion strength is increased to 15MPa and the porosity is reduced under 5% by vacuum heat treatment for 5 hrs at $1000^{\circ}C$. The XRD results reveal that the increasement is believed due to the phase stabilization of metastable $Cr_3C_2$ phase to stable $Cr_{23}C_6$ phase.

• Corrosion Science and Technology
• /
• 제8권4호
• /
• pp.157-161
• /
• 2009

The corrosion resistance of reinforcing bar was studied to endure the marine environment during shipment. The red rust on the surface did not damage the adherence in the concrete structures, especially in highly alkaline environment, but made the consumer doubt of the quality. The passivation process by alkalization of the quenching water in the tempcore process failed to endure the long shipping period. The ceramic coating by sol-gel process improved the corrosion resistance without damaging the mechanical properties and adherence between concrete and reinfiorcing bar. Optimal concentration of the coating solution and coating temperature were tested. No additional energy was necessary for the coating process by spraying during cooling process, resulting simplified process and low cost. Salt spray test, cyclic corrosion test and atmospheric test were employed to confirm the resistance. The corrosion rates were presented by rating number and polarization resistance. The coating layer was examined by FIB, XRD and SEM etc.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.254-255
• /
• 2006

Powder library of pseudo four components Li-Ni-Co-Ti compounds were prepared for exploring the composition region with the single phase of the layer-type structure by using combinatorial high-throuput preparation system "M-ist Combi" based on electrostatic spray deposition method. The new layer-type compounds were found wider composition region than the previous report. This process is promising way to find multi component functional materials.

• 마이크로전자및패키징학회지
• /
• 제13권3호
• /
• pp.33-38
• /
• 2006

유리 조성이 섞인 유전체 파우더와 증류수 그리고 해교제의 혼합으로 만들어진 슬러리를 에어로졸 형태로 고압 스프레이 건으로 기판에 스프레이 코팅 하였다. 기판으로는 알루미나 기판과 전극 패턴이 프린트 된 그린쉬트를 사용하였다. 슬러리 점도와 스프레이 건에 의한 분사모양 그리고 슬러리의 분사량은 코팅 층의 코팅 속도에 영향을 끼쳤으나 밀도에는 거의 영향을 주지 않았다. 고압 스프레이 코팅 방법은 기판에 직접적인 가압 과정이 없으므로 내부 전극은 인쇄된 형태가 유지되었다. 최적 조건에서는 균일하고 조밀한 코팅 층을 얻을 수 있었다. 또한 그린쉬트에 적층 공정을 사용한 기존의 방법과는 달리 고압 스프레이 코팅 방법은 $20{\sim}50{\mu}m$의 얇은 유전체 층을 얻을 수 있었다.

• 한국결정성장학회지
• /
• 제9권1호
• /
• pp.55-59
• /
• 1999

초임계 분출법을 이용하여 입자의 코팅을 행하였다. 핵입자로는 분무건조법으로 제조된 Microcapsule을 사용하였으며, 코팅 물질로는 녹는 점이 다른 두 종류의 파라핀을 사용하였다. 파라핀이 녹아 있는 초임계 $CO_{2}$ 용액은 공 기에 의해 유통중인 유통층 내부로 작은 직경의 노즐을 통해 분출된다. 이 때 추출조의 온도와 압력은 각각 $50~120^{\circ}C$, $150~200\;kg/\textrm{cm}^2$으로 변화시켰다. 이론적인 코팅 두께를 계산하였으며, 코팅층의 분석은 SEM과 FT-IR을 사용하였다. $Mg^{2+}$ ion의 용출특성은 원자홉광광도계를 사용하여 조사하였다.

• 한국재료학회지
• /
• 제25권3호
• /
• pp.125-131
• /
• 2015

Fluorine-doped $SnO_2$ (FTO) thin film/Ag nanowire (NW) double layers were fabricated by means of spin coating and ultrasonic spray pyrolysis. To investigate the optimum thickness of the FTO thin films when used as protection layer for Ag NWs, the deposition time of the ultrasonic spray pyrolysis process was varied at 0, 1, 3, 5, or 10 min. The structural, chemical, morphological, electrical, and optical properties of the double layers were examined using X-ray diffraction, X-ray photoelectron spectroscopy, field-emission scanning electron microscopy, transmission electron microscopy, the Hall effect measurement system, and UV-Vis spectrophotometry. Although pure Ag NWs formed isolated droplet-shaped Ag particles at an annealing temperature of $300^{\circ}C$, Ag NWs covered by FTO thin films maintained their high-aspect-ratio morphology. As the deposition time of the FTO thin films increased, the electrical and optical properties of the double layers degraded gradually. Therefore, the double layer fabricated with FTO thin films deposited for 1 min exhibited superb sheet resistance (${\sim}14.9{\Omega}/{\Box}$), high optical transmittance (~88.6 %), the best FOM (${\sim}19.9{\times}10^{-3}{\Omega}^{-1}$), and excellent thermal stability at an annealing temperature of $300^{\circ}C$ owing to the good morphology maintenance of the Ag NWs covered by FTO thin films.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.918-921
• /
• 2001

In grinding process, the heat of $1200^{\circ}$~$1500^{\circ}$ on the grinding area between grinding wheel and workpiece is generated. It decreases the surface integrity of workpiece and causes the thermal damages such as the deformed layer, residual stress and grinding burn. Generally coolant is widely used for preventing the heat generation on the grinding area, but it deteriorates the working condition by polluting the atmosphere of workplace and in the end pollutes the environment. The grinding methods using the compressed cold air and mist are the cooling methods to substitute conventional coolant. They can decrease the environmental pollution through not using coolant any more or minimizing it. In this study, the cooling effects of grinding methods using the compressed cold air and mist have been investigated. The grinding system equipped with the water bathe and mist spray nozzle was developed. The energy partition to workpiece through measuring the temperature on the workpiece surface was calculated. The surface integrity of workpiece and thermal damage like the deformed layer were analyzed.

• 한국생산제조학회지
• /
• 제24권1호
• /
• pp.23-30
• /
• 2015

The scanning quality can be influenced by reflective abilities of a surface. Transparency and glossiness of a surface can highly limit the scanning results. Various techniques have been developed to solve problems of reflective and transparent surfaces. As one of the most feasible and convenient solutions, a thin layer of coating with proper specifications is sprayed on surface for eliminating the problems of the surfaces. As the main goal is to keep the object geometry unchanged, then it is important to coat the surface with layers less than one micrometer in thickness. For this purpose, a newly designed atomization-based spray system has been developed and tested in sets of experiments to study its efficiency on scanning results while objects with the surface are in use. This paper presents the spray design process and then studies and compares the 3D scanning results of the surfaces coated with atomization-based and aerosol sprays.

• 한국압력기기공학회 논문집
• /
• 제19권2호
• /
• pp.102-108
• /
• 2023

A Chloride-induced stress corrosion cracking (CISCC) of austenite stainless steel in dry cask storage system (DCSS) can occur with extending service time than originally designed. Cold spray coating (CSC) not only form a very dense microstructure that can protect from corrosive environments, but also can generate compressive stress on the surface. This characteristic of CSC process is very helpful to increase the resistance for CISCC. CSC with several powders, such as 304L, 316L and Ni can be optimized to form very dense coating layer. In addition, the impact energy generated as the CSC powder collides with the surface of base metal at a speed of Mach 2 or more can remove the residual tensile stress of welding area and serve the compress stress. CSC layers include no oxidation and no contamination with under 0.2% porosity, which is enough to protect from the penetration of corrosive chloride. Therefore, the CSC coating layer can be accompanied by a function that can be disconnected from the corrosive environment and an effect of improving the residual stress that causes CISCC, so the canister's CISCC resistance can be increased.