• Journal of the Korean Wood Science and Technology
• /
• v.31 no.3
• /
• pp.35-41
• /
• 2003

The mechanical and physical properties of wood are strongly dependent upon the slope of grain. Specially, tensile strength is more severely affected by the slope of grain. Therefore, tension tests were performed on small thin wood samples made from Pinus radiata with varying the slope of grain. Determining the tensile strength for clear thin wood samples the other variabilities associated with material, size, drying, defects, etc were discarded. Slope of grain was measured by the slope of grain indicator and actual slope of grain was also determined by a protractor. Correlation coefficients between machine measured and actual slope of grain for 40 pieces of 2×20 mm, 300 mm long Pinus radiata were 0.84 for wide face measurement. Results also showed that tensile strength and MOE from stress wave tests decreased with increasing the slope of grain. This study did not establish a relationships for tensile strength and MOE from stress wave with slope of grain. However, the trends of MOEs from stress wave test with both slope of grain are agreed well with Hankinson's equation. Predicted tension strength curve by Hankinson's equation was also agreed well with the experimental data over the range from 0 to 13 degrees for slope of grain.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.24 no.1
• /
• pp.64-78
• /
• 2019

The background concentrations of heavy metals in Korean coastal sediments were estimated using heavy metal data for 495 sediments obtained from 'National Marine Ecosystem Survey (Coastal ecosystem) in 2016-2017' and the extent of contamination was assessed. Al, Cs, and Li are chosen as appropriate indicators for sediment grain size. In the relationships between heavy metal and indicators concentrations, the lowest slope data were selected through the outlier removal and residual analysis, and the background concentrations were presented as a linear regression line between metal and indicator. Comparing the previous studies for the background concentrations of heavy metals in Korean coastal sediments, concentration levels were generally consistent but those for As and Cd were presented for the first time, and the background concentration using Li as the indicator was presented for the first time.

• Journal of Environmental Science International
• /
• v.20 no.7
• /
• pp.829-837
• /
• 2011

A study on the grain size change, sedimentary facies and age indicator of volcanic tephra was analysis through four cores (P1 ~ P4) at the Ulleung Basin in the East Sea of Korea. The two cores (P1 and P2) were collected in the northeastern side of the Ulleung Basin (about 2,000 m in water depth), while the other two cores (P3 and P4) with the water depth of about 1,500 m and 1,700 m, respectively, were collected from the continental slope of the southwestern and western side of the Ulleung Basin. Four sedimentary facies and eight sedimentary subfacies were identified. The four facies were massive sand, bioturbated mud, homogeneous mud, and laminated mud. The eight subfacies were further divided as pumiceous ash massive sand, scorieaous massive sand, plain bioturbated mud, pyrite filamented bioturbated mud, distinctly laminated mud, indistinctly laminated mud, thinly laminated mud and homogeneous mud. The homogeneous mud was not found in the core of P3 which is located in the western side of Ulleung Basin (close to the Korean coast). In the case of laminated mud facies, the thinly laminated mud facies was dominated in the lower part of core sequences of the Ulleung Basin (P1 and P2), while the indistinctly laminated mud were overally distributed in the core sequences from the continental slope of Ulleung Basin. The Tephra layers from the core sequences of central Ulleung Basin were more dominated and distinctive than those from the core sequences of continental slope. This is related to the distance from the volcanic source and the amount of sediment supply. The core locations of Ulleung-Oki Tephra layers in the central Ulleung Basin were in the upper part of core sequences, while those in the continental slope were in the lower part of core sequences. This is indicated that the amounts of sediment supply in the continental slope after the Ulleung-Oki eruption were very high and different sedimentary environment between upper and lower of Tephra layer.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.2
• /
• pp.99-114
• /
• 2020

The characteristics of the Brazilian tensile strengths(σ_t) parallel to the rock cleavages in Jurassic granite from Geochang were analysed. The evaluation for the six directions of rock cleavages was performed using the parameter values on microcrack length and the above strength. The strength values of the five test specimens belonging to each direction were classified into five groups. The strength values of these five groups increase in order of group A < B < C < D < E. The close dependence between the above microcrack and strength was derived. The analysis results of this study are summarized as follows. First, the chart showing the variation and characteristics of strength among the three rock cleavages were made. In the above chart, the strength values of six directions belonging to each group were arranged in order of rift(R1 and R2), grain(G1 and G2) and hardway(H1 and H2). The strength distribution lines of the five groups concentrate in the direction of R1. And the widths among the above five lines indicating strength difference(Δσ_t) are the most narrowest in R1 direction. From the related chart, the variation characteristics among the two directions forming each rock cleavage were derived. G2(2)-test specimen shows higher value and lower value of the difference in strength compared to the case of G1(1)-test specimen. These kinds of phenomena are the same as the case between the test specimen H2(2) and H1(1). The strength characteristics of the above test specimens (2) suggest lower microcrack density value and higher degree of uniformity in the distribution of microcracks arrayed parallel to the loading direction compared to those of test specimens (1). The six strength values belonging to each group were arranged in increasing order in the above chart. The strength values of the test specimens belonging to both group D and E appear in order of R1 < R2 < G1 < H1 < G2 < H2. Therefore, the strength values of group D and E can be indicator values for evaluating the six directions of rock cleavages. Second, the correlation chart between slope angle(θ) and strength difference(Δσ_t) were made. The values of the above two parameters were obtained from the five strength distribution lines connecting between the two directions. From the chart related to rift plane(G1-H1, R'), grain plane(R1-H2, G') and hardway plane(R2-G2, H'), the slope values of linear functions increase in order of R'(0.391) < G'(0.470) < H'(0.485). Among three planes, the charts related to hardway plane show the highest distribution density among the five groups. From the related chart for rift(R1-R2, R), grain(G1-G2, G) and hardway(H1-H2, H), the slope values of linear functions increase in order of rift(0.407) < hardway(0.453) < grain(0.460). Among three rock cleavages, the charts related to rift show the highest frequency of groups belonging to the lower region. Taken together, the width of distribution of the slope angle among the three planes and three rock cleavages increase in order of H' < G < R' < R < G' < H. Third, the correlation analysis among the parameters related to microcrack length and the tensile strengths was performed. These parameters may include frequency(N), total length(Lt), mean length(Lm), median length(Lmed) and density(ρ). The correlation charts among individual parameters on the above microcrack(X) and corresponding five levels of tensile strengths for the five groups(Y) were made. From the five kinds of correlation charts, the values of correlation coefficients(R²) increase along with the five levels of strengths. The mean values of the five correlation coefficients from each chart increase in order of 0.22(N) < 0.34(Lt) < 0.38(ρ) < 0.57(Lmed) < 0.58(Lm). Fourth, the correlation chart among the corresponding maximum strength for group E(X) and the above five parameters(Y) were made. From the related chart, the values of correlation coefficient increase in order of 0.61(N) < 0.81(Lt) < 0.87(ρ) < 0.93(Lm) < 0.96(Lmed). The two parameters that have the highest correlations are median length with maximum strength. Through the above correlation analysis between microcrack and strength, the credibility for the results from this study can be enhanced.