• 한국ITS학회 논문지
• /
• 제21권5호
• /
• pp.149-161
• /
• 2022

제한속도는 주행속도에 영향을 주기 때문에 교통흐름은 물론 교통사고와도 밀접한 관계에 있다. 기존 제한속도 산정 방법은 공학적 판단요소로 차로수, 교차로 간격, 진출입로 수, 횡단보도 수, 85백분위 속도, 토지이용 형태, 도로기하 특성 등 다양한 요소들을 고려하지만 대부분이 교통시설에 해당되고 교통량을 고려한 교통영향분석이 이루어지지 않고 있어 공학적 분석이 미흡하다고 할 수 있다. 또한 지점속도인 85%속도만으로는 도로 전체의 교통류 특성을 잘 반영해주지 못한다. 따라서 본 논문에서는 교차로 간격과 교통량 조건에서 제한속도 변화가 순행속도와 통행속도의 크기와 그 차이에 미치는 영향을 상세하게 분석하였다. 그리고 그 결과를 활용하여 제한속도 변경 전과 동일한 서비스수준을 유지토록 하여 속도개선효과를 높이고 순행속도와 통행속도의 차이를 줄이는 제한속도 산정방안을 제안하였다. 그리고 교통량 변화에 따른 가변적 제한속도 운영방안도 제시하였다. 본 방안은 속도개선효과를 확보하면서 교통사고 심각도에 영향을 주는 속도 차이를 줄이고 교통량 변화에 따른 주행속도 변화를 반영한 제한속도 운영으로 운전자들의 제한속도 준수율을 높여 안전측면에서도 효과가 기대된다.

• 산업기술연구
• /
• 제25권A호
• /
• pp.39-47
• /
• 2005

Air void systems in hardened concrete has an important influence on concrete durability such as freeze-thaw resistance, water permeability, surface scaling resistance. Linear traverse method and point count method described at ASTM are the routine analysis of the air void system that have been widely used to estimate the spacing factor in hardened concrete. Recently, many concretes often have a spacing factor higher than the generally accepted $200-250{\mu}m$ limit for the usual range of air contents. This study is proposed to estimate the plane spacing factor by calculation of simplicity. The plane spacing factor need two parameters that are air content and numbers of air voids in the hardened concrete. Those obtained from the standard air-void system analysis of the ASTM C 457. The equation is valid for all values of paste-to-air ratio because the estimation of paste content is unnecessary at the using ASTM C 457. The plane spacing factor yields a similar estimate of the standard spacing factor.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2005년도 제31회 KOSCO SYMPOSIUM 논문집
• /
• pp.314-319
• /
• 2005

In this study, the combustion characteristics were investigated with the variation of design factors on multiple slit gas burner. The design factors consist of slit height, width, spacing, and inner length. The combustion characteristics were made analysis of the CO emission and NOx emission by using CO analyzer and NOx analyzer. The lower perimeter to area and the narrow spacing extends the lift-flame limit. The CO emission increases with the increasing perimeter to area ratio at the same condition. The NOx emission is found to be less significant with the port perimeter to area ratio. The flame interference might highly depend on the spacing and port perimeter to area ratio, and it also affects the burner performance.

• Geomechanics and Engineering
• /
• 제5권4호
• /
• pp.299-312
• /
• 2013

The horizontal pullout capacity of a group of two vertical strip plate anchors, placed along the same vertical plane, in a fully cohesive soil has been computed by using the lower bound finite element limit analysis. The effect of spacing between the plate anchors on the magnitude of total group failure load ($P_{uT}$) has been evaluated. An increase of soil cohesion with depth has also been incorporated in the analysis. For a weightless medium, the total pullout resistance of the group becomes maximum corresponding to a certain optimum spacing between the anchor plates which has been found to vary generally between 0.5B and B; where B is the width of the anchor plate. As compared to a single plate anchor, the increase in the pullout resistance for a group of two anchors becomes greater at a higher embedment ratio. The effect of soil unit weight has also been analyzed. It is noted that the interference effect on the pullout resistance increases further with an increase in the unit weight of soil mass.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.193-197
• /
• 2005

Influences of microstructure on high-cycle fatigue (HCF) limit of high carbon $(>0.7wt.\;\%)$ steel filaments used for tires have been investigated. A series of the fatigue tests was carried out depending on carbon content by using Hunter-type tester at a frequency of 60 Hz at a tension/compression stress of 900 to 1500 MPa. Microstructural changes of the filaments were identified in the lateral direction by using transmission electron microscopy (TEM). It was found that the mechanical properties, such as fatigue limit and tensile strength, were improved with increasing carbon content, which was mainly attributed to decreased lamellar spacing and cementite thickness. However, the fatigue ratio, which is defined as the ratio of the fatigue limit to the tensile strength, was reduced in a higher carbon range of 0.8 to $0.9\;wt.\%$, while the fatigue ratio was nearly constant in a lower carbon range of 0.7 to $0.8\;wt.\%$. Overall mechanical properties of the filaments, depending on carbon content, have been discussed in terms of the microstructural parameter change of lamellar spacing and cementite thickness. In addition, the variation of cementite morphology on the fatigue crack propagation of high carbon $(0.9wt.\;\%)$ filaments will be discussed.

• Structural Engineering and Mechanics
• /
• 제77권3호
• /
• pp.329-342
• /
• 2021

In this paper, the effect of different steel bar configurations on the quasi-static punching and impact response of concrete slabs was studied. A total of forty RC square slab specimens were cast in two groups of concrete strengths of 40 and 63 MPa. In each group of twenty specimens, ten specimens were reinforced at the back face (singly reinforced), and the remaining specimens were reinforced on both faces of the slab (doubly reinforced). Two rebar spacing of 25 and 100 mm, with constant reinforcement ratio and effective depth, were used in both singly and doubly reinforced slab specimens. The specimens were tested against the normal impact of cylindrical projectiles of hemispherical nose shape. Slabs were also quasi-statically tested in punching using the same projectile, which was employed for the impact testing. The experimental response illustrates that 25 mm spaced rebars are effective in (i) decreasing the local damage and overall penetration depth, (ii) increasing the absorption of impact energy, and (iii) enhancing the ballistic limit of RC slabs. The ballistic limit was predicted using the quasi-static punching test results of slab specimens showing a strong correlation between the dynamic perforation energy and the energy required for quasi-static perforation of slabs.

• 대한기계학회논문집
• /
• 제19권10호
• /
• pp.2657-2666
• /
• 1995

In this study, the effects of design factors of finned-tube heat exchanger, such as fin spacing and fin array on the frost growth and heat exchanger performance are investigated under a frosting condition. The results show that the amount of frost, frost density and blockage ratio of air flow passage increase with decreasing fin spacing. Heat transfer rate increases momentarily at the initial stage of frosting and then decreases. After that heat transfer rate continues to increase again to reach a maximum value and then decreases dramatically. It is shown that the time required for heat transfer rate to reach a maximum value becomes shorter with decreasing fin spacing, and after a maximum value, heat transfer rate decreases very fast. The maximum allowable blockage ratio is introduced to determine the operation limit of a finned-tube heat exchanger operating under frosting condition and is obtained as a function of fin spacing. It is also shown that heat transfer rate of heat exchanger with staggered fin array increases about 17% and the amount of pressure drop of air increases about 1~2 mmH$_{2}$O, compared with those of in-line type heat exchanger under frosting condition.

• 한국도로학회논문집
• /
• 제20권3호
• /
• pp.65-73
• /
• 2018

PURPOSES : In this study, the propriety of expansion joint spacing of airport concrete pavement was examined by using weather and material characteristics. METHODS : A finite element model for simulating airport concrete pavement was developed and blowup occurrence due to temperature increase was analyzed. The critical temperature causing the expansion of concrete slab and blow up at the expansion joint was calculated according to the initial vertical displacement at the joint. The amount of expansion that can occur in the concrete slab for 20 years of design life was calculated by summing the expansion and contraction by temperature, alkali-silica reaction, and drying shrinkage. The effective expansion of pavement section between adjacent expansion joints was calculated by subtracting the effective width of expansion joint from the summation of the expansion of the pavement section. The temperature change causing the effective expansion of pavement section was also calculated. The effective expansion equivalent temperature change was compared to the critical temperature, which causes the blowup, according to expansion joint spacing to verify the propriety of expansion joint applied to the airport concrete pavement. RESULTS : When an initial vertical displacement of the expansion joint was 3mm or less, the blowup never occurred for 300m of joint spacing which is used in Korean airports currently. But, there was a risk of blow-up when an initial vertical displacement of the expansion joint was 5mm or more due to the weather or material characteristics. CONCLUSIONS : It was confirmed that the intial vertical displacement at the expansion joint could be managed below 3mm from the previous research results. Accordingly it was concluded that the 300m of current expansion joint spacing of Korean airports could be used without blowup by controling the alkali-silica reaction below its allowable limit.

• 한국지반환경공학회 논문집
• /
• 제2권4호
• /
• pp.39-50
• /
• 2001

본 연구에서는 지오그리드로 보강된 도로제방 사면에 대해 한계평형해석에 근거한 보강사면해석 프로그램인 RSS를 이용하여 보강길이와 간격의 변화에 따른 사면의 안전율 변화를 살펴보았다. 해석결과 비보강시 기준안전율을 만족하지 못하는 사면에서 보강재길이의 증가에 따라 비보강사면에 비해 최대 50~150%의 안전율이 증가되었으며 보강길이를 증가시켜도 안전율의 추가상승이 없는 한계길이를 확인하였다. 또한 동일 가상보강단면에 대하여 범용프로그램인 FLAC을 이용하여 유한차분해석을 실시하여 안정성이 확보된 사면에 발생하는 수평변위, 수평응력, 보강재의 인장력을 산출하여 보강길이의 추가적인 증가에 의한 효과를 알아보았다. 해석결과, 파괴형태는 선단파괴 또는 사면내 파괴로 나타났으며 안정성을 확보한 상태에서는 한계평형해석결과와 동일하게 보강길이의 추가적인 증가에 의한 안정성 증대효과는 미미한 것으로 나타났다.

• 한국지반환경공학회 논문집
• /
• 제20권1호
• /
• pp.43-49
• /
• 2019

본 논문에서는 쏘일네일 설계에 위상최적화 기법을 도입하여 비탈면 높이별로 필요로 하는 보강력을 최적화하였다. 최대 비탈면 높이에서의 최적설계 결과를 보강형상밀도화하여 비탈면의 높이 변화에 따라 적용 시 쏘일네일의 수평간격의 위상최적화가 가능하였다. 단계별로 비탈면 높이를 달리하여 한계평형해석을 수행하고 쏘일네일의 수평간격이 고정값일 때 초과되는 안전율을 확인하였다. 비탈면 높이에 따른 필요 보강력을 밀도화 함으로써 최적화의 과정을 효율적으로 수행할 수 있었다. 또한 쏘일네일의 축력을 보강형상밀도에 반영하기 위하여 유한요소법을 이용하여 부재력을 반영하였다. 보강형상밀도를 산정하여 비탈면 높이별로 위상최적기법을 적용 시 비탈면 높이마다 기준안전율을 만족하는 반복적인 재해석과정을 효과적으로 감소시킬 수 있어 수평간격을 위상 최적화하는 방법이 경제적인 설계에 활용도가 높을 것으로 판단된다.