• Journal of architectural history
• /
• v.14 no.1 s.41
• /
• pp.57-70
• /
• 2005

This study is the consideration about Hwaryeong-Jeon that enshrines Joseon Dynasty 22nd king Jeongjo's portrait of a king. Suwon's Hwaryeong-Jeon that accompanied a portrait and performed ritual ceremonies had several formalities and ceremonies which are connected with rituals. therefore, we will try to examine what relation between arrangement of building and plane composition had. And through this, it is thing to observe construction special quality that Hwaryeong-Jeon has. Joseon Dynasty's young-jeon (a hall where the royal portraits are kept) is retaining each other different state according to construction age every moment. Hwaryeong-Jeon among Joseon Dynasty's a hall of royal portraits is the construction form which is equiped well and is known for keeping the form well from the foundation to now And this building is evaluated as the standard form of early part young-jeon building of 19th century. Especially, Hwaryeong-Jeon shows the typical ritual equipments late Joseon Dynasty and at the same time has all kinds of characteristics which only we can find at Hwaryeong-Jeon. Namely, Hwaryeong-Jeon is the building which brings the design concept of the hall of royal portraits to completion as the building which enshrines single portrait of a king. After all, Hwaryeong-Jeon is evaluated as the building which can pass excellent form of late Joseon Dynasty, the hall of royal portraits building just as it is. Therefore, as I study its own style, I expect Joseon Dynasty's mind that enshrined the portrait of a king elaborately to be revealed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.130-134
• /
• 2008

This paper presents a clock and data recovery(CDR) using a quarter-rate technique. The proposed CDR helps reduce the VCO frequency and is thus advantageous for high speed application. It can achieve a low jitter operation and extend the pull-in range without a reference clock. The CDR consists of a quarter-rate bang-bang type phase detector(PD) quarter-rate frequency detector(QRFD), two charge pumps circuits(CPs), low pass filter(LPF) and a ring voltage controlled oscillator(VCO). The Proposed CDR has been fabricated in a standard $0.18{\mu}m$ 1P6M CMOS technology. It occupies an active area $1{\times}1mm^2$ and consumes 98 mW from a single 1.8 V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.8C
• /
• pp.806-815
• /
• 2006

It is studied to design a low pass filter of the SRC(sample rate converter), which is used to change the sampling rate of digital signals such as in digital modulation and demodulation systems. The larger the conversion ratio of the sample rate becomes, the more signal processing is needed for the filter, which corresponds to the more complexity in circuit realization. Thus it is important to reduce the amount of signal processing for the case of high conversion ratio. In this paper it is presented a design method of a two-stage cascaded FIR filter, which proved to have reduced amount of signal processing in comparison with a conventional single-stage one. The reduction effect of signal processing turned out to be more noticeable for larger value of conversion ratio, for instance, giving down to 72% in complexity for the conversion ratio of 32. It has been shown that the reduction effect is dependent to specific combination of conversion ratios of the cascaded filters. So an exhaustive search has been performed in order to obtain the optimal combination for various values of the total conversion ratio. In this paper every filter is considered to be implemented in the form of a polyphase FIR filter, and its coefficients are determined by use of the Parks-McCllelan algorithm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.1
• /
• pp.333-342
• /
• 2012

This paper presents a vowel onset point (VOP) detection method based on the human auditory system. This method maps the "perceptual" frequency scale, i.e. Mel scale onto a linear acoustic frequency, and then establishes a series of Triangular Mel-weighted Filter Bank simulate the function of band pass filtering in human ear. This nonlinear critical-band filter bank helps greatly reduce the data dimensionality, and eliminate the effect of harmonic waves to make the formants more prominent in the nonlinear spaced Mel spectrum. The sum of mel spectrum peaks energy is extracted as feature for each frame, and the instinct at which the energy amplitude starts rising sharply is detected as VOP, by convolving with Gabor window. For the single-word database which contains 12 vowels articulated with different kinds of consonants, the experimental results showed a good average detection rate of 72.73%, higher than other vowel detection methods based on short-time energy and zero-crossing rate.

• Journal of Digital Convergence
• /
• v.15 no.5
• /
• pp.235-240
• /
• 2017

Recently, Internet of things have been applied to various fields and are becoming common in our everyday life. Everything in our daily lives is networked, interacting with each other and giving us more useful effects. In this paper, we implemented an algorithm that can illuminate the LED lighting to the authorized person 's place in the network environment connected with the authentication device only once with the user authentication. User authentication in one building User authenticated through a single user search for the location of the user's lab stored in the database using the certified information and LED lights up to the lab where the user works. Through this, unnecessary energy is generated because people do not pass frequently.

• Journal of Korean Society of Steel Construction
• /
• v.12 no.2 s.45
• /
• pp.197-207
• /
• 2000

A transient heat transfer analysis and thermo-elastic analysis have been performed for the residual stress distribution on the fillet weldment used by finite element method. Specimen is fabricated single-pass fillet welding. This computation was performed for conditions including surface heat flux and temperature dependent thermo-physical properties using by heat input as parameter. Also, cut-off temperature of residual stress estimation by thermo-elastic analysis is determined. The fillet weldment were measured to determined their residual stress distributions for using hole-drilling method. As result, it was found that large tensile residual stress is about material yield strength, and the numerical simulation results for finite element method similar to residual stresses by hole-drilling method and other exiting research. Also, cut-off temperature is effectively determined by temperature which calculated maximum thermal stress equal to material yield strength.

• Journal of Korean Society of Water and Wastewater
• /
• v.29 no.1
• /
• pp.89-96
• /
• 2015

Smart water grid is a water network with communication to save water and energy using various water resources. In smart water grid, water product from the various sources can be blended to be supplied to end-users. The product water blending was reported by literatures while feed water blending has been rarely reported so far. In this work, a commercial reverse osmosis (RO) system design software provided by a membrane manufacturer was used to elucidate the effect of feed water blending on the performance of seawater reverse osmosis (SWRO) plant. Fresh water from exisiting water resource was assumed to be blended to seawater to decrease salt concentration of the RO feed water. The feed water blending can simplify the RO system from double to single pass and decrease seawater intake amount, the unit prices of the RO system components including high pressure pump, and operation risk. Due to the increase in RO plant capacity with the feed water blending, however, the RO membrane area and total power consumption increase at higher water blending rates. Therefore, a specific benefit-cost analysis should be carried out to apply the feed water blending to SWRO plants.

• Journal of Welding and Joining
• /
• v.25 no.3
• /
• pp.18-27
• /
• 2007

Laser welding process is widely used in the industrial field due to its numerous advantages: a small heat affected zone(HAZ), deep penetration, high welding speed, ease of automation, single-pass thick section capability, enhanced design flexibility, and small distortion after welding. The objective of this research works is to investigate the influence of the process parameters, such as the welding fur metals with CW Nd:YAG lasers. The bead-on-plate and Lap welding experiments are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the welding quality of the cross section, tensile stress behavior and the hardness of the welded part are investigated in comparison of the Nickel coated and Nickel uncoated S45C steel. As a result of experiment, nickel coated S45C Steel showed more even weld zone than Nickel uncoated counterpart upon lap welding. Also, it showed relatively small amount of internal defects and spatter, and Nickel coated S45C showed better weldability than Nickel uncoated S45C steel. The optimum welding process upon lap welding of Nickel coated S45C steel is when each laser power is 1900W; focal positions is -1mm; welding speed is $0.9{\sim}1.0m/min$. The heat input was $4.178{\sim}4.36{\times}103J/cm^2$.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.4
• /
• pp.246-252
• /
• 2000

Stellite 12 alloy-powder was overlaid on 410 stainless steel valve seat using plasma transferred arc(PTA) process. Variation of characteristic of microstructure and hardness of deposit with current(90~150 A) and preheat temperature(R.T.~$400^{\circ}C$) was investigated. Important conclusion obtained are as follows; All welding conditions used produced a sound deposit layer with no defect in single pass welding. The maximum deposit had 4.0~4.8 mm in thickness and its bead width was increased with increase of current and preheat temperature. The deposit showed hypoeutectic microstruture, which was consisting of primary cobalt dendrite and networked $M_7C_3$ type eutectic carbides. The amount of eutectic carbides was decreased and its dendritic secondary arm spacing was increased with increase of current. Hardness of the deposit was decreased with increase of current. Preheat temperature up to $400^{\circ}C$, however, showed little influence on the hardness and microstructure. The hardness was also influenced by diluted Fe content near the interface in addition to microstructure and dendritic secondary arm spacing. Hot hardness at $500^{\circ}C$ showed higher than 300 HV.

• Journal of the Korean housing association
• /
• v.28 no.2
• /
• pp.23-33
• /
• 2017

This study was aimed to assess accessibility situation of pedestrian environment of University-C focusing on accessibility of manual wheelchair users and to develop accessibility campus map. During March and April 2016, barrierfree design application situation of pedestrian environment and building entrances were investigated using a structured checklist and a digital distance and slope meter. Major findings are as follow. (1) Except one case, widths of all pedestrian routes (both sidewalk and non-sidewalk routes) exceeded 2 meters. (2) As for sidewalk and driveway contact point condition, there were many spots lacking curb ramp or alterative ramp that are accessible for manual wheelchair users. (3) More than half of non-sidewalk pedestrian routes did not have bollard to separate pedestrian and vehicle flows, and more than 92% of the bollards installed were too close for wheelchair users to pass or too far to prevent vehicle access. (4) More than 59 percent of the building entrances were found impossible for manual wheelchair users to access without any assistance, and one third of the buildings did not have any single accessible entrance. Based on the study findings, campus accessibility map was developed by the researchers and disseminated through university homepage. Using the campus accessibility map, users can plan their accessible paths ahead the trip.