• Journal of the Korean Wood Science and Technology
• /
• 제17권3호
• /
• pp.8-19
• /
• 1989

본 연구(硏究)는 장기간 조림장려수종(造林奬勵樹種)으로서 전국에 식재되어 이미 충분한 공급량을 확보하고 있으나 품질이 불량해서 외면당하고 있는 리기다소나무 및 낙엽송과 우리나라 천연자생수종(天然自生樹種)이며 임목축적량이 많은 소나무를 공시목(供試木)으로 선정하여 곡목가공분야(曲木加工分野)에서 널리 이용되고 있는 증자법(蒸煮法)에 의한 소재(素材)휨가공성(加工性)을 조사하였다. 이 때 사용된 휨가공시편(加工試片)의 일반크기는 두께와 폭 15mm, 길이 350mm로 제작하였으며 시편(試片)의 함수율(含水率)은 15+1%로 조습(調濕)된 기건시편(氣乾試片)을 사용하였다. 본 연구(硏究)에서 얻은 결과(結果)를 요약(要約)하면 다음과 같다. (1) 변재와 심재별 최소곡률반경(最小曲率半徑)은 각각 소나무 300-260mm 및 320-260mm, 리기다소나무 280-240mm 및 240-220mm, 낙엽송 340-300mm 및 320-300mm로서 소나무는 변재, 리기다소나무와 낙엽송은 심재의 휨가공성(加工性)이 다소 양호(良好)하였다. (2) 판목재(板目材), 추정목재(追柾目材) 및 정목재별(柾目材別) 최소곡률반경(最小曲率半徑)은 각각 소나무 300-260mm, 320-260mm 및 280-240mm, 리기다소나무 280-240mm, 280-240mm 및 260-220mm, 낙엽송 320-300mm, 360-340mm 및 300-320mm로서 대체로 정목재(柾目材)의 휨가공성(加工性)이 가장 양호(良好)하였다. (3) 휨가공(加工)을 위한 소나무, 리기다소나무 및 낙엽송의 최소연화처리시간(最小軟化處理時間)은 증자처리시(蒸煮處理時) 각각 15분, 15분 및 30분 이었다. (4) 휨가공(加工)을 위한 적정함수율(適正含水率)은 3수종(樹種) 모두 섬유포화점(鐵維飽和点) 30%에서 최대 휨가공성(加工性)을 나타냈으며 그 이상 건조(乾燥)시켜도 휨가공성(加工性)의 향상(向上)은 얻을 수 없었다. (5) 본 시험(試驗)에서 얻은 최적조건 (Table 6) 으로 휨가공(加工)을 실시한 결과(結果)소나무, 리기다소나무 및 낙엽송의 최소곡률반경(最小曲率半徑)은 증자처리시(蒸煮處理時) 각각 260mm, 240mm 및 300mm이었다.

• 신재생에너지
• /
• 제10권2호
• /
• pp.12-18
• /
• 2014

The objective of this work is to produce solid biofuel from sawdust using the HTC (Hydrothermal carbonization) process. The HTC process of feedstock involves the raw material coming into contact with high temperature and pressurized water. The HTC process could produce gaseous, liquefied and solid products, but this study focused on solid product only as an alternative to coal. In this study, sawdust used for a feedstock and its moisture content was under 5%. Water was added with the feedstock to raise moisture content to 80% and also used catalysts. The HTC process was performed at temperature range from 200 to $270^{\circ}C$ and reaction time was 15 to 120 min. Rising temperature resulted in increasing the higher heating value (HHV) of HTC product. In case of adding catalyst, HHV of solid biofuel was higher and reaction occurred at lower temperature and pressure. Also, HTC solid product had been characterized and found to be hydrophobic, increased HHV (over 40%), and pelletized easily compared to raw material.

• Journal of the Korean Wood Science and Technology
• /
• 제44권1호
• /
• pp.96-105
• /
• 2016

급속 반탄화 처리한 참나무 목분의 연료 적합성을 알아보기 위해 다양한 반탄화 시간(0, 5, 7.5, 10분)으로 제조한 반탄화 목분 시료를 10, 20, $40^{\circ}C/min$의 승온속도로 비등온 열중량분석법을 이용하여 시료의 열적 특성과 활성화 에너지를 알아보았다. 반탄화 처리시간이 증가함에 따라 시료의 열분해 시작온도($T_{onset}$)가 증가하였고, 시료 내 헤미셀룰로오스 함량은 감소하고 리그닌 함량은 증가하였으며, 열분해 반응 후의 최종 잔류물 양이 증가하는 모습을 보여주었다. 활성화 에너지는 Friedman과 Kissinger의 2가지 방법을 사용하여 추정하였으며, 각각의 결정계수 결과값은 0.9를 상회하여 계산된 활성화 에너지 값의 높은 유용성을 확인하였다. 시료의 활성화 에너지 계산 값은 반탄화 처리시간이 증가할수록 감소하는 경향이 나타났으며, 7.5분간 반탄화 처리한 시료에서 관찰된 가장 낮은 활성화 에너지 값은 급속 반탄화처리 참나무 목분의 바이오 고형연료제품으로써의 높은 적용가능성을 보여주었다.

• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.148-155
• /
• 2011

Thermal treatment techniques are used for modifying wood and wood-based materials to improve dimensional stability and hygroscopicity. This study investigated the effects of press pressure and temperature on density, vertical density profile, thickness swelling and surface hardness of eucalyptus wood boards. The experimental wood boards were prepared from Turkish River Gum ($Eucalyptus$ $camaldulensis$ Dehn.). The surface hardness value increased with increasing press pressure in the treated groups. The application of a higher pressure at the same temperature level increased the amount of swelling of wood. It means that it is not needed for application of higher pressure to enhance the dimensional stability of wood. It is expected that it is possible to produce increased hardness, dimensional stability and durability by application of hot pressing treatment. This research showed that different press pressure and temperature values should be used to improve the performance properties of eucalyptus wood so that the end-use of the wood materials could be expanded.

• Journal of the Korean Wood Science and Technology
• /
• 제19권1호
• /
• pp.22-30
• /
• 1991

This study was carried out to determine the Joint characteristic of L-type specimens. L-type specimens were made of two kinds uf solid woods(Antiaris, Sepetir) and three kinds of wood based materials(plywood, particleboard, medium density fiberboard). They were constructed with PVC anchor and screw, and were discussed with joint strength and stiffness coefficients. The obtained results were as follows: 1. Bending strength showed very high increasing rate from one to three used PVC anchor and screw but was a little rise from three to four used PVC anchor and screw in solid wood. However. in wood based materials, it was unchanged without increasing rate or slight decreased from three to four used PVC anchor and screw. 2. The stiffness coefficients, or Z-values, were in the range from $4.704\times10^{-4}$ to $1.864\times10^{-3}$(rad/kgf-cm). They showed $10^{-3}$ level in one PVC anchor and screw but $10^{-4}$ level in two, three. four PVC anchor and screw. Accordingly, they indicated flexible joints in one PVC anchor and screw and relatively stable joints in two, three. four PVC anchor and screw. 3. Measured ultimate bending moments were 258.70kgf-cm in plywood and 142.68kgf-cm in medium density fiberboard. 4. Comparing with dowel joint. the joint strength used PVC anchor screw was inferior to 8mm and 10mm dowel diameter but differ little from 6mm dowel diameter.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2007년도 제34회 KOSCO SYMPOSIUM 논문집
• /
• pp.161-167
• /
• 2007

Gasification characteristics in the fluidized bed reactor are essential for the design of a gasification furnace to optimize the operation condition. Moisture content of the solid fuel is one of the important factors to influence directly the gasification characteristics. So it is necessary to investigate the effect of moisture content of solid fuel in gasification process. Gasification characteristics are investigated with results from thermogravimetric analyser and lab-scale fluidized bed reactor for wood and RDF samples along with changing moisture contents. Additionally lab-scale fluidized bed reactor was run continuously and gas concentrations at the exit were measured. It is observed that the rate of reaction in partial oxidation condition is in between the results from the combustion environment and from the inert condition. Moisture content in a particle slows down the heating rate of a particle. So, reaction time is delayed by the moisture content. However, RDF samples that are easy to break-up doesn't show the effect of moisture content. The results of continuous operation condition shows that proper moisture content promotes gasification because steam from the particles helps gasifcation of the sold fuel.

• 한국균학회지
• /
• 제45권4호
• /
• pp.319-327
• /
• 2017

In this study, we investigated the culture conditions of four ectomycorrhizal fungi, namely, Amanita spissacea NIFoS 2719, Pisolithus arhizus NIFoS 2784, Suillus spraguei NIFoS 2848, and Xanthoconium affine NIFoS 2716, in solid and liquid culture media. In addition, we attempted to induce in vitro mycorrhization of the fungi with Pinus densiflora. Prior to liquid culture, we determined the optimal culture conditions for each species in solid media. The results revealed that all species examined are capable of growth in potato dextrose agar (PDA), malt extract agar (MEA), and modified Melin-Norkran's medium (MMN), although their preferred growth media were different. Liquid culture experiments showed that inorganic nitrogen did not enhance the mycelial growth of all four species. Therefore, we used MMN-based liquid inocula to promote the growth of ectomycorrhizal fungi in our symbiosis culture system. Mycorrhization was observed in Xanthoconium affine NIFoS 2716. Morphological analysis revealed that fungi-inoculated roots of P. densiflora form simple and dichotomous lateral roots with dense mycelia. In addition, inoculation with X. affine NIFoS 2716 promoted root and shoot developments.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.66-75
• /
• 2005

Soybean-based adhesives have recently been reconsidered as alternatives to petroleum-based adhesives due to the uncertainty of availability of petrochemical products and the increased demand for wood adhesives. This study was conducted to investigate the adhesive properties of alkaline phenolic soy (APS) resin for hybrid poplar flakeboard. The APS resin was formulated by crosslinking an alkaline soy flour hydrolyzate with lab-prepared PF resin in the soy hydrolyzate to PF resin weight ratios of 70/30, 60/40, and 50/50. The APS resins were used to fabricate homogeneous hybrid poplar flakeboards with different resin solid levels (5%, 7%, and 9%), press temperatures (175 and $200^{\circ}C$), and press times of 8 and 10 minutes. The IB, wet MOR, and dimensional stability properties of board improved with increasing press time, press temperature, and PF level in APS resins. Increasing press time can be used to offset poor IB strength associated with a 9% resin solid level and the excessive moisture content in the mat. The following conditions were concluded to meet the requirements of the CSA standard for exterior-grade flakeboard: a 50% PF level, a 5% resin content, a $200^{\circ}C$ press temperature, and an 8 minute press time.

• Journal of the Korean Wood Science and Technology
• /
• 제30권4호
• /
• pp.80-86
• /
• 2002

졸참나무 (Quercus serrata), 맹종죽 (Phyllostachys pubescens) 및 소나무 (Pinus densiflora)로부터 제조한 미정제 초액의 휘발성 성분을 고상(固相) 미량추출(solid phase microextraction; SPME)법을 이용하여 분석하였다. 이들 초액 중의 휘발성화합물 분석을 위하여 극성 (CBP 20) 및 무극성 (CBP 1) 칼람을 사용하였으며, 이로부터 총 264개의 피크를 검출하였다. 이들 성분들 중 주요 화합물은 2-butanone, acetic acid, guaiacol, phenol, 4-ethyl guaiacol, cresol류, 4-ethyl phenol, 그리고 syringol이었다. 무극성 칼람을 사용함에 의하여 7개의 성분, 즉, 1-hydroxy-2-butanone, ethisolide, furfuryl acetate, 1-(2-furanyl)-1-propane, 1,2-dimethoxybenzene, 1,2-dimethoxybenzyl alcohol, phenyl acetate를 새로이 동정할 수 있었다. 이 성분들 중 페놀류가 주성분이었으며, 휘발성 성분의 49~65%를 차지하였다. 죽초액의 경우 페놀류의 비율은 다른 두 목초액보다 낮았다. 그러나 중성화합물류 및 유기산류는 소나무 및 졸참나무로부터 제조한 목초액보다 그 비율이 더 높았다. 따라서 이들 죽초액과 목초액 간의 훈취의 차이는 목초액의 서로 다른 휘발성분의 함유량의 차이에 기인한다고 생각된다.

• 임산에너지
• /
• 제24권1호
• /
• pp.33-38
• /
• 2005

목탄의 제조과정에서 발생되는 목타르의 신용도를 찾고자 목타르를 이용한 레졸형 페놀수지접착제를 제조하여, 합판에 대한 접착력 시험을 실시하였다. 소나무타르계 접착제는 미첨가 페놀접착제와 비교했을 때, 고형분, 점도와 같은 수지의 물성은 유사하였으며, 인장 전단 접착력에서도 비내수, 내수 모두 페놀접착제에 비해 크게 떨어지지 않았다. 그러나, 참나무타르계 접착제의 경우에서는 수지물성도 페놀수지와는 다른 물성을 보였으며, 내수접착력은 페놀접착제의 접착력에 비해 절반 정도의 낮은 접착력을 보였다. 포름알데히드 방출량은 목타르의 첨가량이 많을수록 많이 방출되었다.