• Journal of the Optical Society of Korea
• /
• 제10권1호
• /
• pp.1-10
• /
• 2006

Optical transparency and high diffraction efficiency are two essential factors for high performance of the photopolymer. Optical transparency mainly depends on the miscibility between polymer binder and photopolymerized polymer, while diffraction efficiency depends on the refractive index modulation between polymer binder and photopolymerized polymer. For most of organic materials, the large refractive index difference between two polymers accompanies large structural difference that leads to the poor miscibility and thus poor optical quality via light scattering. Therefore, it is difficult to design a high-performance photopolymer satisfying both requirements. In this work, first, we prepared a new phase-stable photopolymer (PMMA) with large refractive index modulation and investigated the optical properties. Our photopolymer is based on modified poly (methyl methacrylate) as a polymer binder, acryl amide as a photopolymerizable monomer, triethanolamine as initiator, and yellow eosin as a photosensitizer at 532 nm. Diffraction efficiency over 85% and optical transmittance over 90% were obtained for the photopolymer. Second, Organic-inorganic nanocomposite films were prepared by dispersing an aromatic methacrylic monomer and a photo- initiator in organic-inorganic hybrid sol-gel matrices. The film properties could be controlled by optimizing the content of an organically modified silica precursor (TSPEG) in the sol-gel matrices. The photopolymer film modified with the organic chain (TSPEG) showed high diffraction efficiency (> 90%) under an optimized condition. High diffraction efficiency could be ascribed to the fast diffusion and efficient polymerization of monomers under interference light to generate refractive index modulation. The TSPEG modified photopolymer film could be successfully used for holographic memory.

• Advances in nano research
• /
• 제4권3호
• /
• pp.181-195
• /
• 2016

Addition of nano-$SiO_2$ (NS) to geopolymer composites has been studied through measurement of compressive strengths, FTIR and XRD analysis. Alumino-silicate materials are coarse aggregate included waste concrete and demolished walls with its cementing binder, cement kiln dust (CKD) used and can possess a pronouncing activation for the geopolymer reaction resulting from the high alkali contents within. Materials prepared at water/binder ratios in a range of 0.30: 0.40 under curing of $40^{\circ}C$ and 100% Relative Humidity (R.H.), while the used activator is sodium hydroxide in the ratio of 2 wt. %. First, CKD is added in the ratio from 10 up to 50 wt., %, and the demolished walls was varied depending on the used CKD content, while using constant ratio of waste concrete (40 wt., %). Second step, depending on the optimum CKD ratio resulted from the first one (40 wt. %), so the control geopolymer mix composed of cement kiln dust, demolished walls and waste concrete in the ratio (40:20:40, wt %). Nano-silica partially replaced waste concrete by 1 up to 8%. Results indicated that, compressive strengths of geopolymer mixes incorporating nano-silica were obviously higher than those control one, especially at early ages and specially with 3%NS.

• 한국분말재료학회지
• /
• 제5권3호
• /
• pp.199-209
• /
• 1998

A new low melting inorganic binder, monoclinic $HBO_2$, has been developed for Selective Laser Sintering (SLS) of alumina powder by dehydration process of boron oxide powder in a vacuum oven at $120^{\circ}C$. It led to better green SLS parts and higher bend strength far green and fired parts compared to other inorganic binders such as aluminum and ammmonium phosphate. This appeared to be due to its low viscosity and better wettability of the alumina particle surface. A low density single phase ceramic, aluminum borate ($Al_{18}B_4O_{33}$), and multiphase ceramic composites, $A_{12}O_3-A_{14}B_2O_9$, were successfully developed by laser processing of alumina-monoclinic $HBO_2$ powder blends followed by post-thermal processing; both $Al_{18}B_4O_{33}$ and $A_{14}B_2O_9$ have whisker-like grains. The physical and mechanical properties of these SLS-processed ceramic parts were correlated to the materials and processing parameters. Further densification of the $A_{12}O_3-A_{14}B_2O_9$ ceramic composites was carried out by infiltration of colloidal silica, and chromic acid into these porous SLS parts followed by heat-treatment at high temperature ($1600^{\circ}C$). The densities obtained after infiltration and subsequent firing were between 75 and 80% of the theoretical densities. The bend strengths are between 15 and 33 MPa.

• 보존과학회지
• /
• 제36권5호
• /
• pp.339-350
• /
• 2020

본 연구는 석조문화재 보존처리용(표면마감) 무기질바인더가 암석에 위해한 영향을 미치는 백화현상을 제어하기 위해 광물기반의 충전제와 발수제를 혼합한 하이브리드 기술을 적용하였다. 연구결과, 무기질바인더 성능개선에 효과적인 충전제(실리카흄 3.4%)와 발수제(실란-실록산 1%)를 선정하였으며, 해당 중량비율은 백화물질 제어에 효과가 있는 것으로 판단된다. 또한 압축강도 기준을(20 MPa) 상회하였고 흡수율은 낮아 투수저항성이 높은 것을 확인하였다. 이온용출 결과도 백화현상에 직·간접적으로 작용하는 이온의 검출량이 대조군보다 작게 검출되어 상대적으로 안정적인 것으로 판단된다.

• 한국디지털건축인테리어학회논문집
• /
• 제12권3호
• /
• pp.59-66
• /
• 2012

Autoclaved Lightweight Concrete(ALC) features such as a high performance insulation, the fire resistance, the advantage of easy handing construction, and lightweight panels applied the curtain wall system. ALC materials are certified as non-toxic environmental and eco-friendly productions. But ALC external panels mixed with blast furnace slag pounder and silica fume have to be coated with a stucco compound or plaster because of resisting the ambient environment. This study is that mixing tests to evaluate a performance analysis of exterior paints to be make-up pigments(organic or inorganic) coated with panel surface. Testing compared by KS F 2476; flow test, KS F 2426; compression strength test, KS F 2762; bond strength test. In results, the case of the inorganic binder, ratio of alumina cement : anhydrite is 90:10 to 80:20 at the highest level of intensity. In the case of the organic binder, adhesive strength rating at surface of ALC, the pullout strength is below 0.5 $N/mm^2$ but the normal concrete is over 2.0$N/mm^2$. A contents ratio of EVA resin is more than 3% and then bond strength is effectively.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.386-391
• /
• 1998

Recently, high performance concrete developed has a good quality at fresh and hardened state, but high binder contents results in spending much money on manufacturing and many cracks by drying and autogenous shrinkage. Therefore, in this paper, not only prevention of cracks caused by drying and autogenous shrinkage, but improvement of quality and accmplishment of economy by applying F.A(fly ash), S.F(silica fume) and CSA(calcium sulfa aluminate) expansive additives as an inorganic admixtures in W/B 35% are discussed. According to the experimental results, when 5% of CSA Expansive additives and 15:5 (F.A:S.F)are replaced at unit cement content, high performance concrete with both good compensation of drying and autogenous shrinkage at hardened state is accomplished.

• Corrosion Science and Technology
• /
• 제14권5호
• /
• pp.213-217
• /
• 2015

Recently, household electronic industries require environmentally-friendly and highly functional steels in order to enhance the quality of human life. Customers especially require both excellent corrosion and abrasion resistant anti-fingerprint steels for digital TV panels. Thus POSCO has developed new functional electro-galvanized steels, which have double coated layers with organic-inorganic composites on the zinc surface of the steel for usage as the bottom chassis panel of TVs. The inorganic solution for the bottom layer consists of inorganic phosphate, magnesium, and zirconium compounds with a small amount of epoxy binder, and affords both improved adhesion properties by chemical conversion reactions and corrosion resistance due to a self-healing effect. The composite solution for the top layer was prepared by fine dispersion of organic-inorganic ingredients that consist of a urethane modified polyacrylate polymer, hardener, silica sol and a titanium complex inhibitor in aqueous media. Both composite solutions were coated on the steel surface by using a roll coater and then cured through an induction furnace in the electro-galvanizing line. New anti-fingerprint steel was evaluated for quality performance through such procedures as the salt spray test for corrosion resistance, tribological test for abrasion resistance, and conductivity test for surface electric conductance regarding to both types of polymer resin and coating weight of composite solution. New composite coated anti-fingerprint steels afford both better corrosion resistance and abrasion properties compared to conventional anti-fingerprint steel that mainly consists of acrylate polymers. Detailed discussions of both composite solutions and experimental results suggest that urethane modifications of acrylate polymers of composite solutions play a key role in enhanced quality performances.

• Korean Chemical Engineering Research
• /
• 제49권6호
• /
• pp.726-731
• /
• 2011

F-T 반응이 공업적으로 활용되기 위해서는 촉매의 대량 합성 및 성형체의 기계적 강도가 매우 중요한 변수로 적용될 수 있다. 따라서 본 논문에서는 F-T 합성반응용 촉매로 잘 알려진 Fe 계열 촉매의 성형체 제조를 위한 바인더의 영향을 알아보기 위한 연구를 수행하였다. 촉매 바인더로는 무기바인더와 유기바인더를 사용하여 촉매 성형체를 제조하였다. 무기바인더 및 유기바인더의 종류와 함량에 따른 성형촉매의 물리화학적 특성을 XRD, BET, PSD, TPR, UTM으로 분석하였으며, F-T 합성 반응성에 대한 영향을 관찰함으로써 최적의 성형 촉매 제조 조성을 확립할 수 있었다.

• 자원리싸이클링
• /
• 제17권4호
• /
• pp.30-36
• /
• 2008

본 연구에서는 하수슬러지 소각재를 원료로 사용한 다공성 경량재료의 제조 및 물성측정 실험을 수행하였다. 경량충진재로써 perlite와 silica sphere의 2종류 경량물질을 각각 사용하였으며, 무기바인더로써 벤토나이트를 첨가하여 $1,000^{\circ}C$에서 소성하는 방법으로 경량재료를 제조하였다. 제조한 시편은 밀도, 압축강도, 열전도도 및 흡음율을 측정하여 원료 조성 및 제조 조건에 따른 각각의 물성변화를 조사하였다. 실험결과 perlite를 경량충진재로 사용한 시편의 밀도는 $1.23{\sim}1.37g/cm^3$, 압축강도는 $242.3{\sim}370.5kg/cm^2$로 나타났으며, silica sphere를 사용한 경우는 perlite에 비해 밀도가 낮고 압축강도가 $100kg/cm^2$ 이하인 것으로 나타났다. 또한, 경량재료의 열전도도는 원료 조성에 따라 $0.3{\sim}0.5W/m^{\circ}K$의 수치를 보여 일반 콘크리트보다 단열효과가 매우 우수한 것으로 나타났다.

• 접착 및 계면
• /
• 제14권1호
• /
• pp.28-35
• /
• 2013

본 연구에서는 표면처리된 Ga-doped ZnO (GZO)를 사용해서 태양열 차단 코팅제를 제조하였으며, 표면처리 화합물의 종류와 처리조건에 따른 입자의 분산성, 가시광선투과율, 자외선차단율, 적외선차단율, 단열특성 등에 대해서 고찰하였다. IPA나 아크릴 바인더를 사용했을 때에는 무기산화물 입자의 분산특성이 낮았으나, 무기산화물 입자를 우레탄(우레아)기와 아크릴기 그리고 실리카를 포함하는 하이브리드 화합물로 표면처리한 경우에는 입자의 분산성이 향상되어 침전되는 입자가 거의 발생되지 않았고 가시광선 투과율과 헤이즈(haze)가 크게 향상되었다. 그리고 실제 단열특성을 평가하기 위해서 단열평가 장치와 sunlamp를 사용하였으며, 평가결과 열차단 필름을 사용한 경우 PET 필름 자체만 사용했을 때와 비교해서 내부온도가 $4.8^{\circ}C$ 이상 낮은 것으로 확인되었다.