• Journal of Ocean Engineering and Technology
• /
• v.35 no.1
• /
• pp.24-37
• /
• 2021

As one of the development directions of high-performance ships to reduce greenhouse gas emissions, there is research on high-performance propellers. However, in the case of conventional screw propellers, as they have been studied for a long time, there is a limit to improving efficiency only by depending on the conventional design and analysis methods. In this study, we tried to solve the problems using the Coanda effect by spraying a jet on the surface of the hydrofoil. The Coanda hydrofoil consists of a tunnel and jet slit to make jet flow. The computation was performed for each tunnel and slit position, and the efficiency according to the geometry of the hydrofoil was analyzed. In addition, a study on the 3D geometry change was conducted to analyze the performance according to the span direction spraying range and hydrofoil shape. As the height of the slit and the diameter of the tip were lower, when the slit is located in the center of the hydrofoil, the lift force increased and the drag force decreased. The increase rate of lift-to-drag ratio was different according to the shape of the hydrofoil, and the efficiency of the spraying condition of 0.1S-0.5S, which had the least effect on the vortex at the tip of the blade, was high for all 3D hydrofoils. When the geometry of the slit was optimized, and also the shape and spray range of the hydrofoil in 3D was considered, the efficiency of the jet sprayed hydrofoil was increased.

• Journal of ILASS-Korea
• /
• v.25 no.4
• /
• pp.178-187
• /
• 2020

The current emission regulations, US Tier-4 and EU Stage-V, are only able to satisfy the regulations when all currently mass-produced emission reduction technologies such as EGR, DOC, DPF, and SCR are applied. Therefore, in this study, for the application of the Urea-SCR system to non-road diesel engines, the database was established by measuring the NO, NO2 concentration and calculating the NO2/NOx ratio based on the catalyst temperature and exhaust mass flow rate. Also, based on the measured NO2/NOx ratio data, a mathematical model was proposed to predict the NO2/NOx ratio at SCR catalyst, and the suitability of the model was verified through steady-state and transient mode. As a result of comparing the NO2/NOx ratio measured at the DOC outlet under the steady-state condition to two model values separately, the R2 was 0.9811 for the 3D map model and 0.9303 for the mathematical model. And in the case of the NO2/NOx ratio measured at the DPF outlet, the R2 was 0.9797 for the 3D map model and 0.935 for the mathematical model. It was confirmed that the R2 with the model value of the 3D Map of the mathematical model in the transient mode is 0.957, which shows high reliability.

• Journal of ILASS-Korea
• /
• v.25 no.4
• /
• pp.196-203
• /
• 2020

Nowadays, urea SCR technology is considered as the most effective NOx reduction technology of diesel engine. However, low NOx conversion efficiency under low temperature conditions is one of its problems to be solved. This is because injection of UWS (Urea Water Solution) is impossible under such a low temperature condition due to the problem of insufficient of urea decomposition and urea deposits. In several previous studies, it has been reported that appropriate control of the amount of ammonia adsorbed on SCR catalyst can improve the NOx conversion efficiency under low temperature conditions. In this study, we tried to find out how much the NOx conversion efficiency increases with respect to the amount of ammonia adsorbed on the catalyst, and what the temperature conditions that the ammonia slip occurs. This study shows the results of 8 times repeated WHTC test with a diesel engine, in which UWS was injected with NH3/NOx mole ratio of '1'. Through this study, it was found that 13% of the NOx conversion efficiency of WHTC increased while the θ (ammonia adsorption rate) increased from "0%" to "22%". In addition, it is found that in cases of high θ value, the significant improvement of NOx conversion efficiency at low temperatures presented during the beginning period of WHTC and at high temperature and transient conditions presented during last part of WHTC test. The NH3 slip occurring condition was 250℃ of catalyst temperature and 10% of θ, and the amount of NH3 slip increased as the temperature and θ are increased.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.1
• /
• pp.55-59
• /
• 2022

In this paper, we compared the electric field and absorptance of nano particles in nanostructures by amplifying the electric field around the nanoparticles through plasmon resonance and comparing the structure that can increase the absorptance with the nanostructure by using the Finite Different Time Domain (FDTD) simulation. In addition, the width of the nanostructure was adjusted to 240 nm ~ 300 nm, and the light absorptance rate was higher as the gap between the particles was short. In addition, a study was conducted on the formation of nanoparticles and nanostructures on the surface through UV imprint. In order to form particles in the structure, the nano particles were first arranged in the mold used for the fabrication of the structure using spray coating, and then fabricated through UV imprinting. The nanostructure and particles were formed together by scanning electron microscopy.

• Journal of ILASS-Korea
• /
• v.28 no.1
• /
• pp.16-23
• /
• 2023

The objective of this numerical study is to investigate the effect of the shape and material of the blower blade for the electrified speed sprayer on the blowing performance. The shape of the blade was changed to the bonding angle, the number of blades, the width of the blade, and the blade length based on the existing model. In order to obtain the reliability of the numerical model, the analysis of the grid dependence was performed in the numerical analysis. The numerical analysis results were compared and analyzed in terms of the agricultural chemical penetration length characteristics, flow uniformity characteristics, and velocity distribution characteristics. Furthermore, the effect of material change on weight reduction and structural characteristics was also compared and analyzed. As a result of the analysis, it was found that the optimal condition was that the blade angle was 45°, the number of blades was 12, and the width was 115 mm, which was confirmed through a comparison of the inlet mass flow rate. As a result of the equivalent stress lower than the yield strength due to the material change from aluminum to steel compared to the existing steel, structural defects do not appear, and it is judged that the operation time compared to the battery capacity will be improved through the weight reduction of the blade.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.5
• /
• pp.289-298
• /
• 2023

In this study, the effect of drying temperature on characteristics of the trivalent chromate film on electroplated zinc was investigated. An zinc-electroplated iron specimen with a thickness of 5 ㎛ was used for chromate treatment. Chromate treatment was conducted in a solution diluted 10 times from a mixture of Cr(NO₃)₃·9H₂0 360 g/L, Co(NO₃)₂·6H₂O 60 g/L, Na₂SO₄ 60 g/L, NH₄F·HF 25 g/L, and NaOH 20 g/L. The zinc electroplated specimen was treated using the chromate solution with pH 2.0 at 25 ℃ for 60 s. Subsequently, chromate-treated samples were dried in an electric furnace for 2h with temperature varied from 25 to 125 ℃. The corrosion rate increased with the increase in the drying temperature, and the surface morphology of the chromate-treated film was observed using FE-SEM. When the drying temperature changed, the color of the chromate film changed from green to yellow, and the thickness of the film changed from 362 to 241 nm, respectively. Additionally, corrosion resistance was evaluated via a salt spray test.

• The Korean Journal of Pesticide Science
• /
• v.16 no.4
• /
• pp.282-287
• /
• 2012

This study was carried out to clarify the effects of the application of pesticide by different spray nozzle types on pesticide residues. The average droplet size and discharge rate were investigated when the manual compressed sprayer with two head disk type nozzle and the knapsack engine powered sprayer with two head fan shape nozzles were used. The fan type nozzles were classified into three types by the number of orifice in the nozzle. Three type nozzles tested were fan with one orifice, fan with two orifices and fan with three orifices. Fan (trade name : D-3) with 2.4 L/min. of the discharge rate and $76{\mu}m$ of the average droplet size while maintaining constant pressure $1.1{\pm}0.2$ MPa, and fan D-35 with 2.6 L/min. and $90{\mu}m$ while maintaining constant pressure $1.0{\pm}0.2$ MPa were appropriate. The orifice size of D-3 was 0.65 mm length ${\times}$ 0.45 mm width and the orifice size of D-35 was 0.62 mm length ${\times}$ 0.46 mm width. The residue levels of imidacloprid on perilla leaves among four applications by four different nozzles show significantly difference with 5% significance level. The residue levels $3.76{\sim}3.92mg\;kg^{-1}$ by fan or disk type is smaller than $4.52{\sim}4.92mg\;kg^{-1}$ by fan II or fan III. The residue levels of imidacloprid on perilla leaf were different depend on the spray nozzles type.

• Journal of Bio-Environment Control
• /
• v.30 no.4
• /
• pp.263-270
• /
• 2021

This experiment was carried out to determine the effect of CaCl₂ foliar spraying on the inhibition of blossom-end rot (BER) in hot summer paprika (Capsicum annum L. 'Special') cultivation. The effect of CaCl₂ application was examined by the foliar application based on different fruit size, frequency, and spraying time. Also, it was investigated the occurrence and alleviation effect of BER symptom. Foliar application of CaCl₂ (Ca 0.4%) was conducted by treating a fruit and leaf at 4 to 9 nodes above the crown flowers of each plant with 350 mL per week from June 3 to July 1. When the CaCl₂ was sprayed at 7-day intervals for 4 weeks, the Ca content was the lowest in the fruit harvested with BER symptom in 11 to 20 mm of fruit width (FW). Four different regions in both BER symptom and normal fruits showed significant differences of Ca content, the highest was in pedicel, followed by stem-end, middle, and blossom-end. The Ca content increased sharply in normal paprika with 31-40 mm FW, in which Ca content was 78% higher than that of BER. Ca content in the middle and blossom-end of paprika over 21 mm in FW ranged 19.8% to 28.8% in normal fruits and 15.7% to 18.5% in BER, respectively. The incidence of BER increased rapidly by more than 60% in fruits with 31-40 mm FW. While there was no difference in fruit weight among the FW treatment, marketable yield rate was highest in the 21-30 mm FW, and the sugar content was high in the 11-30mm FW. When CaCl₂ was applied three times for 7 days to a paprika having a 21- 30 mm FW, the cell wall-bound (CWB) Ca content was the highest and the rate of BER was lowest with 6.3%. After 10 days of CaCl₂ foliar spray treatment, the CWB Ca content of paprika increased by 2.9 to 3.5 times compared to the control in all treatments. At 7 days after the CaCl₂ foliar spraying once a day at varying spraying time, the leaf burn observed from 9:30 a.m. to 17:00 p.m. and the proline content increased as the spraying time was delayed. Therefore, the CaCl₂ foliar spraying method for reducing of BER occurrence during paprika summer cultivation seems to be appropriate to spray 2-3 times at intervals of 3 days and before 8 a.m. at the time when the FW is 21-30 mm.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.13 no.3
• /
• pp.251-258
• /
• 1984

In order to improve the physical properties on moisture sorption of spray dried red ginseng extract powder (SD-RGEP), the various additives and coating agents were treated, and solubility, sedimentation rate and storage stability of RGEPs treated were investigated. For the moisture-proofing, additive itself was effective in the order casein>dextrin>starch>avicell, but RGEPs treated with additives were effective in the order cord oil+tween-40>starch>casein. But there was no significant difference between RGEP treated less than 1% additive and the moisture-proofing. The coating effect of AEA and CAP on RGEP could not be recognized for the moisture-proofing, whereas that of HPC, corn oil, lecithin and HPC+corn oil was proved to be very effective for the moisture-proofing of RGEP. Also it is required to control the initial moisture content of RGEP. The sedimentation rate of RGEP nontreated was 65.1 seconds, whereas that of RGEPs coated with 1% HPC, 1% corn oil, 1% lecithin and 1% HPC+0.5% corn oil was in the range of 96.2 to 114.3 seconds. The sedimentation rate of RGEPs coated was 1.5 to 1.8 times higher than that of RGEP nontreated, and there was significant difference between solubility and sedimentation rate. Therefore it was no matter for the keeping quality. The sorption rates of RGEPs coated with lecithin $(0.5{\sim}1.0%$), corn oil(0.8%) and cellulose acetate (0.8%) were ranged 54 to 56%, 51 to 55% and 52 to 54%, respectively, and it is found that the moisture-proofing effect of RGEPs coated was about 2 times higher than that of RGEP nontreated. From the result of storage experiment during 3 months under the maltreated condition of $48{\pm}2^{\circ}C$, 75% RH, the moisture sorption of RGEPs coated with corn oil$(0.5{\sim}1.0%$), cellulose acetate(DES, $0.5{\sim}0.8%$) and lecithin (DES, 1.0%) was not at all observed. Therefore it is considered that the circulating period of RGEPs coated with these coating agents could to give more than 3 years.

• The Korean Journal of Pesticide Science
• /
• v.16 no.4
• /
• pp.315-321
• /
• 2012

Fate of acetamiprid and imidacloprid aerially sprayed to control pine wood nematode (Bursaphelenchus xylophilus) were studied in a forest of Haman area. Acetamiprid 20% SL or imidacloprid 20% DC were diluted 100 times and applied two times as rate of 50 L/ha using an aircraft of Bell 206 L helicopter. Average acetamiprid deposits on forest floor ranged from 2 to 4% of standard aerial application rate. Following to the second application, acetamiprid deposits in the pine needle ranged 1.8~8.5 mg/kg and then gradually decreased to 1.2~2.1 mg/kg after 48 days. Deposits on the plant washed off by rainfall and reached to soil surface was ca. 17% of the application rate. All of acetamiprid on the ground resided in the forest floor covering the soil surface, where acetamiprid residues were decreased to a quarter at 48 days after the second application, but they were not detected in soil beneath it. And the only low level of acetamiprid residues, 0.0003 mg/L, was detected in the reservoir nearby the experimental forest on the day of aerial application. The acetamiprid detection was presumably due to spray drift. And average imidacloprid deposits on forest floor ranged from 1 to 3% of standard aerial application rate. Following to the second application, imidacloprid deposits in the pine needle analysed very low concentration of 0.1 mg/kg, but the amount of imidacloprid in wash-off in standard and two-fold treatment were ca. 8% and 4% of the application rate, respectively. Most of imidacloprid on the ground also resided in the forest floor, where imidacloprid residues were decreased to a twentieth at 111 days after the second application, and they were detected below 0.5% of the application rate in sol beneath it. And the low level of imidacloprid, 0.0003~0.0017 mg/L, were detected in the streams in the experimental forest. It was not to the level of contamination concerns.