• ETRI Journal
• /
• v.27 no.2
• /
• pp.181-187
• /
• 2005

Alkoxy-substituted poly(spirobifluorene)s and their copolymers with a triphenylamine derivative have been synthesized by Ni(0)-mediated polymerization. The polymers were well soluble in common organic solvents. Pure blue-light emissions without the long wavelength emission of poly(fluorene)s have been observed in the fluorescence spectra of polymer thin films. The light emitting diodes with a device configuration of ITO/PEDT:PSS(30 nm)/polymer(60 nm)/LiF(1 nm)/Al(100 nm) have been fabricated. The electroluminescence spectra showed the blue emissions without the long wavelength emission as observed in the fluorescence spectra. The relatively poor electroluminescence quantum yield of the homopolymer (0.017% @ 20 $mA/cm^{2}$) with color coordinates of (0.16, 0.07) has been improved by the introduction of triphenylamine moiety, and the copolymer with derivative exhibited an electroluminescence quantum yield of 0.15 % at 20 $mA/cm^{2}$ with color coordinates of (0.16, 0.08). Moreover, the introduction of polar side chains to the spirobifluorene moiety enhanced the device performance and led to the quantum yields of 0.6 to 0.7 % at 20 $mA/cm^{2}$, although there was some expense of color purities.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1638-1641
• /
• 2008

We have investigated the effectiveness of a gravure printing method for the fabrication of organic light-emitting diode (OLED) and Organic Thin Film Transistor (OTFT). Printing of the organic layers was performed with a small-scale gravure coating machine, while the metallic layers were vacuum-evaporated. Devices with gravure-printed layers are at least comparable with the spin-coated devices. Effects of the solvent formulation and surface energy mismatch between the organic layer materials on the printed patterns and device performance were discussed. We will present the initial design and experimental data of OTFT fabricated by roll-type soft contact transfer process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1361-1363
• /
• 2005

In this paper, we report on the performance stability of solution processible OTFT devices with Au/Ti and ITO source-drain (S/D) electrodes. It appears that the contact resistance of the S/D electrode strongly affects the stability of OTFT devices. Interestingly, the devices with the Au/Ti electrode showed lower mobility than those with the ITO (S/D) devices. The field effect mobilities of the devices with the Au/Ti and ITO electrodes were 0.06, and $0.44cm^2/Vs$, respectively. However, the mobility of the device with the Au/Ti electrode was increased up to $0.26cm^2/Vs$ after 2 weeks, while the mobility of the device with ITO electrode was slightly decreased down to $0.41cm^2/Vs$. The experimental data show us that ITO could be used as the S/D electrode for low-cost OTFT devices.

• Current Photovoltaic Research
• /
• v.8 no.2
• /
• pp.60-65
• /
• 2020

In perovskite solar cells with planar heterojunction configuration, selection of proper charge-transporting layers is very important to achieve stable and efficient device. Here, we developed solution processible Cu doped NiO_x (Cu:NiO_x) thin film as a hole-transporting layer (HTL) in p-i-n structured methylammonium lead trihalide (MAPbI₃) perovskite solar cell. The transmittance and thickness of NiO_x HTL is optimized by control the spin-coating rate and Cu is additionally doped to improve the surface morphology of undoped NiO_x thin film and hole-extraction properties. Consequently, a perovskite solar cell containing Cu:NiO_x HTL with optimal doping ratio of Cu exhibits a power conversion efficiency of 14.6%.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.843-845
• /
• 2009

A polymeric host for triplet emitters composed of N-alkylcarbazole and tetramethylbenzene units was successfully synthesized. Efficient energy transfer was observed between this polymeric host and green phosphorescent dyes. The device fabricated using 5 wt% green 1 in the polymeric host as the emitting layer showed the best performance. Thin films of this host-guest system, exhibiting clear stripe patterns could be prepared through the LITI process. The patterned films were then used to fabricate electrophosphorescent devices, which show performance characteristics similar to those of spin-coated devices. The new host material is a good candidate to be used in polymer-based full-color electrophosphorescent light-emitting displays.

• Journal of the Korean Electrochemical Society
• /
• v.6 no.2
• /
• pp.113-118
• /
• 2003

Processible polyaniline (PAM) dispersions consisting of polyaniline micro-particles, cyclohexanone, and a polymeric surfactant were prepared in a micro-milling machine with various mixing conditions. The electrochemical properties of the dispersion film coated on Pt electrode were investigated by cyclic voltammetry (CV). The electrochemistry of the PAM dispersion coatings was basically similar to a pure PAM coating based on the results of CV. The results of polarization measurements and open circuit potential measurements carried out in $3\;wt.\%$ NaCI solution showed increase in corrosion potential when the PANI dispersion coatings applied on steel surface. Variation of open circuit potential $(OCP,\;V_{OC})$ of the dispersion coating/steel electrodes was observed, which differed with milling conditions. The results demonstrated practical use of the conducting polymer dispersion as a coating material for corrosion prevention of steel.

• Korean Chemical Engineering Research
• /
• v.51 no.6
• /
• pp.774-779
• /
• 2013

We synthesized the solution processible monodispersed $TiO_2$ crystalline nano-sol with ~ 5 nm in size by sol-gel method. Through the spin-coating of crystalline $TiO_2$ nano-sol at low processing temperature, we could make even blocking interlayer on the rough FTO transparent electrode substrate. The rough FTO surface could be gradually smoothed by the spin-coating of nano-crystalline $TiO_2$ sol based blocking interlayer. The 1, 2.5, 5, and 10 wt% of nanocrystalline $TiO_2$ sol formed 29, 38, 62, and 226 nm-thick of blocking interlayer in present experimental condition, respectively. The 5 and 10 wt% of $TiO_2$ nano-sol could effectively fill up the valley part of bare FTO with 48.7 nm of rms (root mean square) roughness and consequently enabled the ZnO to be grown to vertically aligned one dimensional nanorods on the flattened blocking interlayer/FTO substrate.