• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.4
• /
• pp.71-82
• /
• 2020

Traffic accidents due to excessive speed frequently occur in places where traffic signal controllers are installed, places where sharp curves exist, or places where the traffic signal cycle does not match the current time. These traffic accidents cause economic loss due to the destruction of road facilities and structures, and cause a big problem of increasing the number of traffic accident deaths. When a traffic accident occurs, leaving a tire mark before or after a car crash, pre-collision speed of the car is calculated using the law of conservation of momentum or the skid mark formula. In the skip skid mark generated in ABS brake vehicles and the combshaped yaw mark generated by tire trace caused by lateral sliding, there is a difference of 30-40% in the reliability of the vehicle speed calculated by the smite mark. In this paper, we propose an algorithm that can improve the calculation reliability in vehicle speed by using skid marks in order to compensate for this problem. In addition, we present an intelligent speed calculation algorithm for traffic safety and a computer simulation in order to prevent traffic accidents by estimating the speed of a vehicle, using Skid marks, Yaw marks, and ABS brake characteristics and fuzzy rules.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.40-40
• /
• 2000

Generally a RF AGC controls the roll gap using the variation of rolling force caused by the roll eccentricity and the entry thickness of material, but these can not be classified. The Feed- forward AGC method, which controls the next stand roll 9ap by estimation the skid mark of the previous stand output thickness is needed to supplement the shortage of RF AGC. In this paper, an improved filtering method of skid mark which take account of the kinds of materials, the final objective thickness and the roll speed is proposed, In addition, an improved estimation method of control point using the speedometer and looper angle is suggested, Via simulation, the performance improvement of the suggested FF AGC method is verified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.12-18
• /
• 2009

Skid mark and coefficient of friction are usually utilized to calculate the velocity and behavior of vehicles. For a critical case such as traffic accident reconstruction, however, the initial velocity of the car should be calculated precisely. In this study, in order to estimate the speed at the brake onset, rapid braking tests were executed on the proving ground. We compared with a skid length and wheel locking time of an expert driver and a general person. We verified that the skid mark of expert driver occurs longer than general person's. A new method is proposed to determine the speed of a vehicle at the brake onset of maximum braking, which could be applied to a reconstruction of vehicle with Non-ABS.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.168-171
• /
• 2003

Generally RF AGC (Roll Force Automatic Gauge Control) controls the roll gap using the variation of rolling force caused by the roll eccentricity and the entry thickness of material, but RE AGC takes the bad effect of the roll eccentricity. The Feed-forward (FF) AGC method, which controls the next stand roll gap by the estimation of the thickness variation due to skid mark is needed to supplement the shortage of RF AGC. In this paper, an adaptive filtering method which takes account of the kind of material, the final objective thickness and the rolling speed is proposed to predict skid mark thickness variation. In addition, an improved estimation method of control point using a speedometer and looper angle is suggested. Via on line test, the performance improvement of the suggested FF AGC method is verified.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.150.5-150
• /
• 2001

This paper deals with a modified repetitive control method for compensating automatic gauge control (AGC) to reduce the effect of skid mark which directly influence the quality of products in plate mill process. Since the skid mark on the plate have thermal difference, it makes a different stretching rate and deflection of thickness. Firstly, the (AGC) system and the plate mill process are described by considering function in each control levels. The skid mark of the plate in practical control fields is shown. Also, its frequency variation is given by on-line FFT analysis method. Secondly, a key idea of the modified repetitive control method with time varying period disturbance is represented and compared with standard repetitive control method. Lastly, in simulation ...

• Journal of Korean Society of Transportation
• /
• v.29 no.3
• /
• pp.115-122
• /
• 2011

This paper investigates the accuracy of the vehicle pre-braking speed estimated based upon measured skidding distance. Driver ordinarily takes sudden braking when urgent situation is developed in the front or when the driver is involved in an unexpected situation, and the driver may be inflicted upon an accident depending on the required stopping distance. Among factors influencing the stopping distance of vehicle such as recognition response time of driver, performance of vehicle's braking device, and state of road surface etc, pre-braking speed is seemingly the most important influencing factor. Currently, in the investigating section of traffic accidents, the state of overspeed is determined by the pre-skidding speed calculated based on the length of skid mark. In order to identify the accurate cause of the accident, it is strongly recommended that estimation of pre-braking speed should be estimated taking into account speed reduction during transient time. In this study, we propose a method for estimating more accurate exact speed information of vehicle at the time of traffic accident. The outcomes from this study potentially help better understanding of the characteristics of vehicle for traffic safety in the future.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.1
• /
• pp.125-132
• /
• 2012

In this paper, We proposes FE-SM/SONN for recognizing blurred and smeared skid mark image caused by sudden braking of a vehicle. In a blurred and smeared skid marks, tread pattern image is ambiguous. To improve recognition of such image, FE-SM/SONN reads skid marks utilizing Fuzzy Logic and distinguishing tread pattern SONN(Self Organization Neural Networks) recognizer. In order to substantiate this finding, 48 tire models and 144 skid marks were compared and overall recognition ratio was 89%. This study showed 13.51% improved recognition compared to existing back propagation recognizer, and 8.78% improvement than FE-MCBP. The expected effect of this research is achieving recognition of ambiguous images by extracting distinguishing features, and the finding concludes that even when tread pattern image is in grey scale, Fuzzy Logic enables the tread pattern recognizable.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.174-179
• /
• 2007

The transient brake time or distance is one of very important factors to guess the vehicle speed to inspect an automobile accident. But, it is usual that the vehicle speed is estimated by using only skid mark without considering the transient brake distance. Deceleration and the friction coefficients of tire and road surface play an important role in calculating the brake distance. In this paper, a scheme is presented to estimate more accurate automobile speed. The scheme contains the effect of the transient brake distance on the speed. Experiment was carried out on the asphalt, unpacked road to get relationships between the speeds and the skid mark distances, and to get the transient brake time. The experimental results were utilized to construct the equation to approximate more realistic vehicle speeds.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.109-114
• /
• 2007

Skid mark and coefficient of friction are usually utilized to calculate the velocity and behavior of vehicles. For a critical case such as traffic accident reconstruction, however, the initial velocity of the car should be calculated precisely. In this study, the skid marks on dry asphalt pavement were measured, and the velocity at brake onset was precisely recovered. A passenger car with new tires and non-contact optical speedometer were set up for the tests. A new methodology to determine the more precise velocity for Non-ABS vehicle at braking onset were suggested.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.1
• /
• pp.113-120
• /
• 2010

In case the traffic accident occurs, skid mark is very important factor to calculate the car speed. Especially, for the purpose of objective and scientific inspection, traffic accidents should be appraised and inspected by righteous material evidences, computer simulation, and studies such as automobile engineering, traveling and collision accident dynamics, road and traffic engineering. In this paper, it displays the results of studying cases with the reasons of traffic accidents by analyzing and studying automobile kinetics, real traffic accidents and the results of in scientific and objective ways. After computer simulation result that it is proved that compared with unpacked road condition and packed road condition. unpacked road condition is shorter than packed road condition.