• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.20-21
• /
• 2008

Ferroelectric vinylidene fluoride-trifluoroethylene ($VF_2$-TrFE) copolymer films were directly deposited on degenerated Si ($n^+$, 0.002 $\Omega{\cdot}cm$) using by dip coating method. A 1 ~ 3 wt% diluted solution of purified vinylidene fluoride-trifluoroethylene ($VF_2$:TrFE=70:30) in a dimethylformamide (DMF) solvent were prepared and deposited on silicon wafers using dip coating method for 10 seconds. After Post-Annealing in a vacuum ambient at 100~200 $^{\circ}C$ for 60 min, upper aluminum electrodes were deposited by thermal evaporation through the shadow mask to complete the MFS structure. The ferroelectric $\beta$-phase peak of films, depending on the annealing temperature, started to show up around $125^{\circ}C$, and the intensity of the peak increased with increasing annealing temperature. Above $175^{\circ}C$, the peak started to decrease. The C-V characteristics were measured using a Precision LCR meter (HP 4284A) with frequency of 1MHz and a signal amplitude of 20 mV. The leakage-current versus electric-field characteristics was measured by mean of a pA meter/DC voltage source (HP 4140B).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.67-67
• /
• 2008

Application of organic materials with low cost, easy fabrication and advantages of flexible device are increasing attention by research work. Recently, one of them, organic solar cells were rapidly increased efficiency with regioregular poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyricacidmethylester (PCBM) used typical material. To increased efficiency of organic solar cell has tried control of domain of PCBM and crystallite of P3HT by thermal annealing and solvent vapor annealing. [4-6] In those annealing effects, be made inefficiently efficiency, which is increased fill factor (FF), and current density by phase-separated morphology with blended P3HT and PCBM. In addition, increased conductivity by modified hole transfer layer (HTL) such as Poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS), increased both optical and conducting effect by titanium oxide (TiOx), and changed cathode material for control work function were increased efficiency of Organic solar cell. In this study, we had described effect of organic photovoltaics by conductivity of interlayer such as PEDOT:PSS and TCO (Transparent conducting oxide) such as ITO, which is used P3HT and PCBM. And, we have measured with exactly defined shadow mask to study effect of solar cell efficiency according to conductivity of hole transfer layer.

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.35-40
• /
• 2018

다양한 디바이스 응용분야에 블록공중합체가 사용되기 위해, 블록공중합체의 형상을 제어하기 위한 간단하면서도 실용적인 합성방법이 필요하다. 하지만 콜로이드성의 형판을 사용하는 기존의 방식은 공정이 복합하고 비용이 많이 발생하여, 고순도의 코어-쉘 나노입자를 대량생산하기에 적합하지 않다. 본 논문에서 PS-b-PDMS 블록공중합체를 담금어닐링하여, 20 nm 이하크기를 가지는 PS가 봉입된 코어-쉘 구조의 $SiO_x$나노입자를 합성하였다. 또한, 어닐링 공정에 사용되는 헵테인과 에탄올의 혼합비율이 자기조립된 PS-b-PDMS 블록공중합체 나노입자의 형상에 어떠한 영향을 미치는지 분석하였으며, 최적의 담금어닐링 조건에서 나노입자가 worm-like구조로 변화하는 것을 확인하였다. 이러한 파우더 합성법은 다른 용매기반의 블록공중합체 합성방법에 응용이 가능할 것으로 생각되며, 새로운 가이드라인을 제공할 것으로 예상된다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.206.1-206.1
• /
• 2015

최근에 금속산화물을 증착하는 방법으로 용액공정이 주목 받고 있다. 용액 공정은 대기압에서 매우 간단한 방법으로 복잡한 공정과정을 요구하지 않기 때문에 박막을 경제적으로 간단하게 형성할 수 있다. 하지만 용액공정을 통해 형성한 박막에는 소자의 특성을 열화 시키는 solvent와 탄소계열의 불순물을 많이 포함하고 있어 고온의 열처리가 필수적이다. 박막의 품질을 향상시키기 위해서 다양한 열처리 방법들이 이용되고 있으며, 일반적인 열처리 방법으로는 furnace를 이용한 conventional thermal annealing (CTA)이 많이 이용되고 있다. 하지만, 최근에는 microwave를 이용한 공정이 주목 받고 있다. Microwave energy는 CTA보다 효과적으로 비교적 낮은 온도에서 높은 열처리 효과를 나타낸다. 본 실험은 n-type Silicon 기판에 solution-ZrO2 산화막을 형성 후, oven baking을 한 뒤, CTA와 microwave를 이용하여 solvent와 불순물을 제거 하였다. 전기적 특성을 확인하기 위해 solution ZrO2 산화막 위에 E-beam evaporator를 이용해 Ti 금속 전극을 증착하여 Metal-Oxide-Semiconductor (MOS) capacitor를 제작하였다. 다음으로, PRECISION SEMICONDUCTOR PARAMETER ANALYZER (4156B)를 이용하여, capacitance-voltage (C-V) 특성 및 current-voltage (I-V) 특성을 비교하였다. 다음으로, CTA를 통하여 제작한 소자와 전기적 특성을 비교하였다. 그 결과, Microwave irradiation으로 열처리한 MOS capacitor 소자에서 capacitance 값과 flat band voltage, hysteresis 등이 개선되는 효과를 확인하였다. Microwave irradiation 열처리는 100oC 미만의 온도에서 공정이 이루어짐에도 불구하고 시료 내에서의 microwave 에너지의 흡수가 CTA 공정에서의 열에너지 흡수보다 훨씬 효율적으로 이루어지며, 결과적으로 ZrO2 용액의 불순물과 solvent를 낮은 온도에서 제거하여 고품질 박막 형성에 매우 효과적이라는 것을 나타낸다. 따라서, microwave irradiation 열처리 방법은 비정질 산화막이 포함되는 박막 transistor 소자 제작에 대하여 결정적인 열처리 방법이 될 것으로 기대한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.432-433
• /
• 2012

Polymer solar cells are fabricated using electrospray (e-spray) deposition process. It shows comparable performance with reference devices, and has different characteristics according to the thickness of the active layer: In the case of the devices with higher fill factor, it shows relatively lower current density, and vice versa. These films are characterized by atomic force microscopy measurement. The results indicate that the comparable power conversion efficiency made by e-spray results from the 'solvent annealing effect' by process conditions and the different thin film property is caused by the degree of self-organization of the polymer.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1993년도 추계 총회 및 학술발표회
• /
• pp.7-12
• /
• 1993

Preparation of asymmetric polyimide membranes by the phase inversion process was investigated to develop ultrafiltration, reverse osmosis and pervaporation membranes for organic solutions, using a commercially available solvent-soluble polymaide. The influences of the various factors such as the composition of a cast solution, casting conditions, gelating solutions and others on membrane structure and performance were studied in detail, and it was made clear that a wide variety of asymmetric polyimide membranes ranging from UF to RO for organic solutions could be prepared from the aromatic polyimide used. It was also found that the chemical stability and separation performance of the asymmetric polyimide membranes could be improved by annealing in a liquid or a vacuum at above 200$\circ$. The membrane annealed at 300$\circ$ in a vacuum exhibited the separation factor $\alpha(H_2O/EtOH)$ of 900 with the flux of 1.0 kg/$m^2\cdot h$ at 60$\circ$C for an aqueous ethanol solution of 95 vol%.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.276-276
• /
• 2013

Time-Of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) and Atomic Force Microscopy (AFM) are the useful instruments to measure nanostructures of material surfaces. Surface pattern formation in blending homopolymer and diblock copolymer films was investigated as a function of film thickness and annealing conditions. In this study, surface structures of blending homopolymer [deuterated polystyrene (Mn 20,000), poly (methyl methacrylate) (Mn 18,000)] and diblock copolymer [Poly (deuteratedstyrene(d8)-b-methyl methacrylate) (Mn 19,500-18,100)] films were observed. The AFM result indicated that the nanostructures and film thickness depended on temperature, concentration and solvent. TOF-SIMS depth profiling was obtained for the lamellar morphology of symmetric dPS-b-PMMA which is found to orient parallel to the surface of the substrate. Elemental and molecular depth profiles measured in the negative ion mode by a Cs+ primary ion beam demonstrate variations in hydrogen, deuterium, carbon, oxygen, hydrocarbons and deuterated hydrocarbons within the diblock copolymer according to the depth.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.188-188
• /
• 2006

We demonstrate two very simple and fast routes to fabricating ordered micro/nanopatterns of polymers over large areas on various substrates using controlled dewetting. The first method is based on utilizing microimprinting to induce the local thickness variation of an initially inverted bilayer which allows the controlled dewetting and partial layer inversion upon subsequent thermal annealing. In the second method, the self assembly of block copolymer was controlled on a chemically micropatterned surface produced by microcontact printing, being combined with its solvent vapor treatment. The kinetically driven, non-lithographical nanopattern structures were easily fabricated over large area by these approaches.

• 멤브레인
• /
• 제3권3호
• /
• pp.117-125
• /
• 1993

셀룰로오스 아세테이트(CA) 소재로 역삼투막을 제조하여 각종 제막조건에 의한 막성능에 미치는 영향인자를 조사하였다. 제막 용액조성으로 CA, formamide, acetone과 2-methoxyethanol을 사용하여 평판형 막을 만들고, 투과유속 및 배제율을 측정하였다. 특성 측정 인자로서 고분자 농도, 증발시간, 열처리 온도 및 처리 시간, 조작압력, 공급액의 농도 등을 변화시켜 막에 대한 영향을 연구하였다. 또한 제조된 막을 사용하여 역삼투 모델식에 적용하여 각각의 파라메타를 계산하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1414-1416
• /
• 2001

Crack-free and homogeneous compact and epitaxial lead zirconate titanate(PZT) ferroelectric thin films with perovsikte structure have been prepared by sol-eel method. Tetrabutyl titanate, lead acetate and zirconium nitrate are used as raw materials. Glacial acetic acid is used as a catalyst. Ethylene glycol monoethyl ether is used as a solvent. The annealing temperatures of th thin films are 600~900$^{\circ}C$. The values of the remanent polarization Pr, and the coercive field $E_c$, of the PZT ceramic thin films are 46, 35 ${\mu}C/cm^2$ respectively.