Post-harvest treatment for barley production requires many steps including drying, cleaning, and packing, and these steps be needed many labor input. Rice processing complex (RPC) is useful for post harvest management system in rice production. However, it is rare to be used for barley production. This study was conducted to explore the variations of quality and labor saving between conventional method and bulk-management system in post-harvest using RPC. The sorting rate was not different between manual method and bulk management. The hardness of non-polished grain was ranged 10,175-10,329 g/$3.14mm^2$, and that for non-polished grain was higher than that for polished grain, but there was not different between drying method. There was not be showed the hunter's value such as L, a and b according to drying method. Cooking characters such as water absorption ratio, swelling ratio, and water soluble extracts by circulated or continued dryer was higher than manual drying using solar heat. Labor input per ha for each cultivation process in bulk-management of barley using rice processing complex was 21 hours, compared to 46 hr/ha in the conventional method, labor input was greatly saved by up to 54.3% in the post-harvest bulk management system.
Two types of fiat-plate collector were designed and constructed for utilizing the solar energy as heating source of red pepper drying. It was performed to investigate the basic factors on using the collectors and the drying effect on various types of red pepper, and the results obtained are summarized as follows. 1. The optimum tilted angles of the collector in Daejeon area were ${\phi}-15^{\circ}$ in summer season and ${\phi}+15^{\circ}$ in winter season when it was adjusted two times per a year: 2. In the conditions during experiment period, average atmospheric temperature and relative humidity were $25.6^{\circ}C$ and 52.6%, respectively, and $42.0^{\circ}C$, 74.2% in the control chamber. The temperature in the drying chamber connected to the water heater was the highest but relative humidity in the chamber connected to the air heater was the lowest among the chambers. 3. The drying velocity of whole red pepper in the chamber connected to the water heater was the fastest as 2.3 times as compared to the whole type on the mat drying followed by air heater and control in decreasing order. The horizontally cut red pepper in the chamber connected to the water heater was dried exceedingly fast among twelve plots. 4. The content of capsaicine as pungent principle and of capsanthine as red pigment in the red pepper were reduced during drying but there were no differences significantly on the drying method, and it could not affect much on the quality of dried product.
Park, Hyo-Won;Oh, Sung-Il;Cho, Mun-Gyeong;Kim, Chul-Woo;Lee, Uk
Journal of Korean Society of Forest Science
/
v.107
no.4
/
pp.422-427
/
2018
This study was performed to determine quality characteristics of solar-dried persimmon for each cultivar. The physical and sensory characteristics of 4 cultivars of solar-dried persimmons (Gojongsi, Godongsi, Sangjudungsi, Koshuhyakume) were investigated. As a result, yield rate and firmness was highest in Koshuhyakume (29.5%, 9.62 N). Meanwhile, the soluble solid content (SSC) was the highest in Gojongsi ($27.3^{\circ}Brix$) and it has a significant difference between 4 cultivars (p<0.05). The water activity was range from 0.784 to 0.819 and Gojongsi (0.784) was significantly lower than others. The water contents value was the highest in Koshuhyakume (37.51%), while Sangjudungsi (35.32%) was the lowest. In case of Hunter's value, 'L', 'a' and 'b' were the highest in Sangjudungsi (34.56, 9.24, 17.07), whereas Koshuhyakume (29.17, 5.68, 13.59) has generally low value. In sensory evaluation, overall acceptability was the highest in Gojongsi and Godongsi (5.16), while Koshuhyakume (3.95) was the lowest. The results showed that the quality characteristics of dried persimmon manufactured by solar drying method have distinct difference according to cultivars.
A 2.5 ton scale of solar energy concentration blast-grain circulation dryer (SECD) was developed in order to shorten the drying time without damaged paddy. Comparative experiments were carried out on performance, drying efficiency, consistency in moisture content, milling recovery, grade of milled rice, and energy requirement and cost against all that of in-bin drying and storage (IBDS) method. The experiments were performed using mixture of several rice varieties of Tongil type(Japonica-Indica breeding type) under the autumn weather in Korea. The circulating air temperature inside SECD was $4{\sim}5^{\circ}C$ higher than that of IBDS. The moisture content of the paddy during the drying period in SECD was uniform while substantially varied in upper, middle or bottom layer in IBDS. By SECD, 24% initial moisture content of paddy was reduced to 15% after only 3 days of drying as compared to 14 days at IBDS. The percentage of cracked kernels in upper, middle and bottom layers in IBDS was 6, 6 and 12%, respectively, whereas 7% in all layers in SECD. Both types of dryers did not significantly affect the milling recovery of dried paddy and grade of milled rice. Energy requirement of SECD(28.8Kw/2.5ton) for paddy drying was much less than that of IBDS(108Kw/2.5ton).
Journal of the Korea Academia-Industrial cooperation Society
/
v.21
no.9
/
pp.128-133
/
2020
This study was conducted to demonstrate the manufacturing process for producing high-quality solar salt. The design criteria of the manufacturing process, which was studied in a previous study, was applied to an actual manufacturing system to evaluate its performance. The design factors applied were the drying air temperature and the temperature of the washing water. They were 100℃ or less and 10℃ or less, respectively. Two standards were applied to the process performance evaluation. Standard (I) was the international food standard for solar salt, and standard (II) was the quality standard for high-quality solar salt production. The main quality evaluation items were the moisture content and salinity, and the color characteristics were also measured (p<0.05). The manufacturing process of solar salt consisted of five steps, and the quality change was measured for each step. The measured quality was appropriate to the standard (I) from the third-step process. In addition, the quality of the high-quality solar salt was suitable for the standard (II) from the fourth-step process. Therefore, the performance of the proposed solar salt production process met international standards. The improvements in the production of high-quality solar salt will improve international competitiveness in the future.
본 연구는 현재 국내 농촌에서 문제시되고 있는 벼의 건조와 저장방법을 개선하기위한 한 가지 방법으로써 Grain bin의 이용에 따른 기술적인 적용가능성을 구명하는데 있었으며 건조열원으로서는 상온공기와 Solar collector 에 의한 보충가열공기를 사용하였다. 건조시험에서는 벼의 건조속도, 층별함수율의 변화, 동력소모량, 도청수율 등을 측정 비교하였으며 건조가 완료된 후에는 저장시험도 아울러 실시하였다. 본 시험을 통하여 얻은 결과는 다음과 같다. 1. 본시험에 사용된 Solar Collector 는 집열면적이 $27.7m^2M$의 Flat-plate 형식이며 내부에 태양열의 저장모체로서 약 $7m^2M$의 검은 돌을 사용하였다. Collector 의 효율은 35%이었으며 Collector를 통과하여 Bin으로 들어가는 공기의 온도는 외기온에 비하여 주간에는 약 $4^\circ C$, 야간에는 약 $8^\circ C$, 정도 상승된 것으로 나타났다. 2. 상온공기와 Collector를 이용한 건조험결과 안전저장함수율에 도달하는 데 약 7일과 약 5일이 소요되었다. 3. 태양열 건조는 상온통풍건조에 비하여 곡물층간의 함수율차이가 약간 크게 나타났으나 건조속도가 빠를뿐만 아니라 동력소모량도 적은 것으로 분석되었다. 4. 건조시험이 완료된 직후 이차에 걸쳐 Bin 내에서 저장시험을 실시한 결과 저장기간중 벼의 안전보전이 가능했으며 평균함수율이 12.0~14.5%범위에서 유지되었다.
Journal of the Korea Academia-Industrial cooperation Society
/
v.21
no.8
/
pp.298-303
/
2020
This study examined the washing conditions for high-quality solar salt. The salinity of the washing water was set to 5 % to prevent yield loss, and the temperatures of the washing water were 5, 10, 17.5, and 20 ℃. After washing the solar salt, the moisture content, salinity, insoluble matter, and sandy powder were measured from the solar salt. In addition, the color properties, L*[lightness], a*[redness], b*[yellowness], and yield were measured. The moisture content of the salt showed a tendency to increase when the temperature of the washing water was above 10 ℃, and the salinity and yield tended to decrease as the temperature of the washing water was high. The amount of insoluble matter decreased with decreasing temperature of the washing water. In the case of sandy powder, the highest value was 0.67 % at a washing water temperature of 5 ℃, and the value was 0.57 % under the other temperature conditions. Regarding the color properties, the b* [yellowness] of the color of the solar salt increased when the washing water temperature was high. This appeared to decrease the appearance quality. According to the above results, a washing water temperature above 10 ℃ was appropriate. The development of design factors of a high-quality solar salt production system is expected with experiments to define the drying conditions after the washing process.
Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
/
2004.05a
/
pp.183-189
/
2004
Deep ocean water is located in the sea deeper than 200m. At such depth the solar light does not reach, photosynthesis is not performed and nutrition salt is not consumed. Therefore, campared with surface water, Deep Sea Water contains more nutrition salt, such as nitrogen and phosphor. Moreover, it has the good balance of minerals. This Research is primary attempt for apply deep sea water to food industry. New type of mineral salt manufacturing system was developed and high levels of Ca, K, Mg detected from the salt analysis.
Proceedings of the Materials Research Society of Korea Conference
/
2011.05a
/
pp.1.2-1.2
/
2011
With recent advances in materials and products, materials processing experiences new challenges. More particles and polymers in material side and thinner and faster deformations in processing side. It happens in most emergying industries such as manufacturing of batteries, solar cells, multi-layer chips, displays, printed electronics, to list a few. In most cases, they are manufactured by coating or printing process, which is defined as a process in which gas is replaced by liquid on a substrate. In this sense, casting, inkjet printing, and roll-to-roll printing are all included. The printing process consists of three unit processes. As the materials used in the above mentioned applications typically contain a large amount of particles with polymers and solvents, they continuously change microstructures during preparation, flow, and even drying. However, little is known about the flow characteristics of such complex fluids and less is known about how to design and control the process. Therefore, for better control of the process and for better quality of the product, we need to understand the flow characteristics of these complex fluids under extremely fast flow environment.
The flat-plate and tubular soar collectors were designed and constructed for drying the rough rice, and the performance of the collectors and drying effect were investigated when rough rice was packed in grain bin connected to collectors. Average-monthly radiation on a horizontal surface based on bright sunshine in Daejeon area during 1978 was the highest as $16,814\;KJ/m^2{\cdot}day$ in May and the lowest as $4,254\;KJ/m^2{\cdot}day$ in December, and significane was not recognized between the calculated and recorded values. The thermal effciency of collectors were increased as radiation increased during drying period and the average thermal effciency of flat-plate and tubular collectors in 11 to 12 o'clock a.m were 28.12 and 16.75%, respectively. The average inlet temperature of grain bin at 12 o'clock was shown as 20.02 at control 40.5 at grain bin connected to tubular collector and $55.1^{\circ}C$ at grain bin connected to flat-plate collector. In 25 cm rough rice depth in grain bin, tim taken for drying from initial moisture content at 27.4 to decrease upto 17.0% (14.5 % on wet basis) were 32 in control, 18 in grain bin connected to tubular collector and 11 hrs to flat-plate collector, and grain depth influenced drying rate remarkably. In the view point of drying characteristics, drying pattern showed initially falling-rate to constant-rate period finally.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.