• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권4호
• /
• pp.358-365
• /
• 2005

In induction machine drive without a speed sensor, the estimation of the motor flux and speed often becomes deteriorated at low speeds with low back EMF. Our analysis shows that, in addition to the state resistance variation, the estimated value of field orientation angle is often corrupted by accumulative errors from the integration of voltage variables at motor terminals that have low signal/noise ratio at low frequencies. A repetitive loop path of integration in the feedback can amplify this type of error, thus speeding up the degradation process. The control system runs into information starvation due to the loss of correct field orientation. The machine's spiral vectors are controlled only in a reduced dimension in this situation. A novel control scheme is developed to improve the control performance of motor's current, torque and speed at low frequencies. The scheme gains a full-dimensional vector control and is less sensitive to the combined effect of the error sources at the low frequencies. Experimental tests demonstrate promising performances are achievable even below 0.5 Hz.

• 한국대기환경학회지
• /
• 제14권6호
• /
• pp.607-620
• /
• 1998

The influence of transportation on air quality has been elevating in urban area. Air pollutants from automobiles cause primary and secondary air pollution, and need to be tightly controlled. In this study, the effect of automobile air pollutants on highway vicinity area was evaluated by the comparison of field measurement. and target was for modeling using CALINE3, NO2 was the target for this work. It was found that the concentration predicted by CALINE3 is overestimated at low wind speed and input data of wind speed requires correction. Based on the measured data, the wind speed was modified by effective wind speed equation [Ue=U+0.24·EXP(-pxU)], and there after the accuracy of CALINE3 calculation was improved neighborhood area of highway. It was also observed that weather conditions and traffic volume affect the concentration of air pollution. Finally, the NO2 effect of automobile air pollutants on the vicinity area of highway proved to be up to 400∼600m from the highway.

• 대한교통학회지
• /
• 제26권3호
• /
• pp.85-95
• /
• 2008

고속도로 교통사고 발생의 주요 원인인 과속을 줄이기 위하여 경찰청에서는 많은 예산을 들여 과속단속카메라를 설치 운영하고 있다. 지점식 과속단속카메라의 경우 GPS 탑재장치에 의해 위치가 노출되어 과속단속 실적이 떨어지며, 과속단속카메라가 설치되지 않은 차로나 구간에서 캥거루 주행 등 회피거동에 의해 과속억제 효과 또한 감소하고 있다. 운전자의 회피거동으로 인하여 긴 내리막 구간, 터널, 교량 등에서 과속예방효과나 교통사고 감소효과는 제한적일 수밖에 없다. 따라서 중요 시설이나 위험구간에서 차량들의 속도를 일정하게 유지시켜 교통사고 예방효과를 높이기 위한 대안으로 구간과속단속의 필요성이 높아지고 있다. 따라서, 본 연구에서는 우리나라 고속도로에 최초로 도입된 구간과속단속시스템의 효과평가를 위하여 시스템 적용 전 후 교통류특성과 관련된 자료를 수집하여 비교.분석하였고, 그 결과, 시스템 설치 후 속도저감 효과 및 해당 구간의 교통류 안정적 흐름을 보이는 것으로 나타나 구간과속단속 운영구간에 있어서 교통안전성 제고와 교통사고 감소효과가 있는 것으로 파악되었다.

• 한국철도학회논문집
• /
• 제12권6호
• /
• pp.983-988
• /
• 2009

기존선 속도향상 시에 주행안전성을 고려한 기존선 구간별 최대 운행가능속도에 대한 실용적인 기준 을 제시하여 기존선의 곡선부 및 완화곡선부 통과 시 속도를 향상시켜야 한다. 본 연구에서는 탈선의 위험도가 높은 곡선부 통과하는 열차의 고속향상을 도모하기 위하여 실제 선로조건인 남성현-청도 상 하행 구간에서의 곡선부 구간별 통과시 주행안전성에 미치는 영향을 살펴보았다. 곡선반경별 주행속도를 실제 선로 조건에서의 기존 속도 대비 5-20% 향상시켜 주행안전성 해석을 수행하였다. 주행안전성 해석 결과, 기존 주행속도 대비 약 15% 이하의 속도조건에서는 탈선 계수와 윤중감소율이 허용기준 이내로 나타나 남성현-청도 상 하행 전 구간 내에서 속도 향상의 가능성을 확인할 수 있었다.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1124-1130
• /
• 2015

Moisture and high temperature are the most important factors that lead to the ageing of oil-paper insulation, but the research about space charge characteristics of oil-paper insulation does not take the combined effect of ambient temperature, moisture and thermal ageing into account. The pulsed electroacoustic (PEA) method was used to investigate the influence of moisture and temperature on space charge characteristics of oil paper at different ageing stages. The results showed that moisture could speed up formation of space charge in oil paper when water concentration was low, but the formation was restrained if the water concentration was high. At the beginning of thermal ageing, heterogeneous charge accumulation had predominance, but it gradually changed to homogeneous charge injection with ageing. It was believed that moisture concentration could speed up ageing and enhance charge accumulation on one hand, and accelerate or slow down the establishment speed of space charge on the other hand, therefore, charge accumulation type changed with ageing. The more seriously the oil-paper insulation was thermally aged, the deeper the trap energy level was, hence more space charge was trapped, which could be speeded up by increasing the ageing temperature, but the effect of ambient temperature did not fit the Arrhenius law.

• Fibers and Polymers
• /
• 제6권1호
• /
• pp.19-27
• /
• 2005

High-speed melt spinning of syndiotactic polystyrene was carried out using high and low molecular weight poly­mers, HM s-PS and LM s-PS, at the throughput rates of 3 and 6 g/min. The effect of take-up velocity on the structure and properties of as-spun fibers was investigated. Wide angle X-ray diffraction (WAXD) patterns of the as-spun fibers revealed that the orientation-induced crystallization started to occur at the take-up velocities of 2-3 km/min. The crystal modification was a-form. Birefringence of as-spun fibers showed negative value, and the absolute value of birefringence increased with an increase in the take-up velocity. The cold crystallization temperature analyzed through the differential scanning calorimetry (OSC) decreased with an increase in the take-up velocity in the low speed region, whereas as the melting temperature increased after the on-set of orientation-induced crystallization. It was found that the fiber structure development proceeded from lower take-up velocities when the spinning conditions of higher molecular weight and lower throughput rate were adopted. The highest tensile modulus of 6.5 GPa was obtained for the fibers prepared at the spinning conditions of LM s-PS, 6 g/min and 5 km/min, whereas the highest tensile strength of 160 MPa was obtained for the HM s-PS fibers at the take-up velocity of 2 km/min. Elongation at break of as-spun fibers showed an abrupt increase, which was regarded as the brittle-duc­tile transition, in the low speed region, and subsequently decreased with an increase in the take-up velocity. There was a uni­versal relation between the thermal and mechanical properties of as-spun fibers and the birefringence of as-spun fibers when the fibers were still amorphous. The orientation-induced crystallization was found to start when the birefringence reached -0.02. After the starting of the orientation-induced crystallization, thermal and mechanical properties of as-spun fibers with similar level of birefringence varied significantly depending on the processing conditions.

• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.635-641
• /
• 2011

The effect of high shear speed on shear force, shear energy and fracture surface was investigated for the solder joint of a $Sn-_{3.0}Ag-_{0.5}Cu$ ball. For both ENIG and OSP pads, the shear force increased with an increase in shearing speed to 0.3 m/s. However, for an ENEPIG pad, the shear force increased with an increase in shear speed to 0.6 m/s and kept almost constant afterward. The shear energy decreased with an increase in shearing speed for ENIG and OSP pads. For the ENEPIG pad, however, the shear energy almost remained constant in a shearing speed range 0.3-3.0 m/s. The fracture mode analysis revealed that the amount of brittle fracture for the ENIG and the OSP pads increased with shearing speed, and a complete brittle fracture appeared at 1.0 m/s for ENIG and 2.0 m/s for OSP. However, the ENEPIG pad showed only a ductile fracture until 0.25 m/s, and a full brittle fracture didn't occur up to 3.0 m/s. The fracture mode matched well with the shear energy. The results from the high speed shear test of SAC305 were similar to those of SAC105.

• 한국태양에너지학회 논문집
• /
• 제33권3호
• /
• pp.1-8
• /
• 2013

In order to identify positive or negative effect of seawall on wind turbine, a wind tunnel experiment has been conducted with a 1/100 scaled-down model of Goonsan wind farm which is located in West coast along seawall. Wind speedup due to the slope of seawall contributed to about 3% increment of area-averaged wind speed on rotor-plane of a wind turbine which is anticipated to augment wind power generation. From the turbulence measurement and flow visualization, it was confirmed that there would be no negative effect due to flow separation because its influence is confined below wind turbine blades' sweeping height.

• 한국정밀공학회지
• /
• 제18권5호
• /
• pp.130-136
• /
• 2001

Generally, a metal slitting saw is plain milling cutter with thickness less than 3/16 inch. This is used for cutting a workpiece that high dimensional accuracy and surface finish is necessary. A small thin milling cutter like a metal slitting saw is useful for machining a narrow groove. In this case, built up edge(BUE) is severe at each tooth and affects the surface integrity of the machined surface and tool wear. It is well known that tool geometry and cutting conditions are decisive factors to remove BUE. In this paper, we optimized the geometry of the milling cutter and selected cutting conditions to remove BUE by the experimental investigation. The experiment was planned with Taguchi method based on the orthogonal array of design factors such as coating, rake angle, number of tooth, cutting speed, feed rate. Response table was obtained from the number of built-up edge generated at tooth. The optimized tool geometry and cutting conditions could be determined through response table. In addition, the relative effect of factors was identified bh the analysis of variance (ANOVA). Finally, coating and cutting speed turned out important factors for BUE.

• 한국전기전자재료학회논문지
• /
• 제13권5호
• /
• pp.371-375
• /
• 2000

In this paper a new conductivity modulated power transistor called the Lateral Insulated Gated Bipolar Transistor which included n+ ring and p-channel gate is presented. A new lateral IGBT structure is proposed to suppress latch-up and to improve turn off time by imploying n+ ring and p-channel gate and verified by MEDICI. The simulated I-V characteristics at $V_{G}$=15V show that the latch up occurs at $V_{A}$=18V and 6.9$\times$10$^{-5}$ A/${\mu}{\textrm}{m}$ for the proposed LIGBT while the conventional LIGBT latches at $V_{A}$=1.3V and 1.96${\mu}{\textrm}{m}$10$^{-5A}$${\mu}{\textrm}{m}$. It is shown that turn off characteristic of new LIGBT is 8 times than that of conventional LIGBT. And noble LIGBT is not n+ buffer layer because that It includes p channel gate and n+ ring. Therefore Mask for the buffer layer isn’t needed. The concentration of n+ ring is and the numbers of n+ ring and p channel gate are three for the optimal design.n.n.n.n.