• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.511-518
• /
• 2000

Characteristics of joint orientation, length, spacing and their distribution are very important factors for slope stability, Especially, the effect of joint spacing is an essential factor of slope stability. This study is to analyze the effect of joint spacing in cases of sliding and toppling, which is a typical failure mode. Joint spacing can divided into vertical spacing(spacing) and horizontal spacing(gap). And then, the spacing/length ratio of joint directly affect rock slope failure. When the ratio is below 0.05, the possibility of failure is rapidly increased. In case of toppling, the possibility of failure depends on the ratio of spacing to height of slope ratio slope. As the ratio decreases, the possibility of toppling failure increased. The critical ratio of spacing to height of slope is determined by the dip angle of the slope and the orientation of joint sets.

• Journal of Mechanical Science and Technology
• /
• 제16권11호
• /
• pp.1428-1434
• /
• 2002

The ball-on-disk type sliding tests with boundary lubricated steels were carried out to verify the effect of initial spacing in surface profiles on wear and scuffing. Three kinds of surface spacing, which are closely related with initial surface micro-cracks on sliding surfaces, were produced on AISI 1045 steel surfaces using different grinding and polishing processes. Frictional forces and time to scuffing were measured, and the shape and amount of wear particles were analyzed to compare the with original surface profiles. From the tests, it was confirmed that the size of wear particles are related closely to the original spacing of the surface profile. The time to failure and amount of wear were sensitive to the surface spacing. The wider surface spacing shows much longer sliding life and smaller amount of wear than the others. Time to scuffing was increased with increasing surface pro(lie spacing. The size of wear particles increased while the wear and wear rate K were decreased with an increase in surface spacing. After the sliding tests, surface cracks of inner parts of the wear track formed due to scuffing were observed and compared among the specimens having the different surface spacing.

• 한국도로학회논문집
• /
• 제15권3호
• /
• pp.151-157
• /
• 2013

PURPOSES : This study aims to suggest the optimal spacing between speed humps which is placed at traffic calming areas including pedestrian priority zones, school zones, and residential areas. METHODS: The study measured the operating speed of vehicles passing through two successive humps by using laser gun in 0.2 seconds interval, and analysed the basic statistical characteristics of speeds data to have an insight on the relationship between spacing and speed. Assumption was made to derive the maximum spacing within which two successive humps influence each other. RESULTS: The statistically significant model explaining the relationship between spacing and 85th percentile speed of vehicles was derived as well as the maximum spacing maintained in order to take the benefits of successive installation of humps. CONCLUSIONS: Spacing of 20 meters was suggested to achieve the widely accepted target speed of 30 km/h in traffic calming zone, and spacing of 70 meters was suggested as a maximum spacing. The comparison across the studies were made and empirical reasoning the difference of results between studies was discussed as well as the future studies.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제28회 KOSCO SYMPOSIUM 논문집
• /
• pp.183-191
• /
• 2004

The burning characteristics of interacting droplets with internal circulation in a convective flow are numerically investigated at various Reynolds numbers. The transient combustion of 2-dimensionally arranged droplets, both the fixed droplet distances of 5 radii to 40 radii horizontally and 4 radii to 24 radii vertically, is studied. The results obtained from the present numerical analysis reveal that the transient flame configuration and retardation of droplet internal motion with the horizontal or vertical droplet spacing substantially influence lifetime of interacting droplets. At a low Reynolds number, lifetime of the two droplets with decreasing horizontal droplet spacing increases monotonically, whereas their lifetime with decreasing vertical droplet spacing decreases due to flow acceleration. This flow acceleration effect is reversed when the vertical droplet spacing is smaller than 5 radii in which decreasing flame penetration depth causes the reduction of heat transfer from flame to droplets. At a high Reynolds number, however, lifetime of the first droplet is hardly affected by either the horizontal droplet spacing or flow acceleration effect. Lifetime with decreasing vertical droplet spacing increases due to reduction of flame penetration depth. Lifetime of interacting droplets exhibits a strong dependence on Reynolds number, the horizontal droplet spacing and the vertical droplet spacing and can be con-elated well with these conditions to that of single burning droplet.

• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.997-1004
• /
• 2000

The experiments were conducted by using water and paraffin slurry to investigate the effect of a chip spacing in the multichip module on the cooling characteristics from an in-line $4{\times}3$ array of discrete heat sources which were flush mounted on the top wall of a channel. The experimental parameters were chip spacing in a multichip module, heat flux of simulated VLSI chip, mass fraction of paraffin slurry, and channel Reynolds number. The removable heat flux at the same chip surface temperature decreased as the chip spacing decreased at the first and fourth rows. The local heat transfer coefficients for the paraffin slurry were larger than those for water, and the chip spacing on the local heat transfer coefficients for paraffin slurry influenced less than that for water. The enhancement factor for paraffin slurry showed the largest value at a mass fraction of 5% regardless of the chip spacing, and the enhancement factors increased as the chip spacing decreased. This means that the paraffin slurry is more effective than water for cooling of the highly integrated multichip module.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1125-1130
• /
• 2005

This paper presents a method for inter-sheet spacing control in a flexible media handling device. In order to verify the performance of inter-sheet spacing control by experiment, system of section structure is introduced in the first place. In the introduced system, each section is driven by different servo motor for independent section freedom. And suitable inter-sheet spacing control algorithm that is more optimal than conventional inter-sheet spacing control algorithm is proposed. Finally experiments are performed to confirm the performance of inter-sheet spacing control. And two inter-sheet spacing control algorithms, conventional and proposed, are compared with each other.

• ETRI Journal
• /
• 제43권6호
• /
• pp.1049-1057
• /
• 2021

Automatic spacing in Korean is used to correct spacing units in a given input sentence. The demand for automatic spacing has been increasing owing to frequent incorrect spacing in recent media, such as the Internet and mobile networks. Therefore, herein, we propose a transformer encoder that reads a sentence bidirectionally and can be pretrained using an out-of-task corpus. Notably, our model exhibited the highest character accuracy (98.42%) among the existing automatic spacing models for Korean. We experimentally validated the effectiveness of bidirectional encoding and pretraining for automatic spacing in Korean. Moreover, we conclude that pretraining is more important than fine-tuning and data size.

• 대한토목학회논문집
• /
• 제31권6A호
• /
• pp.449-456
• /
• 2011

Power에 의해 제안된 간격계수는 기하학적 모델을 바탕으로 구성된 공극 간격의 평균적 개념으로, 실제 콘크리트의 공극구조 특성을 반영하는데 한계가 있다. 이에 본 연구에서는 간격계수의 한계를 극복하기 위해 콘크리트의 실제 공극구조 특성을 반영한 간격분포지수를 제안하였으며, 간격계수와의 비교분석을 통해 이 지수에 대한 평가를 수행하였다. 본 연구결과, 간격계수는 AE제 첨가량이 증가함에 따라 감소하는 경향을 나타내었으나, 간격분포지수는 증가하는 경향을 나타내었다. 이는 간격분포지수가 간격분포곡선의 면적 값을 이용한 것으로 간격별 빈도수가 높은 것이 크게 나타나기 때문이다. 또한 간격계수 $300{\mu}m$이하의 범위에서 간격분포지수는 더 넓은 범위를 나타내었다. 이에 간격분포지수 사용 시 내구성지수 80% 이상이 되는 임계지점을 찾는데 좀 더 용이할 것으로 예상되며, 콘크리트의 내구성을 추정하는데 있어 좀 더 신뢰성 있는 분석이 가능할 것으로 판단된다. 간격분포지수는 공극 간격분포의 면적 값으로 실제 콘크리트의 공극구조특성을 반영한 지수이다. 추후, 동결융해실험 결과와의 비교를 통해 추가적인 검증연구가 필요할 것으로 판단된다.

• 한국토양비료학회지
• /
• 제51권2호
• /
• pp.79-89
• /
• 2018

Subsurface drip irrigation (SDI) system is considered one of the most effective methods for water application. A 2-year field study was conducted to investigate the effect of SDI systems with various dripline spacing (0.7 or 1.4 m) and position (under furrow or ridge) on soybean (Glycine max L.) production at a sandy-loam soil in Miryang, South Korea. For 2016-2017, average grain yield in SDI irrigated plots, $3.16Mg\;ha^{-1}$, was statistically greater than rainfed irrigated plot ($2.63Mg\;ha^{-1}$). Soybean grain yield averaged $3.25Mg\;ha^{-1}$ for the 0.7 m dripline spacing and $3.07Mg\;ha^{-1}$ for the 1.4 m spacing for the two-year period compared to a rainfed irrigated average of $2.63Mg\;ha^{-1}$ for the same period. Soybean treated with SDI system had significantly greater values of normalized difference vegetation index and stomatal conductance, indicating that soybean plants in SDI plots had greater photosynthetic and stomatal activity due to the higher water availability in soil. Irrigation water use efficiency (IWUE) was greatest in the plot of 0.7 m spacing installed under ridge position than any other plot across growing season. Average soil water content in plots with 0.7 m dripline spacing was $0.21m^3\;m^{-3}$ at 5 cm depth layer, which was 45% greater compared to the plots with 1.4 m spacing, even though the gross irrigation amounts were greater in 1.4 m spacing plots. It is concluded that wide dripline spacing (1.4 m) is probably the more economical installation design for SDI system compared to 0.7 m spacing in this study soil because the initial cost for dripline may be reduced with wide spacing design, even though the IWUE is greater in the plot of 0.7 m dripline spacing.

• 한국연소학회지
• /
• 제8권2호
• /
• pp.17-26
• /
• 2003

The objective of present study is to understand the interaction of burning droplets in air stream for various droplet arrangement. The unsteady combustion of linearly arranged droplets with a convective flow has been studied numerically. The droplets with spacing of $5R_0\;to\;40R_0$ horizontally and with spacing of $4R_0\;to\;16R_0$ vertically are studied. The effects of Reynolds number, horizontal spacing, and vertical spacing on the interaction of burning droplets are examined. The results indicate that the droplet burning behavior is influenced by Reynolds number and relative location of droplets in the array. The interaction of droplets is increased for arrays with smaller droplet spacing. The vaporization of droplets in the array is varied with both horizontal and vertical spacing exponentially.