• 제목/요약/키워드: sliding-type bearing

검색결과 62건 처리시간 0.029초

고탄소크롬 베어링강 2종(SUJ2) 베어링강에 증착된 저마찰 코팅의 트라이볼로지적 특성 연구 (A Study on the Tribological Characteristics of Low Friction Coating Deposited on SUJ2 Bearing Steel)

  • 강경모;신동갑;박영훈;김세웅;김대은
    • Tribology and Lubricants
    • /
    • 제34권6호
    • /
    • pp.254-261
    • /
    • 2018
  • In order to reduce resistance torque and energy loss, minimizing friction between race surface and rolling elements of a bearing is necessary. Recently, to reduce friction in bearing element, solid lubricant coating for the bearing raceway surface has been receiving much attention. Considering the operating conditions of real bearings, verifying the effect of solid lubricant coatings under extreme conditions of high load that is more than 1 GPa is necessary. In this study, we evaluated the friction and wear characteristics of SUJ2 bearing steels deposited by carbon-based coatings (Si-DLC, ta-C), $MoS_2$ and graphite. In case of $MoS_2$ and graphite coatings, different surface treatments were applied to the coatings to verify the effect of surface treatment. A pin-on-disc type tribotester was used to evaluate the tribological characteristics of the coatings. It was possible to quantitatively estimate the friction and wear characteristics of solid lubricant under dry and lubrication conditions. The carbon-based coatings improved the friction and wear properties of SUJ2 bearing steels under the high load condition, but $MoS_2$ and graphite coatings were not suitable for high load conditions due to its low hardness. Different friction and wear behaviors were found for different substrate surface treatment method. Also, it was confirmed that solid lubricant coatings had a more positive effect than just applying the lubricant for improving the tribological characteristics.

수-윤활용 플라스틱 베어링 개발에 관한 연구 (Development of Water-lubricated Plastic Bearings)

  • 공호성;한흥구
    • Tribology and Lubricants
    • /
    • 제39권6호
    • /
    • pp.235-243
    • /
    • 2023
  • This paper presents the fabrication process of water-lubricated plastic bearings. Plastic bearings require good mechanical properties and tribological properties as well as elasticity and shock resistance, especially when lubricated in dirty water conditions. In this study, sleeve-type plastic bearings are produced by winding a prepreg sheet, which primary contains nitrile rubber (NBR)-modified epoxy, self-lubricating fillers, and various types of lattice-structured reinforcing fibers such as carbon, Aramid, and polyethylene terephthalate. A thermosetting epoxy is chemically modified with NBR to impart elasticity and low-friction characteristics in water conditions. Experimental investigations are conducted to examine the mechanical and tribological characteristics of the developed bearing materials, and the results are compared with the characteristics of a commercial plastic bearing (Thordon SXL), well known as a water-lubricated bearing. A Thordon bearing (mainly composed of polyurethane) exhibits an extremely low load-bearing capacity and is thus only suitable for medium loading (1~10MPa). The tribological characteristics of the test materials are evaluated through Falex block-on-ring (LFW-1) friction and wear tests. The results indicate that friction exhibited by the carbon-fiber-reinforced NBR-10wt.%-modified epoxy composite material, incorporated with the addition of 20wt.% UHMWPE and 6wt.% paraffin wax, is lower than that of the Thorden bearings, whereas its wear resistance surpass that of Thorden ones. Because of these features, the load carrying capacity of the fabricated composite (>10MPa) is higher than that of the Thorden bearings. These results confirm the applicability of water-lubricated plastic bearing materials developed in this study.

3D 프린팅된 표면의 슬라이딩 방향에 따른 트라이볼로지적 특성 연구 (A Study on Tribological Properties of 3D-Printed Surface with Respect to Sliding Orientation)

  • 심재웅;크리스찬 니콜라스 디 카로;서국진;김대은
    • Tribology and Lubricants
    • /
    • 제35권6호
    • /
    • pp.337-342
    • /
    • 2019
  • This paper presents an experimental investigation of friction and wear characteristic with respect to patterns occurring on the surface of 3D printed polymer products by fused deposition modeling method. The purpose of this study was to investigate the effect of the patterns and sliding directions on the tribological properties of 3D printed polymer surface. A cubic specimen was printed using polylactic acid filament as the printing material. Friction tests were conducted for different directions with respect to the patterns that were generated on the top and the side surfaces of the specimen, by using a ball-on-reciprocating type tribotester. SUJ2 bearing ball of which the diameter was 11 times greater than the width of the largest pattern was used as the counter surface to assess the frictional behavior. Friction tests were conducted on the top and the side surfaces with respect to the patterns in 3 (0°, 45°, 90°) different directions respectively. Coefficient of friction increased as cycles increased in all cases. The results of the tests showed that the lowest coefficient of friction was measured with the 45° sliding direction on the side surface. The wear rate was the lowest at 45° sliding direction on the side surface, while it was the highest at 0° sliding direction on the top surface. Coefficient of friction of about 0.45 was determined to be the converging value on the top compared to the side surface.

사판식 유압 피스톤모터의 성능특성 분석 (Analysis of Performance Characteristics of Swash-Plate-Type Hydraulic Piston Motor)

  • 이용범;김광민
    • 대한기계학회논문집A
    • /
    • 제36권11호
    • /
    • pp.1441-1446
    • /
    • 2012
  • 유압피스톤모터는 정압베어링부분의 마찰손실과 용적손실, 기구적 운동부분의 마찰손실, 오일의 관로저항에 의한 압력저하, 압축성에 의한 체적손실 그리고 하우징 오일 처닝(churning) 손실 등이 있다. 이러한 손실 중에서 일정한 틈새의 유막(oil film, $8{\sim}15{\mu}m$)으로 고속 회전하는 피스톤 슈(piston shoe)와 슈 플레이트(shoe plate) 사이 정압베어링 부분의 마찰 및 용적손실이 유압모터의 전체효율을 좌우 한다. 본 연구에서는 최고압력 35MPa, 최고회전수 2500rpm, 배재용적 320cc/rev급 2속(2-speed) 초대형 굴삭기의 주행모터용 유압피스톤모터를 대상으로 정압베어링비가 유압모터의 전 효율에 미치는 영향을 실험적으로 분석하였다.

$Al_{2}O_{3}$$TiO_{2}$를 플라즈마 용사한 코팅재의 마모 특성 (Wear Characteristics of $Al_{2}O_{3}\;and\;TiO_{2}$ Coating Materials by Plasma Spray)

  • 김성익;김희곤;김귀식
    • Tribology and Lubricants
    • /
    • 제22권5호
    • /
    • pp.282-289
    • /
    • 2006
  • This paper is to investigate the wear behaviors of two type ceramics, $Al_{2}O_{3}\;and\;TiO_{2}$, by coated plasma thermal spray method under the lubricative environment. The lubricative environments are grease fluids, a general hydraulic fluids, and bearing fluids. The wear testing machine used a pin on disk type. Wear characteristics, which were friction force, friction coefficient and the specific wear rate, according to the lubricative environments were obtained at the four kinds of load and sliding velocity is 0.2 m/sec. After the wear experiments, the wear surfaces of the each test specimen were observed by a scanning electronic microscope.

EHA 펌프용 피스톤 슈 정압베어링의 경계 마찰 성능 개선 (Performance Improvement of the Hydrostatic Piston Shoe Bearing of an EHA-Piston Pump under Boundary Friction Conditions)

  • 홍예선;권용철;김종혁;이성렬;김병곤;문진삼;김재환
    • 드라이브 ㆍ 컨트롤
    • /
    • 제11권2호
    • /
    • pp.30-35
    • /
    • 2014
  • The pumps of electro-hydrostatic actuators operate most frequently in boundary lubrication speed range, as they compensate for the position control errors as a control element. When conventional swash plate type piston pumps are applied to electro-hydrostatic actuators, the frictional power losses as well as the wear rate of sliding components, such as piston shoes can increase drastically under the boundary friction condition. In this paper, the power losses of the piston shoes were investigated which were engendered by a frictional solid-to-solid contact and leakage flow rate of their hydrostatic bearing. In order to reduce them, DLC-coating was applied to the swash plate and the ball joint of pistons along with its effects were demonstrated. In addition, it was also shown that the wear rate of the piston shoes could be markedly reduced using the DLC-coated swash plate.

A Study on the Application of Skirt Plates on Jacket Support Structures of Offshore Wind Turbines

  • Choi, Byeong-Ryoel;Choi, Han-Sik;Jo, Hyo-Jae;Lee, Sang-Hyep;Park, Young-Ho
    • Journal of Advanced Research in Ocean Engineering
    • /
    • 제4권2호
    • /
    • pp.47-52
    • /
    • 2018
  • The Korea Offshore Wind Power (KOWP) is planning to construct offshore wind energy farms with an overall rated power of 2.5 GW in the south-western coast of the country until 2019. Various types of support structures for offshore wind turbines have been proposed in the past. Nevertheless, in South Korea, jacket structures have in general, been applied as support structures for offshore wind turbines owing to the many accumulated experiences and know-how regarding this kind of support structure. The choice of offshore structure is mainly influenced by site conditions such as seabed soil type and sea environment during installation. In installing jacket sets on the seabed, the mudmat is necessary to maintain the equilibrium of the jacket without the aid of additional devices. Hence, this study proposes the installation of skirt plates underneath the bottom frame of jackets in order to improve the installation stability of jacket structures under rougher sea conditions. To confirm the effect of skirt plates, installation stability analyses considering overturning, sliding and bearing capacity have been performed. From the results, it is shown that jacket structures with skirt plates can contribute to improving the sliding stability of the structures of new wind power farms, while providing economic benefits.

AlSiMg/TiC 복합 용사피막 : 마모 특성 (II) (Thermal Sprayed AlSiMg/TiC Composite Coatings : Wear Characteristics (II))

  • 양병모;변응선;박경채
    • Journal of Welding and Joining
    • /
    • 제18권5호
    • /
    • pp.105-111
    • /
    • 2000
  • The wear behavior of thermal sprayed AlSiMg-40TiC composite coatings were studied as a function of load and sliding velocity under unlubricated conditions. Experiments were performed using a block-on-ring(WC-6wt%/Co, Hv 1500) type. The tests were carried out a various load(30∼ 125.5N) and sliding velocity(0.5∼2.0m/s). Three wear rate regions were observed in the AlSiMg-40TiC composite coatings. The wear rate in region I at low load (less then 8N( were less than 1×{TEX}$10^{-5}${/TEX}㎣/m. Low wear rates in region I resulted from the load-bearing capacity of TiC particles. The transition from region I to II occurred when the applied load exceeded the fracture and pull-out strength of the particles. The TiC fractured particles trapped between the specimen and the counterface acted as third-body abrasive wear. The subsurface layer worn surface in region II was composed of the mechanically mixed layer (MML). The wear rate increase abruptly above a critical load (region III). The high wear rate in region III was induced by frictional temperature and involves massive surface damage.

  • PDF

연약지반방파제의 설계를 위한 안전율 평가 (Evaluation of Safety Factors for the Soft Ground Breakwater Design)

  • 권오순;장인성;박우선;염기대
    • 한국해안해양공학회지
    • /
    • 제15권4호
    • /
    • pp.197-206
    • /
    • 2003
  • 최근 특별한 연약지반 처리공법을 적용하지 않고 자중을 감소시키고 구조적인 특성을 이용하여 연약지반 위에 설치하는 방파제가 제안ㆍ개발되고 있다. 본 연구는 이러한 연약지반 방파제의 설계를 위하여 현재 사용하고 있는 중력식 방파제의 설계에서 사용하고 있는 활동, 전도 및 지지력에 대한 안전율 평가 방법을 수정 제안하기 위하여, 다양한 조건의 방파제 형상과 지반조건에 대하여 제안된 방법으로 계산된 안전율과 유한요소해석 결과 얻어진 최대 횡방향 변위를 이용하여 안전율 산정방법의 타당성을 검증하였다. 해석 및 검증 결과, 제안된 안전율 산정방법은 타당한 것으로 나타났다.

$Cr_2O_3$$ZrO_{2}$ 플라즈마 용사한 코팅재의 마모 특성 (Wear Characteristics of $Cr_{2}O_{3}\;and\;ZrO_{2}$Coating Materials by Plasma Spray)

  • 김성익;김희곤;이봉길;김귀식
    • Tribology and Lubricants
    • /
    • 제22권6호
    • /
    • pp.335-341
    • /
    • 2006
  • This paper reports the wear characteristics of two types of coating materials, which are $Cr_2O_3$ and $ZrO_2$, by coated plasma thermal spray method. The wear test was carried out under air, grease, and bearing fluid conditions. The wear testing machine of a pin-on disk type were used to measure friction forces, friction coefficients and the weight losses of the coating specimens on the various sliding velocity and loading condition. The wear surface of specimens were observed by scanning electron microscope (SEM) photographs.