• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.392-393
• /
• 2006

This paper describes the fabrication of SiCN microstructures for super-high temperature MEMS using photopolymerization of pre-ceramic polymer. In this work. polysilazane liquide as a precursor was deposited on Si wafers by spin coating. microstructured and solidificated by UV lithography. and removed from the substrate. The resulting solid polymer microstructures were cross-linked under HIP process and pyrolyzed to form a ceramic of withstanding over $1400^{\circ}C$. Finally, the fabricated SiCN microstructures were annealed at $1400^{\circ}C$ in a nitrogen atmosphere. Mechanical characteristics of the SiCN microstructure with different fabrication process conditions were evaluated. The elastic modules. hardness and tensile strength of the SiC microstructure implemented under optimum process conditions are 94.5 GPa, 10.5 GPa and 11.7 N/min, respectively. Consequently, the SiCN microstructure proposed in this work is very suitable for super-high temperature MEMS application due to very simple fabrication process and the potential possiblity of sophisticated multlayer or 3D microstructures as well as its good mechanical properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.61-62
• /
• 2006

In this paper, it was demonstrated that organic thin- film transistors (OTFTs) were fabricated with the organic adhesion layer between an organic semiconductor and a gate insulator by vapor deposition polymerization (VDP) processing. In order to form polymeric film as an adhesion layer, VDP process was also introduced instead of spin-coating process, where polymeric film was co-deposited by high-vacuum thermal evaporation from 6FDA and ODA followed by curing. The saturated slop in the saturation region and the subthreshold nonlinearity in the triode region were c1early observed in the electrical output characteristics in our organic thin film transistors using the staggered-inverted top-contact structure. Field effect mobility, threshold voltage, and on-off current ratio in 15-nm-thick organic adhesion layer were about $0.5\;cm^2/Vs$, -1 V, and $10^6$, respectively. We also demonstrated that threshold voltage depends strongly on the delay time when a gate voltage has been applied to bias stress.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.114-115
• /
• 2007

In this paper, it was demonstrated that organic thin-film transistors (OTFTs) were fabricated with the organic passivation layer by vapor deposition polymerization (VDP) processing, In order to form polymeric film as an passivation layer, VDP process was also introduced instead of spin-coating process, where polymeric film was co-deposited by high-vacuum thermal evaporation from 6FDA and ODA followed by curing, Field effect mobility, threshold voltage, and on-off current ratio with 450-nm-thick organic passivation layer were about $0.21\;cm^2/Vs$, IV, and $1\;{\times}\;10^5$, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.145-145
• /
• 2000

M-CeO2 (M : noble metal) catalysts have been widely studied as three-way catalysts and methanol synthesis catalysts. Ceria is thought to play a number of roles in these catalysts. The Ce(IV)/Ce(III) redox pair may store/release gases under oxidizing/reducing conditions, extending the operational window. Additionally, metal-ceria interactions lead to several effects, including the dispersion of the active components and promoting the activation of molecules such as CO or NO. Pd is a promising component to current TWC formulations and behaves particularly well when compared with Pt and Rh-based catalysts for low-temperature oxidation of Co and hydrocarbon. However the effect of Pd-ceria interactions on the physicochemical properties of Pd and the redox properties of Ce is not elucidated yet. In order to know exactly about the metal-ceria interactions, the model study are expecting to give a better environment, resulting in the wide use of the surface science tools. The substrate was Si(100) wafer, on which Ta metal was sputtered as a thickness of 100nm. The CeO2 thin film of 30nm was deposited by using the magnetron sputtering. Spin coating and magnetron sputtering methods were used to make the Pd thin film layer. The prepared sample was investigated by in-situ XPS, AES, SEM and AFM analysis.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.4
• /
• pp.323-327
• /
• 1999

A water-soluble conducting polymer (CPP400 Paste) containing a derivative of polythiophene with several dopant was investigated as an anode material for organic electroluminescent devices. The device of ITO/CPP 400 Paste/TPD/$Alq_3$/Li:Al was fabricated, where CPP 400 Paste films were prepared by spin coating and TPD and $Alq_3$, films were prepared by vacuum evaporation. It was found that the turn-on voltage, current density, and luminance of the devices were dependent upon the thickness of CPP 400 Paste film in the Electroluminescent and current-voltage characteristics of the devices. This phenomena were explained by the energy level diagram of the device with the energy levels of the CPP400 Paste obtained by cyclic voltammetric method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.809-812
• /
• 2004

(Pb,Sr)TiO3 (PST) thin films were fabricated by using the alkoxide-based sol-gel method. The PST stock solution was made and then spin-coated onto a PUTi/SiO2/Si substrate. The coating and drying procedures were repeated several times, and the PST thin films were sintered at 450-650 C for 1 h. All PST thin films showed dense and homogeneous structures without the presence of any rosette structure. The thicknesses of the PST thin films were approximately 200 nm. The dielectric constant and the dielectric loss of the PST thin films sintered at 550 C were about 404 and 0.0023, respectively. The leakage current density of the PST thin film sintered at 550 C was 3.13 x 10-8 A/cm2 at 1 V.

• Korean Journal of Chemical Engineering
• /
• v.36 no.6
• /
• pp.975-980
• /
• 2019

Infrared (IR) spectroscopy is a powerful technique for observing organic molecules, as it combines sensitive vibrational excitations with a non-destructive probe. However, gaseous volatile compounds in the air are challenging to detect, as they are not easy to immobilize in a sensing device and give enough signal by themselves. In this study, we fabricated a thin nanocrystalline metal-organic framework (nMOF) film on a surface plasmon resonance (SPR) substrate to enhance the IR vibration signal of the gaseous volatile compounds captured within the nMOF pores. Specifically, we synthesized nanocrystalline HKUST-1 (nHKUST-1) particles of ca. 80 nm diameter and used a colloidal dispersion of these particles to fabricate nHKUST-1 films by a spin-coating process. After finding that benzene was readily adsorbed onto nHKUST-1, an nHKUST-1 film deposited on a plasmonic Au substrate was successfully applied to the IR detection of gaseous benzene in air using surface-enhanced IR spectroscopy.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.6
• /
• pp.324-330
• /
• 2021

As energy harvesting technology becomes important in relation to environmental issues, piezoelectric materials that convert mechanical energy into electrical energy are attracting attention. However, PZT, a representative material for piezoelectricity, is becoming difficult to use due to the problem that its components can cause environmental pollution. For this reason, recent research suggests a triboelectric nanogenerator (TENG) that generates energy through the combined effect of triboelectricity and electric induction for alternative piezoelectric devices. In TENG, electrical power is determined by the dielectric constant, thickness, and grain generation of the charged material. Therefore, in this study, a Rutile phase TiO₂ thin film with high dielectric constant was formed using the spin-coating process and the effect of annealing was investigated. For electrical analysis, a TENG device was fabricated using PTFE as a material with an opposite charge, and electrical output according to film thickness and grain formation was comparatively analyzed.

• Journal of the Microelectronics and Packaging Society
• /
• v.25 no.4
• /
• pp.119-122
• /
• 2018

Various ZnO/Ag/ZnO multilayers were fabricated and their optical properties were investigated. Top and bottom ZnO layers were formed by sol-gel method and mid-metal layers were deposited by spin coating. To find suitable deposition condition of Ag, we measure thickness and sheet resistance of Ag monolayer. After the optimization of Ag monolayer, we fabricate ZnO/Ag/ZnO multilayers. Transmittance of ZnO/Ag/ZnO multilayers increased to 63%. In near IR region, transmittance of ZnO/Ag/ZnO multilayers decreased to 35% when the concentration of Ag solution was 2.5wt%.

• Korean Journal of Materials Research
• /
• v.29 no.5
• /
• pp.297-303
• /
• 2019

A triple-layered $PMMA/Ni_{64}Zr_{36}/PDMS$ hydrogen gas sensor using hydrogen permeable alloy and flexible polymer layers is fabricated through spin coating and DC-magnetron sputtering. PDMS(polydimethylsiloxane) is used as a flexible substrate and PMMA(polymethylmethacrylate) thin film is deposited onto the $Ni_{64}Zr_{36}$ alloy layer to give a high hydrogen-selectivity to the sensor. The measured hydrogen sensing ability and response time of the fabricated sensor at high hydrogen concentration of 99.9 % show a 20 % change in electrical resistance, which is superior to conventional Pd-based hydrogen sensors, which are difficult to use in high hydrogen concentration environments. At a hydrogen concentration of 5 %, the resistance of electricity is about 1.4 %, which is an electrical resistance similar to that of the $Pd_{77}Ag_{23}$ sensor. Despite using low cost $Ni_{64}Zr_{36}$ alloy as the main sensing element, performance similar to that of existing Pd sensors is obtained in a highly concentrated hydrogen atmosphere. By improving the sensitivity of the hydrogen detection through optimization including of the thickness of each layer and the composition of Ni-Zr alloy thin film, the proposed Ni-Zr-based hydrogen sensor can replace Pd-based hydrogen sensors.