• Korean Journal of Metals and Materials
• /
• v.47 no.6
• /
• pp.331-337
• /
• 2009

To lower the annealing temperature and the deviation of the mechanical properties of bake hardening steels, high purity steels were investigated. The steels were characterized by treating at low recrystallization temperature. It was confirmed that the strengthening originated from the solid solution of carbon and the ferrite grain refinement by fine MnS precipitates as carbon and sulfur contents increased in high purity steels. However, it was observed that there was no more increase of strength in steels containing over 40 ppm of carbon. It was considered that the excess carbon formed either the carbon cluster or the low temperature unstable carbides which had the negligible effect on the strengthening because they were reported to be highly coherent with the matrix. The carbon cluster and unstable carbides could be transformed to the stable cementite during bake hardening treatment. MnS was not observed in the high purity steel containing 5 ppm S, resulting in very coarse recrystallized grains and good ductility. As sulfur content increased, the recrystallized grain size decreased due to the formation of the fine MnS precipitates.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.145-152
• /
• 2023

β titanium alloys containing β stabilizing elements such as V, Nb, Ta, Mo and Fe are widely used etc, due to their excellent specific strength, corrosion resistance, fatigue strength and easy formability. New metastable β titanium alloys are developed containing low-cost elements (Mo and Fe) in this study. Fe element is a strong β-stabilizer which can affect the mechanical and electrochemical properties of Ti-5Mo-xFe (x = 1, 4 wt%) alloys. These properties were analyzed in connection with microstructure and phase distribution. Ti-5Mo-4Fe alloy showed higher compression yield stress and maximum stress than Ti-5Mo-1Fe alloy due to solid-solution hardening and grain refinement hardening effect. As Fe element increased, Fe oxide formation and reduction of ${\bar{Bo}}$ (bond order) value affect the decrease of corrosion resistance. Ti-5Mo-xFe alloys were more excellent than Ti-6Al-4V ELI alloy.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.620-625
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired for car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. ill the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6N01 alloy welds. Aluminum alloy plate of 2.0mm in thickness with filler metal bar was welded by twin beam Nd:YAG laser facility (total power:5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 l/min was used. The defocusing distance is kept at 0 mm. At travel speeds of 3 to 9 m/min and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• International Journal of Korean Welding Society
• /
• v.2 no.2
• /
• pp.26-31
• /
• 2002

Considering the fuel consumption of car, a light structure of aluminum alloys is desired fer car body nowadays. However, fusion welding of aluminum alloys has some problems of reduction of joint efficiency, porosity formation and hot cracking. In the present work, investigation to improve the joint performance of laser welded joint has been carried out by addition of Cu, Ni, and Zr to A6NO 1 alloy welds. Aluminum alloy plate of 2.Omm in thickness with filler metal bar was welded by twin beam Nd: YAG laser facility (total power: 5kW). The filler metals were prepared by changing the chemical compositions for adding the elements into the weld metal. Thirteen filler metal bars were prepared and pre-placed into the base metal before welding. Ar gas shielding with a flow rate of 10 1/min was used. The defocusing distance is kept at 0 mm. At travel speeds off 3 to 9 and at laser power of 5kW (front beam 2kW rear beam 3kW), full penetration welds were obtained, whereas at travel speeds of 12 to 18 m/min and same power, partial penetration was observed. The joint efficiency of laser-welded joint was improved by the addition of Cu, Ni, and Zr due to the solid solution hardening, grain refining and precipitation hardening. The type of hardening has been further considered by metallurgical examination.

• Korean Journal of Materials Research
• /
• v.15 no.10
• /
• pp.632-638
• /
• 2005

To investigate the effect of Mo and Cu contents on tensile strength of cold drawn stainless steel 304H wires, metallographical and mechanical tests were performed for the wire specimens drawn to different drawing strains at room temperature. It was confirmed that the contents of Mo ana Cu have little influence on the tensile strength of drawn specimens, even though the strain induced martensite transformation decreased with increasing the contents of Mo and Cu. These results were explained by the strengthening of the formed martensite itself due to the solid solution effect of interstitial solutes, carbon and nitrogen. The contents of these elements were slightly higher in the specimens containing additionally added Mo and Cu.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.2 s.233
• /
• pp.214-219
• /
• 2005

To investigate the change of internal stress and mobile dislocation density in the creep, stress relaxation test was examined from each strain range. Mobile dislocation density increased until it reached minimum creep rate but after that, it decreased. Internal stress did not change until it reached minimum creep rate but after that, it decreased. The stress relaxation rate is fast and approached zero later 1.5 seconds, which were begun in the stress relaxation. When the applied stress is large, the internal stress is large. It is cleared that dislocations glide viscously which N passes by cutting Cr atom rather than typical viscosity movement by the evaluation of mobility of dislocation in STS310J1TB.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2009.12a
• /
• pp.72-73
• /
• 2009

First-principles calculations were carried out to investigate the effects of Al impurities on bcc Fe magnetism by considering SOC. No significant solid solution hardening effect was found. Albeit the effects of the SOC by Al on spin magnetic moments were minor, there are sizeable orbital magnetic effects. It is concluded that the orbital magnetism due to the Al impurity is strongly related with the impurity screening of the system as seen in Si impurity case [3], but the effects of Al impurity is stronger than those of Si impurity in terms of orbital magnetism.

• Journal of Korea Foundry Society
• /
• v.12 no.2
• /
• pp.139-148
• /
• 1992

The mechanical properties of Ti-Al intermetallic compounds which contain Mn, Zr, or Cr as the third element have been evaluated by means of hardness and compression tests. Microstructures have also been examined using an optical microscope. The cast structures of Ti-Al alloys are coarsened and the lamellar volume fraction is increased by the additions of Mn or V, but the cast structures are refined by the addition of Zr. Hardness tests of room temperature and compression tests at $600^{\circ}C$ showed that the mechanical properties of Ti-Al alloys were mainly dependent on the volume fraction of the ${\alpha}_2$ phase, grain size and solid solution hardening. However according to the compression test at $1000^{\circ}C$, the yield strength of Ti-Al alloys decreased with an increase in Mn or Cr content, but increased with an increase in the Zr content.

• Journal of Korea Foundry Society
• /
• v.11 no.6
• /
• pp.482-490
• /
• 1991

This study presents the wear characteristics of Ti alloys (Pure Ti, Ti-6Al-4V, Ti-5Al-2.5Sn) fabricated by centrifugal precision casting in an Ohara dental titanium casting machine. It was found that the hardness of the surface region is higher than that of the interior region. It is considered that the oxygen adsorption in the surface region during casting, leads to the interstitial solid solution hardening. Wear resistance incerases in the order of pure Ti, Ti-6Al-4V, Ti-5Al-2.5Sn alloys. The interior hardness value increases in the same order. The specific wear rate increases with applied load and increases monotonously with sliding speed. The Fe transfer from the counterpart material was observed on the worn surface of the Ti-5Al-2.5Sn alloy. Oxidative wear occurs at low sliding speeds and mechanical fracture wear occurs at high sliding speeds.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.296-301
• /
• 2004

By the purpose to investigate the change of internal stress and mobile dislocation density in creep, the stress relaxation test is carried out in the condition of each strain. Mobile dislocation density increased until it reached minimum creep rate and after that, it decreased and internal stress didn't have the change approximately until it reached minimum creep rate and after that, it decreased. The stress relaxation rate is fast and approached zero after 1.5 seconds after the beginning of the stress relaxation. And the larger the applied stress is, the larger the internal stress is. By the evaluation of mobility of dislocation, the dislocations glide viscously in STS31OJlTB but it is the dislocations glide viscously which N passes by cutting Cr atom rather than typical viscosity movement after calculating mobility of dislocation.