• 한국전기전자재료학회논문지
• /
• 제11권4호
• /
• pp.327-333
• /
• 1998

The influence of slow cooling and annealing time in $O_2$in MPEG process on $J_c$ was investigated. From the measurement of $J_c$,SEM and XRD, it was observed that the critical current density was related with the slow cooling time and annealing time in $O_2$. The value of $J_c$ was the highest at slow cooling time of 40 hour. And also, the value of $J_c$ along the annealing time in $O_2$in the case of the slow cooling time of 40 hours was inclined to increase with annealing time. Consequently, it can be suggested that proper slow cooling time and annealing time after slow cooling in MPMG process be important to improve the critical characteristics.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.185-188
• /
• 1997

The influence of slow cooling and annealing time in $O_2$ during melting and growth step in MPMG process on J$_{c}$ was investigated. Through the measurement of J$_{c}$ SEM and XRD, it can be observed that the critical characteristics were related with the slow cooling time and annealing time in 02 for melting and growth step of MPMG process. The distribution of critical current density with slow cooling time was the porabolic form and the value of J. was the highest at the 40 hour slow cooling time. And also, the value of J$_{c}$, along the annealing time in $O_2$ in the case of the slow cooling time 40 hour was inclined to increase with annealing time. Consequently, it can be suggested that proper slow cooling titre and annealing time along slow cooling in MPMG process be important to improve the critical characteristics.stics.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권4호
• /
• pp.221-225
• /
• 1999

This paper shows the parameters to affect the critical characteristic of YBaCuO superconducting bulk fabricated by MPMG (Melt Powdered Melt Growth)process. In order to investigate proper processing variables, the effect of the holding time at the melting temperature and that of the slow cooling time in $O_2\; ambient\; on\; the\; J_c$ were experimented. And then with the above obtained heat treatment conditions, the effects of addition of $Y_2BaCuO_5\; and\; Ag\; on\; the\; J_c$ were also investigated. A proper slow cooling time yields phase transformation from Tetragonal $(YBa_2Cu_3O_6)$ to Orthorhombic $(YBa_2Cu_3O_7)$ during an annealing time in $O_2$. Ag addition plays a role in increasing the $T_c\; and\; the J_c$, but the magnetization decreases. The $J_c$ and the magnetization increase with addition of Y211. $J_c$ of the sample added Ag 10wt% is superiorover 3000 G. Proper holding time, slow cooling time and amount of impurity addition are important parameters in fabricating the YBaCuO bulk by MPMG process with high $J_c$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.852-855
• /
• 2003

Gas-Assisted Injection Molding(GAIM) process, that can be used to provide a hollow shape in a molding, is a variant of the conventional injection molding process. GAIM has many advantages such as reduction of material, sink mark. warpage. and lower injection pressure. Thus, GAIM has been widely applied in the industry to make moldings with a hollow channel such as handles, TV frames and so on. On the other hand, GAIM has some disadvantages such as slow cooling time and flow marks. In the disadvantages, hot gas core causes slow cooling of a molding and the overflow. which is to prevent flow mark. is waste of materials. To solve these problems, we developed a new GAIM system that we called RGIM(Reverse Gas Injection Molding). The RGIM has two special units; one is the overflow buffer, which is used for reduction of a material, and the other tile air unit, which is used for faster cooling of a molding. We conducted an experiment and simulation to verify the efficiency of the RGIM system. Through experiments and simulation, we confirmed the effectively operating of the RGIM system and extracted the optimum process conditions.

• 대한기계학회논문집B
• /
• 제27권3호
• /
• pp.367-373
• /
• 2003

The present study investigates the fire suppression characteristics using a water mist fire suppression system. The fire extinguishing times are measured for various fire sources, fuel types, and different total flooding rates of water mist. Pool fire with hydrocabon fuel is successfully extinguished within a minute under the operating conditions of the water mist system. Two different regimes of the smoke layer cooling are observed, such as rapid and slow cooling processes. The regimes are divided by threshold time which is calculated with auto-correlation function. The threshold time for the initial cooling decreases with increasing water flow-rates and fire sources. These initial cooling effects play an important role in preventing the occurance of flashover fire by the initial fire suppression.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.58-67
• /
• 2003

An automotive engine cooling system is closely related with overall engine performances, such as reduction of fuel consumption, decrease of air pollution, and increase of engine life. Because of complex reaction between each component, the direct experiment, using a vehicle, takes high cost, long time, and slow response to the system change. Therefore, a computer simulation would provide the designer with an inexpensive and effective tool for design, development, and optimization of the engine cooling system over a wide range of operating conditions. In this work, it has been predicted the thermal performance of the engine cooling system in cases of stationary mode, constant speed mode, and city-drive mode by mathematical modelling of each component and numerical analysis. The components are engine, radiator, heater, thermostat, water pump, and cooling fans. Since the engine model is the most important, that is divided into eight sub-sections. The volume mean temperature of eight sub-sections are simultaneously calculated at a time. For detail calculation, the radiator and heater are also divided into many sub-sections like control volumes in finite difference method. Each sub-section is assumed to consist of three parts, coolant, tube with fin, and air. Hence it has been developed the simulation program that can be used in case of design and system configuration changes. The overall performance results obtained by the program were desirable and the time-traced tendencies of the results agreed fairly well with those of actual situations.

• 한국세라믹학회지
• /
• 제26권4호
• /
• pp.459-470
• /
• 1989

Single crystals of rare-earth iron garnets were grown from solutions of molten lead oxide, lead fluoride, baric oxide, iron oxide, and the oxides of yttrium, samarium orgadolinium. The crystals were grown by slow cooling technique. A convenient composition was 41.8mol% PbO, 20.59mol% PbF2, 8.23mol% B2O3, 20.00mol% Fe2O3 and 10.00mol% R2O3 where R is Y, Sm or Gd. For this experiment, platinum crucibles of size 20, 30cc and a vertical siliconit tube furnace were used. The precipitation temperature of YIG was observed in the range of 115$0^{\circ}C$-112$0^{\circ}C$ and the optimum growth conditions in this experiment were determined. The nucleation rate was controlled by the holding time after the fast colling, the growth rate by the slow cooling conditiions. The form of the grown YIG crystals showed a combination of {110} and {211}, and the size of the crystals grown in this experiment was up to about 9mm under the conditions of holding time 16hour, cooling rate 2$^{\circ}C$/hr. and temperature range 115$0^{\circ}C$-90$0^{\circ}C$. The precipitatin temperature of SmIG was observed in the range of 105$0^{\circ}C$-98$0^{\circ}C$ and the size of the crystals grown in this experiment was up to about 5mm under the conditiions of holding time 16hours, cooling rate 2$^{\circ}C$/hr. and temperature range 100$0^{\circ}C$-80$0^{\circ}C$.

• 천문학회지
• /
• 제29권spc1호
• /
• pp.253-254
• /
• 1996

To understand the dynamical structures of stellar wind bubble, one and two-dimensional calculations has been performed. Using FCT Code with cooling effects and assuming constant mass loss rate and ambient medium density, we could divide stellar winds into the regime of slow and fast winds. The slow wind driven bubble shows initially radiative and becomes partially radiative bubble in which shocked stellar wind zone is still adiabatic. In contrast., the fast wind driven bubble shows initially fully adiabatic and becomes adiabatic bubbles with radiative outer shell. We also determine analytically the onset of thin-shell formation time in case of fast wind driven bubble with power-law energy injection and ambient density structure. We solve the line transfer problem with numerical results in order to calculate line profile of [OIII] forbidden line.

• 한국세라믹학회지
• /
• 제30권8호
• /
• pp.664-670
• /
• 1993

Potassium tetratitanate (K2Ti4O9) and Potassium hexatitanate (K2Ti6O13) fibers have been prepared by the slow-cooling calcination process in a temperature range from 125$0^{\circ}C$ to 95$0^{\circ}C$ using the K2CO3 and TiO2 as the starting materials. Optimum fiber growth conditions have been also investigated by changing the physical parameters, such as calcination time and temperature, and cooling rate. Relatively long K2Ti4O9 fibers ( 1.2mm) have been grown with quite a high aspect ratio (c/a 500)when the starting material with a nominal composition of K2O and TiO2 with 1:4 was calcined at 115$0^{\circ}C$ for 4h, and then was slowly cooled to 95$0^{\circ}C$ with a rate of 2$0^{\circ}C$/h. In case of a K2O.6TiO2 composition, acicular shaped K2Ti6O13 fibers with 20~300${\mu}{\textrm}{m}$ long and low aspect ratio (c/a 10~15) have been formed irrespective of the coolign rate. The growth condition of fibers have been discussed based upon the phase diagram of K2O-TiOa2.

• 한국정밀공학회지
• /
• 제11권2호
• /
• pp.173-181
• /
• 1994

A Cold spot temperature control system for the batch annealing furnace has been estabilished in order to reduce energy consumption to improve productivity and stabilize the propertics of products. Therefore we confirmed a relation between annealing cycle time and atmospheric gas, variation of coil cold spot temperature with time during heating and actual temperature measurements at mid-width of each coil during heating and actual temperature measurements at mid-width of each coil during soaking. The results of the tempaeature variation effect on the batch annealing are as follows. 1) Heating time is reduced to one half with increasing atmospheric gas flow rate and changing of atmospheric gas component from HNx to Ax gas, and annealing cycle time is reduced to 2.7 times. 2) In case of short time healing, the slowest heating part is the center of B coil, in case of long time heating, the low temperature point moves from the center of coil to inside coil. And the temperature in this part is higher than other parts when cooling. When finished heating, the cold spot is located 1/3 of coil inside in case of HNx atmospheric gas. But center of coil in case of Ax atmospheric gas. 3) The outside of top coil is the highest temperature point when heating, which becomes the lowest temperature point when cooling. So, this point becomes high temperature zone at heating and low temperature zone at cooling, It has relation according to atmospheric gas component and flow rate. 4) Soaking time at batch annealing cycle determination is made a decision by the input coil width, and soaking time for quality homogenization of 1214mm width coil must be 2.5 hours longer than that of 914mm width coil for the same ciol weight. 5) Annealing cycle time with Ax atmospheric gas is extended 1 hour in of slow cooling during 5 hours in order to avoid rapid cooling.