• Journal of the Korean GEO-environmental Society
• /
• v.24 no.5
• /
• pp.21-28
• /
• 2023

In this paper, an experimental study was conducted to present the properties of rapid hardening composite mat, and a numerical analysis was carried out to analyze the slope protection effect of the mats based on ground conditions, rainfall, slope gradient and soil height. As a result, the application of rapid hardening composite mat increased the slope safety factor in all conditions, and the increase rate of safety factor showed an average of 40% increase both in dry and rainy seasons. Through these research findings, the protective effect of the rapid hardening composite mat on sloping surfaces has been proven, and it is suggested that the rapid hardening composite mat is suitable for application in areas where slope failure or collapse is expected.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.8
• /
• pp.117-127
• /
• 2007

Slope stability analysis is a geotechnical engineering problem characterized by many sources of uncertainty. Some of them are connected to the uncertainties of soil properties involved in the analysis. In this paper, a numerical procedure for integrating commercial finite difference method into probabilistic analysis of slope stability is presented. Since the limit-state function cannot be expressed in an explicit form, the ANN-based response surface method is adopted to approximate the limit-state function and the first-, second-order reliability method and the Monte Carlo simulation technique are used to calculate the probability of failure. Probabilistic stability assessments for a hypothetical two-layer slope and the Sugar Creek embankment were performed to verify the application potential to the slope stability problems. The examples show the successful implementation and the possibility of the extension of the proposed procedure to the variety of geotechnical engineering problems.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.6
• /
• pp.21-28
• /
• 2010

Decomposed granite soil is the most common type of soils. The measurement of the stress-strain-strength behavior of anisotropic decomposed granite soils is very important for the deformation and stability analysis of slopes, retaining walls, excavations. A series of unsaturated-drained triaxial compression tests were performed to know unsaturated strength properties. The sample had three different angles of the axial (major principal) direction to the sedimentation plane (compaction plane): 0, 45 and 90 degrees. The compression strain of specimens subjected to an isotropic compression was strongly influenced by the sedimentation angle. In addition, the time dependence was independent of the sedimentation angle in relation to the deformation behavior during the secondary compression process. The effect of the sedimentation angle on the triaxial compression strength and deformation was clearly shown with low confining stress. The effect of the sedimentation angle on the compressive strength and deformation was more evident in saturated specimens. A new method of predicting the shear strength of unsaturated decomposed granite soils, considering compaction angles, was proposed.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.85-85
• /
• 2020

South Korea experiences few large scale erosion and sedimentation problems, however, there are numerous local sedimentation problems. A reliable and consistent approach to modelling and management for sediment processes are desirable in the country. In this study, field measurements of sediment concentration from 34 alluvial river basins in South Korea were used with the Modified Einstein Procedure (MEP) to determine the total sediment load at the sampling locations. And then the Flow Duration-Sediment Rating Curve (FD-SRC) method was used to estimate the specific degradation for all gauging stations. The specific degradation of most rivers were found to be typically 50-300 tons/㎢·yr. A model tree data mining technique was applied to develop a model for the specific degradation based on various watershed characteristics of each watershed from GIS analysis. The meaningful parameters are: 1) elevation at the middle relative area of the hypsometric curve [m], 2) percentage of wetland and water [%], 3) percentage of urbanized area [%], and 4) Main stream length [km]. The Root Mean Square Error (RMSE) of existing models is in excess of 1,250 tons/㎢·yr and the RMSE of the proposed model with 6 additional validations decreased to 65 tons/㎢·yr. Erosion loss maps from the Revised Universal Soil Loss Equation (RUSLE), satellite images, and aerial photographs were used to delineate the geospatial features affecting erosion and sedimentation. The results of the geospatial analysis clearly shows that the high risk erosion area (hill slopes and construction sites at urbanized area) and sedimentation features (wetlands and agricultural reservoirs). The result of physiographical analysis also indicates that the watershed morphometric characteristic well explain the sediment transport. Sustainable management with the data mining methodologies and geospatial analysis could be helpful to solve various erosion and sedimentation problems under different conditions.

• Korean Journal of Ecology and Environment
• /
• v.49 no.1
• /
• pp.31-41
• /
• 2016

Deutzia paniculata is an endemic species to the Korean Peninsula. Despite of importance for conservation, the population structure and habitat characteristics of D. paniculata have not been determined yet. We analyzed the ecological characteristics of the species based on the literature review and field survey. Field survey was conducted on May to October 2014 during which 11 quadrats of size $15{\times}15m$ were studied in six regions. Each of the quadrats were further divided into $5{\times}5m$ small quadrats and population characteristics were recorded. The population and habitat characteristics were analyzed, including species abundance (density and coverage), demographic attributes (flowering rates and fruiting plants), vegetation (structure, species composition), light availability (transmitted light and canopy openness) and soil characteristics (temperature and humidity). We found that D. paniculata mainly distributed in Gyeongsangdo (including Taebaek in Gangwondo) along a broad elevational range of 290~959 m (mean: 493 m) above sea level. In preferred habitat the species grows within the slope range of $7^{\circ}$ and $35^{\circ}$ with the average of $16^{\circ}$. D. paniculata was generally distributed on talus deposits and low adjacent slopes. The average number of individual plants per small quadrat was 12.5 with the mean density $0.5stems\;m^{-2}$. The vegetative reproduction was frequent in D. paniculata and mean flowering rate was as low as 15%. Altogether 138 taxa were found in whole observation area with the dominant tree species mainly spring ephemerals, such as Cornus controversa (importance value: 25.5%) and Fraxinus rhynchophylla (importance value: 15.8%). Although, C. controversa usually grows on steep slopes and F. rhynchophylla mostly distributed at high-altitudes, however, both species distributed in disturbed environments and among talus deposits. Thus based on our results, we concluded that D. paniculata is a disturbance-prone species, primarily existing in habitats subjected to natural disturbances, such as floods. The species occurs less at anthropogenically disturbed sites, thus there is no apparent threat to the populations and habitat of D. paniculata.

• Korean Journal of Soil Science and Fertilizer
• /
• v.19 no.2
• /
• pp.99-105
• /
• 1986

This study was carried out to compare the soil profile development indices of Sinjeong series according to the distribution areas in Yeongnam district. The results obtained were as follows; 1. The soils studied were belong to fine loamy family of hilly residual soils derived from conglomerate. These soils were well drained and dominantly had 30-60% slopes, and used for forest. 2. The surfaces were typified by brownish red (5YR) or brownish yellow (10YR) loam, subsoils were clay loam of reddish brown (5YR) or reddish yellow (7.5YR) and the substrata were in dark reddish brown (5YR) or pink (7.5YR) sandy loam. 3. The indices of horizon development of the soils studied were from 0.18 to 0.38 and the index in illuvial horizons with clay films were over 0.36, that were higher than the others. The profile development indices were similar to each other ranging from 30.18 to 35.93. 4. Positive correlations were observed among horizon development indices and normalized values of structure, texture and consistences, but the relationship between profile development indices and consistences were not the same. 5. The amount of clay minerals formed in the soil horizons per 100g of parent materials were 1.1-1.6g and the rates of the clay leached were around 4.4-5.9%. 6. The sphericity and roundness of the gravels contained in the soils studied were 0.741 and 0.715, respectively. These similarity of "well rounded" gravels certify that the parent rocks were formed under similar environments.

• Journal of Environmental Policy
• /
• v.11 no.3
• /
• pp.25-47
• /
• 2012

This research is to suggest an ecological management methods by classification of biotope type and its mapping for Tricholoma matsutake. The target area was construction site of the East Hongchun - Yangyang Highway (Yangyang section) where massive production of Tricholoma matsutakes is in place. Specifically, the 700 m long range of area around the road route, Yangyang section, which is over a total area of $19,79km^2$. The flow of this research was as follows: first studied were the characteristics of the Yangyang Tricholoma matsutakes; second, reviews on previous studies on Tricholoma matsutakes; third, the formulation of standards and processes of biotope type considering Tricholoma matsutake production; and fourth, mapping of biotope considering the production area of Tricholoma matsutake. In 24.77% of the region, slope angle measured $30{\sim}40^{\circ}C$, which is suitable for Tricholoma matsutake production. Also, 17.44% of the region had southward vegetation structures, and as for the Pinus densiflora; 26.00% had average receipts; the tree ages was $38{\pm}8.34$ years; and the average density of canopy layer was $9.55{\pm}4.89/100m^2$. The soil acidity (pH) values of 5.0 to 5.6(47.96%) > 5.6 to 7.0(42.90%) > 4.0 to 5.0(9.14%) were slightly high for Tricholoma matsutake growth; but 57.10% of the area had a soil pH of 4.0-5.6. The organic horizon (A0 layer) was $3.39{\pm}2.14cm$, and the mean depths were 4-6cm(78.03%) > 0-2cm(18.10%) > 2-4cm(3.87%). Based on the results of previous studies and field researches on the presence of vegetation (the pine dominance ratio), the topographic structure (the terrain characteristics and slopes), the receipt, the soil structure (the soil acidity and the organic layers interposed between the depths), and the vegetation density, six clusters based on the identified types of biotopes are produced in this paper. Area of distribution according to the type of biotope was Tricholoma matsutake of the potential-production (II) biotope (32.86%) > Tricholoma matsutake of the inadequate-production biotope (22.17%) > Tricholoma matsutake of the adequate (II)-production biotope (17.79%) > Tricholoma matsutake of the adequate (I)-production biotope (14.86%) > Tricholoma matsutake of the potential-production (I) biotope (9.77%) > Tricholoma matsutake of the produced biotope (2.55%).

• Journal of Korean Society of Forest Science
• /
• v.111 no.1
• /
• pp.115-124
• /
• 2022

This study was conducted to obtain basic data that could help prevent damage caused by slow-moving landslides (land-creep). Specifically, the geological, topographic, and physical characteristics of land-creep were analyzed in Jiphyeon-myeon, Jinju-si. The first and second analyzed land-creeps occurred in 1982 and 2019, respectively. The area damaged in the second land-creep was about 11.5-fold larger than that damaged in the first land-creep. The dominant constituent rock in the land-creep area was sedimentary rock, which seems to be weakly resistant to weathering. The areas that collapsed due to land-creep were related to the presence of separated rocks between the bedding plane in the estimated activity surface over the slope direction and the vertically developed joint surface. Thus, surface water and soil debris were introduced through the gaps of separated rocks. Additionally, the areas collapsed due to the combination of the bedding plane and joint surface shale and sandstone showed an onion structure of weathered outcrop from the edge to inner part caused by weathering from ground water. Consequently, core stones were formed. The study area was a typical area of land-creep in a mountain caused by ground water. Land-creep was classified into convex areas of colluvial land-creep. The landslide-risk rating in the study area was classified into three and five classes. The flow of ground water moved to the northeast and coincided with the direction of the collapse. Soil bulk density in the collapsed area was lower than that in ridge area, which was rarely affected by land-creep. Thus, soil bulk density was affected by the soil disturbance in the collapsed area.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.1
• /
• pp.37-47
• /
• 2014

Unsaturated hydraulic conductivity (HC) is integrated theoretically from soil water retention curves (SWRC) by Mualem capillary model, but the prediction of HC is extremely sensitive to small variation of matric suction near saturation. Near saturation, the Mualem HC based on smooth SWRC decreases abruptly and has problems in the reliability of hydraulic behavior and the stability of numerical solutions. To improve van Genuchten-Mualem (VGM) HC, the van Genuchten SWRC model is modified within range of low matric suction (arbitrary air entry pressure). At an arbitrary air entry pressure, the VG SWRC is linearized in log scale until full saturation. The modified VG SWRC does not affect the fit of actual retention behavior and either the parameters of original VG SWRC fit. Using the modified VG SWRC, the VGM HC is modified to integrate for each interval decomposed by arbitrary air entry pressure. An analytical solution on modified VGM HC is proposed each interval, to protect the rapid change in HC near saturation. For silty soils, VGM models of HC function underestimate the unsaturated permeability characteristics and especially show rapid reduction near saturation. The modified VGM model predicts more accurate HC functions for Korean weathered soils. Furthermore, near saturation, the saturated HC is conserved by the modified VGM model. After 2-D infiltration analysis of an actual slope, the hydraulic behaviors are compared for VGM and the modified models. The prediction by the proposed model conserved the convergence of solutions on various rainfall conditions. However, the solution by VGM model did not converge since the conductivity near saturation reduced abruptly for heavy rainfall condition. Using VGM model, the factor of safety is overestimated in both initial and final stage during heavy rainfall. Stability analysis based on infiltration analysis could simulate the actual slope failure by the proposed model on HC.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.12
• /
• pp.135-145
• /
• 2019

The slope collapse can be classified into internal and external factors. Internal factors are engineering factors inherent in the formation of slopes such as soil depth, slope angle, shear strength of soil, and external factors are external loading such as earthquakes. The external factor for earthquake can be expressed by various values such as peak ground acceleration (PGA), peak ground velocity (PGV), Arias coefficient (I), natural period (T_p), and spectral acceleration (S_aT=1.0). Specially, PGA is the most typical value that defines the magnitude of the ground motion of an earthquake. However, it is not enough to consider the displacement in the slope which depends on the duration of the earthquake even if the vibration has the same peak ground acceleration. In this study, numerical analysis of two-dimensional plane strain conditions was performed on engineered block, and slope responses due to seismic motion of scaling PGA to 0.2 g various event scenarios was analyzed. As a result, the response of slope is different depending on the presence or absence of sliding block; it is shown that slope response depend on the seismic wave triggering sliding block than the input motion factors.