• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.251-256
• /
• 2001

Recently, as industrialization is rapidly growing and the standard of life is rising, the quantities of waste glasses have been hastily increased and most of them are not recycled but abandoned. It cause some problems such as the waste of natural resources and environmental Pollution. Therefore, this study was conducted basic experimental research to analyze the possibilities of recycling of waste glasses(crushed waste glasses outbreaking from our county such as brown, green, colorlessness) as fine aggregates for concrete. Test results of fresh concrete, slump and compacting factors decrease because grain shape is angular and air content increase due to involving small size particles so much in waste glasses. Also compressive, tensile and flexural strengths decrease with increase of the content of waste glasses. In conclusion, the content of waste glasses below 30% is reasonable

• Journal of the Korean Ceramic Society
• /
• v.29 no.4
• /
• pp.253-258
• /
• 1992

ZnO varistors were prepared by the organochemical method which used citric acid and ethylene glycol as gelling agents. The microstructure of the sintered specimens exhibited small grains, uniform grain size distribution, and few intragranular pores. Thermal decomposition of the organic resin formed during the powder preparation process was completed around 450$^{\circ}C$. No significant changes were observed in microstructure and current voltage characteristic with respect to calcination temperatures. A major advantage of the organochemical method used in this experiment is a possible uniform mixing of trace amounts of dopants. Therefore, this powder preparation method seems promising in investigating the effect of Li or In ion, which is added in ppm level to ZnO varistors, on the pulse respose characteristic.

• Journal of the Korean Ceramic Society
• /
• v.24 no.3
• /
• pp.207-214
• /
• 1987

This paper is to determine the effect of binder burnout time and heating rate on the electrical propertries of type II multilayer ceramic capacitors(MLC). The quality of multilayer ceramic capacitor depends suitable on the binder burnout time, which is determined for at least 24 hours in the PVB-binder system. It is suggested that theelectrical properties of multilayer ceramic capacitor is due to the control of heating rate, with the dipole moment density from grain size distributiion. Comparing the fast firing with slow, we observed a small but consistent improvement in the electrical properties.

• Journal of Welding and Joining
• /
• v.8 no.1
• /
• pp.43-53
• /
• 1990

The transient temperature distribution in the continuous friction welding 304 stainless steel bars is investigated by experimental and analytical methods. It is calculated by F.D.M. (finite difference method). The heating pressure, the rotational speed and friction coefficient obtained from experiment are used to determine the heat input at the contacting surface. Thermal properties of the workpiece are the function of temperature. The calculated temperature is well coincided with the measured value. The grain size at weld interface is extremely small due to the severe plastic deformation at high temperature, and result of this refined zone reveals higher hardness value. Because the HAZ is very narror about 2-3 mm, welding defects do not occure.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.123-124
• /
• 2004

This study was investigated on the impact toughness and microstructure of welded metal and heat affected zone for Hi Nitrogen TiN Steel. With welding procedures, welding heat input applied were 30, 79 and 264 kJ/cm. TiN steel has shown very small prior austenite grain size for all the welding heat input applied, which was considered to result from the effect of TiN particles. In case of single SAW and EGW welding, the dilution rate of base metal into the weld was not high, resulting that there were no significant effects of base metal chemical composition on the mechanical properties of welds. However, TSAW with double Ypreparation carried very high dilution rate so that TiN steel has impaired the toughness of weld metal because N content in the weld was increased through the dilution of base metal.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1103-1109
• /
• 2010

In this paper in order to analyze the mechanical properties, the permeability and the freezing properties of SB-2 materials which are mainly used with the subbase materials on the rod. For this ends, a series of the physical test, the permeability test and the freezing test were carried out the samples mixed the small aggregate and the big aggregate from which was re-classified the SB-2. From the test results, it was analyzed the characteristics of permeability and the characteristics of freezing of the samples.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.6
• /
• pp.207-213
• /
• 2001

Shaking table tests to investigate the dynamic friction behavior of interfaces between dense dry granular soils and construction material(concrete) were performed and the results are reported. The results show the variation of dynamic interface friction coefficients between dense dry granular soils and construction material was small in the sliding velocity range employed in this study. It was also observed that dynamic interface friction coefficients decreased as mean grain sizes of granular soils increased. These coefficients were compared with the friction coefficients obtained from the peak internal friction angles of the same granular soils by plane strain compression tests.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.903-908
• /
• 2002

The production of waste glasses has been increased with the development of industry. The utilization of waste glass for concrete can cause the concrete to be cracked and to be weakened due to an expansion by alkali-silica reaction(ASR). When used the fibers with waste glass, there is an effect on reduction of expansion and strength loss due to ASR between the alkali in the cement paste and the silica in the waste glass. In this study, we conducted basic experimental research to analyze the possibilities of recycling of amber waste glass as fine aggregates for steel fiber reinforced concrete. Test results of fresh concrete. slump is decreased because grain shape is angular and air content is increased due to involving small size particles so much in waste glasses. Also. tensile and flexural strengths increased as the content of steel fibers increased. In conclusion, the content of waste glass below 40% is reasonable and usage of pertinent admixture is necessary to obtain workability or air content.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.9 no.4
• /
• pp.25-33
• /
• 2000

The reorientations of the atoms by frictional shear deformation at the surface induce cracks at the boundary of the grain. The cracks grow and propagate in regions where the hydrostatic component of stress is least compressive because the compressive component restores the cracks by three-dimensional crystallizing $\pi$-bondings. The materials with Lder's band have very small amount of wear at the initial state. It suggests that initial frictional shear deformation be consumed to the formation of the Lder's band. The average wear amounts of the materials increase very steeply as the øu the stress-strain ratio at the ultimate point, decreases.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S1
• /
• pp.113-117
• /
• 1995

MOCVD of Cu films were carried out on gold-TiN(1000$\AA$)/Ti/Si wafers from hexafluoroacetylacetonate-Cu(l) vinyltrimethylsilane, Cu(l)(hafac)(vtms), in a small cold-wall type reactor. Effects of the substrate and bubbler temperatures on the film growth rate were studied, and a film with $\rho$=1.8$\pm$0.1$\mu$$\Omega$.cm could be deposited 150nm/min at Ts=200 and Tb=$30^{\circ}C$, respectively. The initial stage of the film formation was also investigated by in-situ laser reflectivity monitoring combined with SEM observations, based on which variations in the film properties depending on the growth conditions were discussed in terms of the nucleation rate and grain size.