• Journal of the Korean Society of Food Science and Nutrition
• /
• v.24 no.5
• /
• pp.811-815
• /
• 1995

Effect of deamidation with Neutrase on the solubility of bovin serum albumin(BSA), egg albumin(EA), soy protein isolate(SPI) was investigated. Solubility of deamidated BSA in distilled water was decreased from 98% to 83% against native BSA at pH 4~8, minimum solubility of deamidated BSA was pH 6. Solubilities of native BSA and deamidated BSA in 0.2M NaCl solution were shown 100% as compared greately decreasing both solubilities in 1.0M NaCl at acidic pH. According to deamidation, solubility of EA in distilled water was increased below pH 4 and above pH 6, while solubility of EA in NaCl solution was decreased by deamidation at acidic pH. Solubility of SPI in distilled water was greately increased by deamidation at overall pH, deamidation was increased solubility in NaCl solution above pH 5. There was, however, no difference on solubility by deamidation below pH 5.

• Journal of Environmental Science International
• /
• v.13 no.3
• /
• pp.289-295
• /
• 2004

The objective of this study is to delineate removal efficiency of the MTBE in solution by $TiO_2$ photocatalytic degradation as a function of the following different experimental conditions: Initial concentration of MTBE, air flow rate in solution, $H_2O_2$ dosage and pH of the solution. Photodegradation rate was increased with decreasing initial concentration of MTBE. The removal efficiency was 82% after 180 min in the case of MTBE concentration of 100 mg/L but 100% after 180 min in the case of 20 mg/L. Removal efficiency was increased with increasing pH, $H_2O_2$ dosage and air flow rate in solution.

• Bulletin of the Korean Chemical Society
• /
• v.7 no.2
• /
• pp.137-142
• /
• 1986

The luminescence spectra of $Ru(bpy)_3^{2+}$ in poly(methacrylic acid) (PMA) solutions varied sensitively with pH. At pH < 5.5, the emission intensity increased with pH up to 4 times, while it decreased with pH beyond the pH. The enhanced emission intensity was accompanied by blue-shift of the emission maxima as much as 15 nm. The enhancement of emission intensity was attributed to the restricted rotational mobility of ligand of the cation bound to densely coiled PMA molecules at pH < 5.5. The sharp decrease in emission intensity with increasing pH near pH 5.6 was accounted for conformational transition of the polymer to more extended structure, which was also revealed in viscosity measurement. The enhancement of emission intensity became higher as NaCl concentration of the solution increased. The binding constant of $Ru(bpy)_3^{2+}$ with two carboxylate groups of PMA was calculated as $2{\times}10^5\;M^{-1}$ in 0.1 M NaCl at pH 5.2. The pH dependence of luminescence quenching rate of $Ru(bpy)_3^{2+}$ by $Cu^{++}$ also showed maximum near pH 5, and the rate was more than $10^3$ times higher than that in water, whereas the maximum enhancement of quenching rate (about 20 times) in poly(acrylic acid) (PAA) solution occurred at pH 4.5. On the other hand, the pH dependence for neutral water soluble nitrobenzene (NB) exhibited opposite trend to that of $Cu^{++}$. The quenching constant vs pH curve for $MV^{++}$ was composite of those for $Cu^{++}$ and NB. The anomalous high quenching rate for $Cu^{++}$ in PMA solution at pH < 5.5 was attributed to the binding of $Ru(bpy)_3^{2+}$ and $Cu^{++}$ to the same region of PMA, when it conforms densely coiled structure in the pH range. The observation of mininium quenching rate for NB near pH 5.5 indicated that the $Ru(bpy)_3^{2+}$ bound to the densely coiled PMA is not accessible by NB, which is in bulk water phase. The composite nature of the pH dependence of quenching rate for $MV^{++}$ in PMA solution was attributed to the smaller binding affinity of the cation to PMA, compared to that of $Cu^{++}$. The sharp, cooperative conformational transition with pH observed in PMA was not revealed in PAA. But, the pH dependence of quenching rates in this polymer reflected increased charge density and, thus, binding of cations to the polymer, and expansion of the polymer chain with pH.

• Economic and Environmental Geology
• /
• v.34 no.3
• /
• pp.301-306
• /
• 2001

Column tests were conducted to investigate the optimal condition of surfactant solution pH that can affect the removal efficiency in surfactant-assisted remediation. Toluene and 1,2,4-trichlorobenzene were chosen as the model hydrophobic substances. Two Iowa soils, Fruitfield sand and Webster clay loam, were leached with solutions of 4%(v/v) sodium diphenyl oxide disulfonate (DOSL, trade name Dowfax 8390), or 4%(v/v) trideceth-19-carboxylic acid (TDCA, trade name Sandopan JA36), or 4% (v/v) octylphenoxypoly ethoxyethanol (OPEE, trade name Triton X100). The test results revealed that a maximum removal of toluene and 1,2,4-trichlorobenzene was obtained at pH 10 of surfactant solution, and maximum recoveries of added toluene (94%) or 1 ,2,4- trichlorobenzene (97 %) were obtained for DOSL surfactant solution in Fruitfield sandy soil column. Increased removal efficiency by pH control of both toluene and 1,2,4trichlorobenzene was 16% and 20% for DOSL with Fruitfild sandy soil, respectively. In addition, the maximum recoveries of added toluene or I ,2,4-trichlorobenzene were 89% and 93% for DOSL surfactant solution in Webster clay loam soil column. The maximum increase of toluene and 1,2,4-trichlorobenzene removal was 26% and 19% for DOSL with Webster clay loam soil, respectively. These experimental results indicate that maintaining a high pH surfactant solution in surfactant-assisted remediation is desirable for efficient removal of NAPLs from contminated soils.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.548-554
• /
• 2016

In this study, semi-aqueous solutions containing carboxylic acids such as oxalic acid (OA), lactic acid (LA) and citric acid (CA) were formulated for the removal of copper etching residues produced at the interconnection process, and their characteristics were analyzed. Carboxylic acids in the solutions were apt to form various copper complexes according to the value of pH. Semi-aqueous solution containing 10 wt% CA showed the lowest etching rate of copper in the range from pH2 to pH7 and the highest selectivity in the range of pH 2 to pH 4. However, the cleaning solution containing 10 wt% LA revealed the superior selectivity at the range from pH 5 to pH 7. Appropriate selection of carboxylic acid should be required to improve the performance of cleaning solution. In the case of CA, the etching selectivity of copper oxide complex to copper was increased with the concentration of CA in the solution, when the solutions contain over 5 wt% CA, the copper interconnection layer has a metallic copper surface more than 88% in the area. The result shows that CA contained semi-aqueous solution has a relatively good cleaning ability.

• Nuclear Engineering and Technology
• /
• v.18 no.3
• /
• pp.194-199
• /
• 1986

The behavior of micro amount of Am in aqueous solution were investigated with centrifugation method as a function of pH. In the studies described here, equilibration times were extended to 2-3 weeks to know the aging effect in radiocolloid formation. Also, the effect of the addition of foreign materials, e. g. silica gel and Fe$^{3+}$ were examined as well as the effect of presence of concentrated electrolyte. In the results, Am appeared to be rapidly adsorbed on to impurity particles for pH < 6 and probably on the container walls by an ionic sorption process. The addition of foreign material increased the fraction of Am while the addition of concentrated electrolyte hindered the process. For pH > 7 Am behaved quite differently than for pH < 6. There appeared to be rapid sorption of some Am from solution probably on the container walls followed by partial desorption that occurred over a period of 1-2 days.s.

• Tribology and Lubricants
• /
• v.20 no.2
• /
• pp.97-101
• /
• 2004

This paper reports the studies on the wear-corrosion behavior of Al-Mg alloy in various pH environments. In various pH of sea water, corrosion and wear-corrosion loss of Al-Mg alloy were investigated. Also, the polarization test of Al-Mg alloy using potentiostat/galvanostat was carried out. And the rubbed surface of Al-Mg alloy using scanning electron micrographs after wear-corrosion test was examined in various pH values of sea water. The main results are as following : The polarization resistance of Al-Mg alloy in pH 4 solution is higer than that in pH 6.7 solution, and the corrosion current density in pH 4 is controlled than in pH 6.7 solution. The wear-corrosion loss of Al-Mg alloy with lowering pH becomes sensitive. As the oxide product of Al-Mg alloy appears granular structure and exholiation phenomenon, wear-corrosion loss of Al-Mg alloy increases.

• Textile Coloration and Finishing
• /
• v.11 no.4
• /
• pp.24-30
• /
• 1999

Cotton fabric was dyed with indigo at different pHs, dye concentrations, and repeated dyeings. And the K/S value and dye uptake of the dyed materials at those conditions were determined. The decrease of pH during the reduction process of indigo stock solution was observed. As a result the decrease of pH of the dye stock solution depended on the dye concentration and initial pH. The highest K/S value was shown at fabric dyed at pH 11 and the relationship between K/S value and dye uptake depended on initial pH of reduction bath and the slope was lower as the pH increased to 13.

• Korean Journal of Mathematics
• /
• v.4 no.1
• /
• pp.51-64
• /
• 1996

In this paper we investigate the existence of weak solutions of a nonlinear beam equation under Dirichlet boundary condition on the interval $-\frac{\pi}{2}<x<\frac{\pi}{2}$ and periodic condition on the variable $t$, $u_{tt}+u_{xxxx}=p(x,t,u)$. We show that if $p$ satisfies condition $(p_1)-(p_3)$, then the nonlinear beam equation possesses at least one weak solution.

• Journal of the Korean Mathematical Society
• /
• v.44 no.3
• /
• pp.585-603
• /
• 2007

The author studies the local $H\ddot{o}lder$ convergence of the solution to an evolution equation of p-Ginzburg-Landau type, to the heat flow of the p-harmonic map, when the parameter tends to zero. The convergence is derived by establishing a uniform gradient estimation for the solution of the regularized equation.