• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.121-128
• /
• 2004

A constiutive model was proposed in order to model dilatancy under $K_0$ conditions. The model includes an anisotropic hardening rule with bounding surface and hypothetical peak stress ratio and dilatancy function which are dependent on a state parameter. The triaxial stress-strain relationship under $K_0$ conditions was calculated reasonably by the proposed model. In particular the model could consistently predict dilatancy in volume change, softening with peak strength and small strain behavior.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.7
• /
• pp.5-15
• /
• 2014

Abandoned mine deposits are exposed to various physico-chemical geo-environmental hazards and disasters, such as acid mine drainage, water contamination, erosion, and landslides. This paper presents the ring shear characteristics of waste materials. The ring shear box with a rotatable O-ring was used in this study. Three tests were performed: (i) Shear stress-time relationship for given normal stress and shear speed, (ii) shear stress as a function of shear speed, and (iii) shear stress as a function of normal stress. For a given normal stress (50 kPa) and speed (0.1 mm/sec), the materials tested exhibit a strain softening behavior, regardless of drainage condition. The peak and residual shear stresses were determined for each normal stress and shear speed. The shear stress was measured when shear speed is equal to 0.01, 0.1, 1, 10, 50, 100 mm/sec or when normal stress is equal to 20, 40, 60, 80, 100, 150 kPa. From the test results, we found that the shear stress increases with increasing shear speed. The shear stress also increases with increasing normal stress. However, different types of shearing mode were observed in drained and undrained conditions. Under drained condition, particle crushing was observed from the shearing zone to the bottom of lower ring. Under undrained condition, particle crushing was observed only at the shearing zone, which has approximately 1 cm thick. It means that a significant high shear speed under undrained condition can result in increased landslide hazard.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.627-631
• /
• 2005

In this study, low fatigue behavior of laser welded sheet metal were investigated. Before welding, the cross section of butt joint was prepared only by fine shearing without milling process. Specimens were same sheet metal and welding condition that using automobile manufacturing company at present. Butt joint of cold rolled sheet metal was welded by $CO_2$ laser. It is used that welding condition such as laser welding speed was 5.5m/sec and laser output power was 5kW for 0.8mm and 1.2mm sheet metal. The laser weldments were machined same or different thickness and same or different material. In order to mechanical properties of around welding zone, hardness test was performed. Hardness of welding bead is about 2 times greater than base material. We performed the low cycle fatigue tests for obtaining fatigue properties about thickness and the weld line direction of specimen. The results of strain controlled low cycle fatigue test indicate that all specimens occur cyclic softening, as indicated by the decrease in stress to reach a prescribed strain.

• The Journal of Korean Academy of Prosthodontics
• /
• v.19 no.1
• /
• pp.17-27
• /
• 1981

This study was conducted to determine the chemical composition and the mechanical properties of four commercially available low gold-based crown and bridge alloy produced in Korea. Four dental casting gold-silver-palladium alloys, i.e., A, B, C and D (code of alloys) were selected for the evaluation of chemical composition, ultimate tensile strength, elongation. values and Vickers hardness. The chemical composition of test specimens was analyzed by both emission spectrography and wet gravitation method with a 1.5gm of low gold ingot. The tensile properties and Vickers hardness was determined with cast specimens treated in following three conditions; as-cast, softening heat treatment and hardening heat treatment. The tensile testing bars were cast in accordance with the model designed by Gettleman and Harrison (1969) which was modified from the A. D. A. Specification No. 14 for dental chromium-cobalt casting alloy. Nine tensile test specimens were made from a split silicone mold for each of the test alloys to the size of 2.5mm in diameter and a gauge length of 10mm. All four alloys were handled in accordance with conventional methods used in Type III gold alloys. Ultimate tensile strength and elongation were measured on an Instron Universal Tensile Testing Machine (Model 1125, Japan) operated at a crosshead rate of 0.1cm/min. Elongation values were measured using Digital Measuring Microscope (MS-152, FUSOH, Japan). Vickers hardness was determined with a Vickers Hardness Tester (Model VKH-l, Japan) at a 1.0kg load on a mounted tensile test specimen. The following results were obtained from this study; 1. All tested alloys were composed of Au, Ag, Pd, Cu, Zn and Fe in common. The composition rate of gold for all four alloys was found in the range of $42{\sim}47$ weight % as shown below. Alloy A; Au 45%, Ag 40.2%, Pd 5.76%, others 9.04%. Alloy B; Au 47.1%, Ag 29.03%, Pd 6.98%, others 16.92%. Alloy C; Au 45%, .Ag 26.9%, Pd 6.83%, others 21.07%. Alloy D; Au 41.8%, Ag 34.4%, Pd 6.95%, others 16.85%. 3. The ultimate tensile strength of the four alloys was in the range of $31{\sim}82kg/mm^2$. The test results were shown in the below order from the highest value; As-cast condition; D, B, C, A. Softening heat treament; B, C, D, A. Hardening heat treatment; D, B, C, A. 4. The test :results of the elongation rate for each alloy were in the range of $0.5{\sim}18%$. The test results were shown in the below order from the highest value; As-cast condition; A, D, B, C. Softening heat treatment; A, C, D, B. Hardening heat treatment; C, D, B, A. 5. Vickers hardness for each of the four alloys was in the range of $120{\sim}230$. The test results were shown in the below order from the highest value; As-cast condition; C, B, D, A Softening heat treatment; D, B, C, A. Hardening heat treatment; D, A, C, B. 6. There were no differences in the physical properties between as-cast condition and softening heat treatment.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.4
• /
• pp.24-33
• /
• 1991

The effects of thermomechanical treatments on microstructure and fatigue properties of 7050 Al alloy were investigated. The precipitation kinetics changed to a faster rate due to cold deformation employed in this special TAHA thermomechanical treatments including pre-aging, plastic deformation and two step final-aging. The G.P. zones in the under-aged condition were cut by dislocations and dissolved during the plastic deformation. During the low cycle fatigue, the T6' condition showed cyclic hardening behavior whereas the TMT5, TMT27 and T76 conditions showed cyclic softening at above 0.7% total strain amplitudes. The ${\Delta}K_{th}$ value of TMT27 was improved more than two times, compared with that of T76 condition. The T6' with small shearable precipitates resulted in the markedly high ${\Delta}K_{th}$ value. This is thought to be resulted from dislocation reversibility and roughness-induced crack closure due to planarity of slip.

• Korean Journal of Food Science and Technology
• /
• v.29 no.4
• /
• pp.758-763
• /
• 1997

Fresh jujubes (Zizyphus jujuba Miller) of whitish green and red ripe maturities were stored at 5 different temperatures, and quality changes through the storage were measured to find an optimal storage condition. Respiration rates and their temperature dependences for both maturities were not different from each other, which suggested non-climacteric pattern of postharvest respiration. Red ripe fruits showed heavier weight and higher content in soluble solid and ascrobic acid compared with whitish green mature fruits. Through the storage of jujubes in perforated packages tissue softening and decay were main visual quality deteriorations with the former preceding the latter. The whitish green mature jujubes showed slower rate of quality changes in softening and decay than red ripe ones, and are thus more suitable for long term storage. In the storage, the whitish green fruits changed into red color, and showed increase in soluble solid and decrease in acidity and ascorbic acid content. Storing the jujubes at $-2^{\circ}C$ resulted in symptoms of chilling injury, and storing at higher temperatures above $0^{\circ}C$ accelerated the decay and softening. $0^{\circ}C$ was found to be optimal temperature for long term storage, where jujube had the lowest rate of quality changes without chilling injury. Even at optimal temperature of $0^{\circ}C$, however, storage life retaining freshness was only around 40 days which is not enough.

• Culinary science and hospitality research
• /
• v.20 no.2
• /
• pp.54-64
• /
• 2014

In order to enhance the firmness of retorted onion, long time, low temperature blanching(LTLT) in calcium solution was conducted. Pre-heating onion in calcium solution significantly improved its texture after high temperature sterilization as compared to conventional blanching alone. The improvement of the firmness by the LTLT blanching is related to the formation of strongly cross-linkages between carboxyl groups and divalent cations($Ca^{2+}$) by the action of pectin methy-lesterase(PME) in onion. A maximum firmness of retorted onion was obtained at the condition of pre-heating at $70^{\circ}C$ for 120min in 0.5%calcium solution. This result supports that the activity of PME and the content of bonded calcium in onion were highest at $70^{\circ}C$. Additionally, the reaction of alkali calcium with various divalent cations such as $Mg^{2+}$ provided a function to hydrolyze pectin molecules, resulting in firmer retorted onion in various calcium agents. Further investigation should be carried out to determine the optimal condition for prevention of tissue softening of various retorted vegetables.

• The Journal of Engineering Geology
• /
• v.26 no.3
• /
• pp.307-314
• /
• 2016

Shear characteristics of soils can be investigated using various types of shear stress measuring apparatus. Ring shear tests are often applied for examining the residual shear strength under the unlimited deformation. This paper presents drainage-consolidation-shear velocity dependent undrained shear strengths measured in terms of water leakage. A series of ring shear tests were performed under the constant normal stress (50 kPa) and controled shear velocity ranging from 0.01~1 mm/sec under the undrained condition. As a result, undrained shear strengths are dependent on shear velocity. It exhibits that straining hardening behavior is observed for the shear velocity lower than 0.1 mm/sec; however, the strain softening behavior is observed for the shear velocity higher than 0.1 mm/sec. Water leakage can cause the increase in shear stress irrespective of shear velocity. Shear stress increases with increasing amount of water leakage. It is due to the fact that the small grains and water flow out through the rubble edge in the ring shear box. Repetitive saturation and consolidation processes may minimize the error.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.2
• /
• pp.92-98
• /
• 2011

The influence of the cooling condition after solution treatment on the high temperature fatigue resistance of 23Cr-26Ni heat resistant steel was investigated. Two different cooling conditions were applied to the steel after solution treatment at $1200^{\circ}C$ for 3 hours. One specimen was water quenched immediately after the solution treatment. The other one was furnace cooled at a rate of $0.5^{\circ}C/min$ down to $750^{\circ}C$ after the solution treatment. Then, both specimens were aged at $750^{\circ}C$ for 5 hours. Under two different heat treatment conditions, the low cycle fatigue (LCF) test was performed at $600^{\circ}C$ and room temperature (RT). Only cyclic hardening continued from the beginning until fracture at all strain amplitudes during LCF at $600^{\circ}C$. This phenomenon was attributed to the increase in the dislocation density due to cyclic deformation, which resulted in the interaction between the newly created dislocations and precipitates. Cyclic hardening followed by saturation and cyclic softening was observed at RT. Cyclic softening was attributed to the dislocation annihilation rate exceeding the dislocation generation rate. Other probable factor for cyclic softening was some cavities formed around grain boundaries after 20 cycles. WQ and FC have a similar LCF behavior at RT and $600^{\circ}C$ as shown in the cyclic stress response curves.

• Journal of Life Science
• /
• v.19 no.8
• /
• pp.1177-1182
• /
• 2009

In order to establish in vitro infection model for research of plant pathogen based on tissue softening disease in napa cabbage, eighty independent bacterial strains were isolated from the softened napa cabbage tissues. Eight bacterial isolates were primarily screened with the generation of reproducible tissue softening disease to fresh napa cabbages within 24${\sim}$48 hours after inoculation. Through various microbiological biochemical and morphological examinations, three Gram (-) isolates which harbor independent biological properties were finally chosen, and named as RBI, RB2 and RB6. Collective results obtained from API 20E test and analyses of VITEK 2 COMPACT and nucleotide sequences of 165 rRNA of each isolate proposed that isolates RBI and RB2 are close to the Erwinia carotovora subsp. odorifera, and RB6 is close to the Erwinia carotovora subsp. carotovora. These isolates grew optimally at $30^{\circ}C$ with neutral pH culture condition. The isolates caused softening tissue disease with dose-dependent manner regardless of pre-surface damages of napa cabbage. Minimum dose to cause soft rot disease for RBI, RB2 or RB6 were $8.0{\times}10^8$ CFU/mt $10^9$ CFU/ml or $4.7{\times}10^6$ CFU/ml respectively. These isolates caused tissue softening disease to eggplant, paprika and napa cabbage out of 14 different tested vegetables, indicating that these isolates damages specific plant tissues. The bacterial isolates obtained in this research and in vitro plant infection model will be adapted in the understanding of the mechanism of pathogenesis by plant pathogen.