• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 추계학술발표대회 개요집
• /
• pp.74-77
• /
• 1999

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1999년도 특별강연 및 춘계학술발표대회 개요집
• /
• pp.150-151
• /
• 1999

• Journal of Welding and Joining
• /
• 제20권4호
• /
• pp.525-534
• /
• 2002

During laser spot welding of the braun tube electron gun, phenomena such as serious spattering and oxidative reaction, etc. were occurred. The spatter occurred from weld pool affects the braun tube, namely it blocks up a very small hole on the shadow mask and causes short circuit between two roles of the electron gun. We guessed that high power density and oxidative reaction are main sources of these problems. So, we studied to prevent and to reduce spatter occurring in spot welding of the braun tube electron gun using pulsed Nd:YAG laser. The characteristics of laser output power was estimated, and the loss of laser energy by optical parameter and spatter was measured by powermeter. The effects of welding parameters, laser defocused distance and incident angle, were investigated on the shape and penetration depth of the laser welded bead in flare and flange joints. From these results, the laser peak power was a major factor to control penetration depth and to occur spatter. It was found that the losses of laser energy by optic parameter and sticked spatter affect seriously laser weldability of thin sheets. The deepest penetration depth is gotten on focal position, and a "bead transition" occurred with a slight displacement of focal position relative to the workpiece surface and the absorption rate of the laser energy is affected by the shape factor of the workpiece. When we changed the incident angle of laser beam, the penetration depth was decreased a little with increasing of the incident angle, and the bead width was increased. The spattering was prevented by considering laser beam energy and incident angle.ent angle.

• Journal of Welding and Joining
• /
• 제16권3호
• /
• pp.95-101
• /
• 1998

Waveforms of $CO_2$ gas shielded arc welding in short circuit transfer mode was studied with the waveform analysis program, which can calculate various waveform factors such as number of short circuit event, mean and standard deviation of short circuit time and arc time. The calculated values of these factors were correlated independently or in combination with the spatter generation rate to figure out the most reliable index for evaluating spatter generation and further for arc stability. As a result this study, it was confirmed that the spatter generation tends to decrease with the increase of short circuit frequency. Further to this, it was also found that as the short circuit frequency increases the short circuit event becomes more uniform resulting in the decrease of standard deviations ($\sigma$values) of short circuit time and arc time. This result demonstrated that these factors are strongly correlated with each other and thus any one of these factors can be used for the evaluation index. In the discussion, however, short circuit frequency was proposed for the most practical index in evaluating the arc stability of short circuit transfer mode since it is the one which could be monitored in-process condition without any complex caculation process.

• 전력전자학회논문지
• /
• 제4권2호
• /
• pp.128-137
• /
• 1999

최근 전력전자기술 및 인버터 회로의 다양한 제어기법의 발달에 따라서 용접기 분야에서의 용접성능 향상에 관한 다양한 연구가 진행되고 있으며 특히{{{{ { CO}_{2 } }} 아크 용접기의 경우 용접성능을 좌우하는 스패터 발생을 최소화 하는 기법이 활발하게 연구되고 있다. 그러나 현재까지는 용접기의 출력전압을 정전압으로 제어하는 방식을 사용함에 따라 용접기의 금속이행과정을 임의로 제어하는 것이 불가능하였고, 특히 스패터가 다량으로 발생하는 저전류영역의 금속이행과정인 단락이행에서의 스패터 저감을 기대하기가 어려웠다. 따라서 본 논문에서는 마이크로프로세서를 이용한 인버터 출력전류의 파형제어기법을 사용하여 인버터 아크 용접기의 출력전류를 순시적으로 제어함에 의하여 스패터 저감, 단락주기의 안정화 및 순간단락현상 감소의 측면에서 용접성능을 개선위한 연구를 수행하였고 이상의 연구에 대한 결과를 제시하였고, 또한 인버터 아크 용접기의 AC/DC 전력변환장치로 SMR(Switched Mode Rectifier)를 사용하여 시스템을 단위역율로 운전하였으며 입력전류의 저차 고조파 억제효과를 얻을 수 있었다.

• Journal of Welding and Joining
• /
• 제14권5호
• /
• pp.145-150
• /
• 1996

The variation of spatter generation in gas metal arc welding with welding conditions and wire compositions was investigated and interpreted in terms of arc stability. The transition range from a short circuit mode to a spray mode in the mixed gas welding showed an unstable arc and generated the largest amount of spatters. Titanium reduced spatters only in the globular mode of $CO_2$welding and silicon and manganese showed the same effect The effect of silicon and manganese, however, was no longer seen when titanium was added simultaneously to the wire. It is believed that deoxidizers easily form oxides on the anode and make the arc stable even in DCRP welding. The wires with deoxidizers also showed low short circuit frequency, resulting in the increase of large size spatters.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.171-173
• /
• 2004

Electromagnetic force is one of the most important factor that effect on metal transfer mode, short-circuit rate, spatter generation rate and mechanical properties of weld metal etc. Also, shielding gas and welding current have influence on metal transfer mode in GMAW. In this paper, different ways for external electromagnetic forces are applied by attaching cylindrically rounded conducting wire solenoid on touch tip holding. With the applied electromagnetic field, the arc transfer mode changes from normal mode to rotating mode and spatter generation decreased in electromagnetic fields(N-pole). In MIG welding, the influences of electromagnetic force on the spatter generation showed different tendency as in the $CO_2$ welding. It is possible reasons were discussed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.581-586
• /
• 2000

Gas metal arc welding(GMAW) uses a continuously fed electrode as a filler metal. The arc is shielded from atmospheric contamination by an inert gas active or inert/active gas mixture delivered through the welding gun and cable assembly. The recent research topics on $CO_2$ are welding machines are focused mainly on the reduction method of generated spatter by using new type consumable electrode metal or inverter control method. The various current waveform control methods have been researched for welding performance improvement. Until now current waveform control methods reduce to spatter occurred by instantaneous short circuiting,. but these methods is drawback that no reduce spatter occurred by arc reignition. In this paper the previous arc reignition current control method for welding performance improvement of inverter arc welding machine is studied and compared the various current control methods with the previous arc reignition current control method.

• Journal of Welding and Joining
• /
• 제19권5호
• /
• pp.486-491
• /
• 2001

The effect of S content in welding wires on spattering characteristics and droplet transfer phenomena was studied. In MAG welding using 80%Ar-$20%CO_2$ shielding gas, spattering characteristics and droplet transfer phenomena were varied with S content of wire. Sulfur addition in wire reduced surface tension of droplet and weld pool, and made arc more stable in MAG welding. With increasing S content, the spattering ratio and the ratio of large size spatter ($d{\geq}1.0mm$) were reduced in short circuit transfer mode. In spray transfer mode, spattering ratio, however was increased when sulfur was added more than 0.020wt.% because surface tension of droplets and weld pool was reduced too much even though arc stability was improved.

• International Journal of Korean Welding Society
• /
• 제1권1호
• /
• pp.7-12
• /
• 2001

Real time monitoring has become critical as the use of laser welding increases. Plasma and spatter are measured and used as the signal for estimating weld quality. The estimating algorithm was made using the fuzzy pattern recognition with the area of data that is beyond the tolerance boundary. Also, an algorithm that detects the spatter and the localized defect was created in order to kd the partially produced pit and the sudden loss of weld penetration. These algorithms were used in quality monitoring of the $CO_2$ laser tailored blank weld. Statistical program that can display the laser weld quality result and the signal transition was made for the first stage of the remote control system.