• 제어로봇시스템학회:학술대회논문집
• /
• 1986.10a
• /
• pp.73-77
• /
• 1986

Optimal input design problem for linear regression model with constrained output variance has been considered. It is shown that the optimal input signal for the linear regression model can also be realized as an ARMA process. Monte-Carlo simulation results show that the optimal stochastic input leads to comparatively better estimation accuracy than white input signal.

• 전자공학회논문지 IE
• /
• v.44 no.2
• /
• pp.1-7
• /
• 2007

The increasing high frequency capabilities of CMOS have resulted in increased RF and analog design in CMOS. Design of RF and analog circuits depends critically on device S-parameter characteristics, magnitude of real and imaginary components and their behavior as a function of frequency. Utilization of scaled high performance CMOS technologies poses challenges as concerns for reliability degradation mechanisms increase. It is important to understand and quantify the effects of the reliability degradation mechanisms on the S-parameters and in turn on small signal model parameters. Various physical effects influencing small-signal parameters, especially the transconductance and capacitances and their degradation dependence, are discussed in detail. The measured S-parameters of H-gate and T-gate devices in a frequency range from 0.5GHz to 40GHz. All intrinsic and extrinsic parameters are extracted from S-parameters measurements at a single bias point in saturation. In this paper we discuss the analysis of the small signal equivalent circuits of RF SOI MOSFET's verificated for the purpose of exacting the change of parameter of small signal equivalent model followed by device flame.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.1
• /
• pp.95-102
• /
• 2020

The structural design of arch roofs or bridges requires the analysis of their unstable behaviors depending on certain parameters defined in the arch shape. Their maintenance should estimate the parameters from observed data. However, since the critical parameters exist in the equilibrium paths of the arch, and a small change in such the parameters causes a significant change in their behaviors. Thus, estimation to find the critical ones should be carried out using a global search algorithm. In this paper we study the parameter estimation for a shallow arch by a quantum-inspired evolution algorithm. A cost functional to estimate the system parameters included in the arch consists of the difference between the observed signal and the estimated signal of the arch system. The design variables are shape, external load and damping constant in the arch system. We provide theoretical and numerical examples for estimation of the parameters from both contaminated data and pure data.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.18 no.36
• /
• pp.253-263
• /
• 1995

In parameter design, Taguchi's stated objective is to find the setting of product or process design parameters that minimize average quadratic loss-that is, the average squared deviation of the response from its target value. Yet in practice to choose the settings of design parameters he maximizeds a set of measures called signal-to-noise(SN) ratios. In general, Taguchi gave no justification for the use the SN ratios and no explanation of why the two-step procedure that he recommened will minimize average loss. The purpose of this study is comparing and analyzing of performance statistics by Leon et al(PerMIA), Box(Transformation theory), Vining & Myers(Dual Response Systems) and Taguchi(Signal-to-Noise ratios).

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.2
• /
• pp.34-43
• /
• 2012

This paper describes system modeling and controller design method in the measured signal by discrete Fourier transform. Transfer function of the second order system is estimated by the dominant parameter which is computed in the magnitude and the phase of Fourier spectrum of the measured signal. In addition, the controller was designed by the estimated transfer function, and the results were compared. The proposed estimation method of transfer function contains only a very simple mathematical process. Therefore, it is effective to design the controller in the measured signal when the output of the system contains the characteristics of complex exponential functions case. The proposed method was applied on Op-Amp system to verify the efficiency and the reliability. The results show that the proposed algorithms are highly applicable to the system modeling and controller design in the measured data.

• Journal of information and communication convergence engineering
• /
• v.9 no.2
• /
• pp.220-223
• /
• 2011

Respiration signal of the vital signs is an important parameter in clinical parts. To extract the respiration signal from PPG signal for mobile healthcare system is difficult because the bands of the motion artifacts and respiration in the frequency domain are overlapped. This study to improve this problem suggested a respiration extraction method using the independent component analysis and evaluated its performances. In results of evaluation, the ICA method showed better performance than LPF suggested recently.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2078-2081
• /
• 1997

IP speed controller is used as a main controller and it makes the system low overshoot and easy controllability. Load torque is estimated by Kalman filter algorithm and parameter controller is used against a rotor inertia negative variations. Parameter Controller (PC) is equipped with a torque observer implemented by software of a digital signal Processor. PC is a parameter controller which selects a moment of inertia J in responding to a load torque to control the system response.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.11
• /
• pp.577-584
• /
• 2002

This paper presents a novel approach based on eigenvalue perturbation of augmented matrix(AMEP) to estimate the eigenvalue for variation of controller parameter. AMEP is a useful tool in the analysis and design of large scale power systems containing many different types of exciters, governors and stabilizers. Also, it can be used to find possible sources of instability and to determine the most sensitivity parameters for low frequency oscillation modes. This paper describes the application results of AMEP algorithm with respect to all controller parameter of KEPCO systems. Simulation results for interarea and local mode show that the proposed AMEP algorithm can be used for turning controller parameter, and verifying system data and linear model.

• Journal of the Korean Data and Information Science Society
• /
• v.20 no.5
• /
• pp.829-835
• /
• 2009

Parameter design is an approach to reducing performance variation of quality characteristic value in products and processes. Taguchi has used the signal-to-noise ratio to achieve the appropriate set of operating conditions where variability around target is low in the Taguchi parameter design. However, there are difficulties in practical application, such as complexity and nonlinear relationships among quality characteristics and control factors (design factors), and interactions occurred among control factors. Neural networks have a learning capability and model free characteristics. There characteristics support neural networks as a competitive tool in processing multivariable input-output implementation. In this paper we propose a substantially simpler optimization procedure for parameter design using neural network. An example is illustrated to compare the difference between the Taguchi method and neural network method.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.436-439
• /
• 2007

This paper describes the optimization of PGS(Patterned Ground Shield) of 5.5 turns rectangular spiral inductor using Taguchi's method. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. By using the taguchi's method, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.