It has been applied several ways in order to prevent traffic accidents and speed management on the road which is one of very important factors to prevent accidents. In this study, it is analyzed whether the facility such as the flashing and crosswalk, speed cameras and intermittent warning signs affect on a driving deceleration or not. It has been shown that the flashing and crosswalk and speed cameras except intermittent warning signs play a role of reducing the driving speed. The result showed that these traffic safety facilities help to improve the average speed as well as velocity distribution which was derived by the speed deviation even if there were the difference between facilities. Speed limit display does not affect the deceleration of the driver. Therefore, it was founded in this research that there were the driving speed reduction effect due to the facilities on the road. In order to control the driving speed on the road, it is necessary to install facilities with appropriate location and spacing on the road. In addition, place that turns out suppressed speeding through speed management also are required adequate facilities such as speed cameras.
This paper describes the calculation and application of the speed profile for the train speed control when the train is operated by ATO(Automatic Train Operation). We propose a speed profile calculation method considering the speed limitation and the jerk limitation, in order to maintain the quality of the train automatic operation. In previous works, ATO calculates a desired speed profile along the time, and controls the train to follow the profile. In this case, it may be hard to follow the restrictive speed along the location or to stop the train with a low location error, because of the difference between the desired location at each time and the real location of the train due to the control error. In the proposed method in this paper, we calculate a desired speed profile along the time considering the speed and jerk limitation first, and derive a speed profile along the location using it. If the restrictive speed profile is changed or the train speed strayed from the speed profile, ATO system calculates new speed profile and applies it immediately. Because ATO system controls the train speed based on the train location, the accuracy of the train location control can be improved. A simulation system for the test of the automatic train operation using this method is designed.
The Transactions of the Korean Institute of Power Electronics
/
v.27
no.5
/
pp.438-445
/
2022
Blade efficiency decreases when the rotor speed is kept constant even though the wind speed is higher than the rated value. Therefore, a speed controller is used to regulate the rotor speed in the high-wind-speed region. In stall-blade wind turbine, the role of the speed controller is important because precise aerodynamic regulation is unavailable. In this study, an effective parameter design method of a PI speed controller is proposed to limit the speed overshoot of a type 4 wind turbine with stall blades even though wind gust occurs. The proposed method considers the efficiency characteristics of the stall blade and the mechanical inertia of the wind turbine rotor. It determines the bandwidth of the speed controller to comply with the speed limit during generator speed overshoot for the worst case of wind gust. The proposed method is verified through intensive simulations with a MATLAB/SIMULINK model and experimental results obtained using a 3 kW MG set of wind turbine simulator.
Journal of Advanced Marine Engineering and Technology
/
v.28
no.4
/
pp.641-647
/
2004
By most sensorless speed control schemes for induction motor. the control performances in high speed range are good, but it is difficult to obtain satisfactory results in low speed region. This paper proposes a new method controlling the low and the high speed regions separately to attain the stable operation in the overall range. The current error compensation method, in which the controlled stator voltage is applied to the induction motor so that the error between stator currents of the numerical model and the actual motor can be forced to decay to zero as time proceeds. is used in the low speed region In the high speed region. the method with adaptive observer is utilized. This control strategy contains an adaptive state observer for flux estimation. The rotor speed can be calculated from the rotor flux and the motor currents. The experimental results indicate good speed and load responses from the very low speed range to the high, and also show accurate speed changing performance between the low and the high speed range.
This paper presents a novel reference variable speed control scheme of a BLDC motor for the high-speed blender machine according to the current limit. Because of a pulsating load variation of a high-speed blender machine, the actual speed is pulsated by the current limit in the high-speed region. The proposed control scheme uses a variable reference speed to reduce the speed variation from the current limit in the constant power region. The pulsated load is occurred at the material crushing, then the pulsated load is reduced after grinding. The reference speed is smoothly reduced at the pulsated load variation, then the enough torque can make a constant speed during crushing. When the pulsating load is reduced, the reference speed is automatically increased to the original speed value. The proposed control scheme is verified by experimental result by practical blender machine.
International Journal of Advanced Culture Technology
/
v.10
no.3
/
pp.332-338
/
2022
The article presents a concept of designing a Multiplexer circuit which acts as a "Selector" and that becomes capable to select different speed created at different TTL Gate configurations; Standard TTL(Normal Speed), High Speed TTL(High Speed), Schottky TTL(Super High Speed) and further connect the selected Gate speed to the CAR shape created using C-Programming at Computer Graphics and finally CAR shape display at different speed to the color TV. The Multiplexer supporting efficient and more reliable selection criteria using "Logical based selection criteria" and further the output from multiplexer is provided to CAR shape created using c-programming and finally CAR shape is display to color TV system. Basic purposes and assumptions regarding the design and development of this system as well as a description of its operation have been presented.
Some GM (General Motors) vehicles are using a GMLAN (General Motors Local Area Network) communication protocol for control and diagnostics. The airbag control module uses vehicle speed information from the GMLAN to record the vehicle speed as pre-crash information. In order to use the vehicle speed information for crash reconstruction purposes, it helps to be able to understand the accuracy of the data. The actual vehicle speed is not expected to be the same as the GMLAN indicated speed in some situations like a spin or if there is hard braking. This paper compares the actual vehicle speed and vehicle speed information during specific vehicle maneuvers. Actual vehicle speed is calculated from a GPS sensor, while GMLAN vehicle speed is calculated from transmission output sensor by the Engine control module (ECM). Vehicle maneuvers defined as Mode #1, Mode #2, Mode #3. The Mode #1 maneuver simulates wheel lock-up and skidding f by hard-braking at a specific speed. The Mode #2 maneuver simulates a 90degree turn using a J-turn maneuver at a specific speed. The Mode#3 maneuver simulates a 180 degree turn using a spin type of maneuver at a specific speed. The study then compares the GMLAN speed and GPS speed to see what speed difference exists between them. The results of this paper are applicable to GM vehicles only. This paper catalogs the performance and limitations of two vehicles as useful reference for crash reconstructions where there is a need to understand the speed indicated in the pre-crash section of the SDM data.
Transactions of the Korean Society of Machine Tool Engineers
/
v.14
no.2
/
pp.21-26
/
2005
From on the machining center cutting work of 5534, the characteristics such as spindle speed and feed speed fir the third point height, average spacing of roughness peaks, bearing ratio, center line average, ten point height. experiments is roughness for sampling length determine to measuring length of cutting feed speed 200, 400, 600, 800mm/min and spindle speed 800, 1000, 1200, 1400rpm. Third point height is spindle speed with most suitable cutting condition 1000rpm. Third point height is feed speed with most suitable cutting condition 400mm/min. Average spacing of roughness peaks are spindle speed with most suitable cutting condition feed speed increased to average spacing of roughness Peaks are increased. Spindle speed increased to average spacing of roughness peaks are decreased. Bearing ratio is spindle speed with feed speed increased to bearing ratio decreased. Center line average is spindle speed with most suitable cutting condition at 1200rpm feed speed with most suitable cutting condition at 200mm/min to cutting foe roughness suddenly decreased. Ten point height is spindle speed with most suitable cutting condition 1200rpm at ten point height cutting face roughness to decreased and feed speed with most suitable cutting condition 800mm/min at ten point height cutting face roughness to decreased.
Proceedings of the Korean Institute of Intelligent Systems Conference
/
2004.04a
/
pp.153-156
/
2004
This Paper deals with speed control of DC servo motor using a Fuzzy-Sliding observer. Speed sensor detect a speed of rotor continuously. But It have a limit as a driving speed to detect speed precisely. So it is problem to improve the performance of the driving system To solve the problem, it is studied to detect a speed of DC motor without sensor In particular, study on the method to estimate the speed using the observer is performed a lot. In this parer, the gain of the observer is properly set up using the fuzzy control and sliding observer that have a superior transient characteristic and is easy to implement compared the exist ing method is designed. It estimate the derivative of the armature current directly using the armature current measured in the DC motor. It estimate the speed of the rotor using the differentiation. It is Proposed speed sensor less control method using the estimated speed. Optimal gain of Luenberger observer is set up using the fuzzy control and adapted speed control of DC servo motor. It is proved excellence and feasibility of the presented observer from the comparison tested a case with a speed sensor and a case without a speed sensor which used a highly efficient drive and 200W DC servo motor start ing system.
In the speed control system of motors using the low resolution rotary encoder, the period of encoder pulse becomes longer than the sampling time for speed control in the range of very low speed. Therefore, it is difficult to obtain accurate speed information. In this paper, the speed estimating method at the very low speed region using reduced order torque observer, which has been widely used, is examined. The results of simulation show that the characteristics of the speed control at the very low speed region is improved by using the reduced order torque observer.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.