• Geomechanics and Engineering
• /
• 제32권1호
• /
• pp.97-110
• /
• 2023

The coefficient of lateral earth pressure at rest in loose sand during virgin loading, K₀ , and during unloading, K'₀ , have been determined from laterally confined load-unload tests. The tests included measurement of lateral pressure with null pressure gauges, side wall friction with newly designed friction meters and applied pressure and base pressure with load cells. The importance of accounting for side-wall friction when evaluating the distribution of vertical pressure over the height of the soil specimen was demonstrated. Relatively uniform friction was observed during loading, but this was not the case during unloading unless friction reduction measures were employed. While the measured value of K₀ was found to be close to, if slightly higher than the value commonly estimated on the basis of friction angle, φ', the ratio of K'₀ to K₀ was found to reasonably fit an expression of the form K'₀/K₀ = 1 + C·log(OCR), with C equal to 1 in the present tests.

• 대한토목학회논문집
• /
• 제9권1호
• /
• pp.53-62
• /
• 1989

점변일차원이층류(漸變一次元二層流)모델로서의 염수(塩水)쐐기형상(形狀)의 계산(計算)을 행함에 있어서 필요(必要)한 계면저항계수(界面低抗係數)의 평가수단(評價手段)에 대(對)하여 논(論)한다. 예(例)를 들면, 폭(幅)이 좁은 실험수로(實驗水路)에서 얻어진 염수(塩水)쐐기의 형상(形狀)에 의해 계면저항계수(界面低抗係數)를 역산(逆算)하는 경우는 실제(實際)의 하천(河川)에서는 무시(無視)할 수 있는 수로(水路)의 측벽(側壁)의 영향(影響)을 보정(補正)하지 않으면 안된다. 본연구(本硏究)에서는 이러한 점(點)을 고려(考慮), 정상(定常) 염수(塩水)쐐기의 형상(形狀) 및 계면저항계수(界面低抗係數)에 미치는 수로(水路)의 측벽(側壁)의 영향(影響)을 밝힌다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.53-57
• /
• 1998

In order to investigate the effects of the variables during the stamping process upon the side wall curl behavior, experiments and finite element analyses were done using a 90 degree draw-bending test. The variables considered were the die radius, the forming speed, the restraint force, the lubrication and the sheet grade. The experiments and simulation conditions were selected according to the design of experiment (DOE) approach. The effects of the restraint force, the lubrication and the forming speed were the same for both high strength and mild steels, but the effects of the die radius on the side wall curl were dependent on the magnitude of the die radius and the sheet grade. A straight side wall was observed for both high strength and mild steels when the die radius was about 2∼3 times of the sheet thickness. It was recommended that the restraint force, the forming speed and the friction be increased in order to reduce the side wall curl.

• 한국군사과학기술학회지
• /
• 제3권2호
• /
• pp.213-218
• /
• 2000

An experimental study was performed to investigate the effect of surface temperature mismatch on measurements of skin friction using a plug-type skin friction gage mounted on the side wall of a supersonic wind tunnel. The freestream Mach number was 2.4 and Reynolds number per meter was $5.25 {\times}10^7$ with total pressure of 50 psi and total temperature of 275K. Temperature mismatch between the gage surface and surrounding wall surface was generated by hot water injection using the active temperature control system. Results of the tests showed that the temperature mismatch made sizable effects on the measurements of skin friction.

• 설비공학논문집
• /
• 제23권5호
• /
• pp.365-374
• /
• 2011

For the first time, the present study has measured the velocity distribution function in circular open channel flow in a three-dimensional shape using a stereoscopic PIV system. For a given channel slope, water depth was varied from 30% to 80% of the channel diameter. Then, the characteristics of the velocity distribution function was compared according to the change of the water depth. Unlike a rectangular channel, the present experiment exhibited quite different shapes in the velocity distribution function whether the water depth is higher than 50% or not. Especially, the position of maximum velocity in the central and side wall changes in a different manner for the water depth above 50%. By differentiating the velocity distribution function, local wall friction coefficient was evaluated as a function of wall position. If the water depth goes down, the difference between the maximum and minimum values in the local wall friction coefficient increases, and the averaged value a1so increases.

• 설비공학논문집
• /
• 제15권10호
• /
• pp.809-820
• /
• 2003

The present study investigates effects of flow velocity on the convective heat/mass transfer characteristics in wavy ducts of a primary surface heat exchanger application. Local heat/mass transfer coefficients on the wavy duct sidewall are determined by using a naphthalene sublimation technique. The flow visualization technique is used to understand the overall flow structures inside the duct. The aspect ratio and corrugation angle of the wavy duct is fixed at 7.3 and 145$^{\circ}$ respectively, and the Reynolds numbers, based on the duct hydraulic diameter, vary from 100 to 5,000. The results show that there exist complex secondary flows and transfer processes resulting in non-uniform distributions of the heat/mass transfer coefficients on the duct side walls. At low Re (Re<1000), relatively high heat/mass transfer regions like cell shape appear on both pressure and suction side wall due to the secondary vortex flows called Taylor-Gortler vortices perpendicular to the main flow direction. However, at high Re (Re>1000), these secondary flow cells disappear and boundary layer type flow characteristics are observed on pressure side wall and high heat/mass transfer region by the flow reattachment appears on the suction side wall. The average heat/mass transfer coefficients are higher than those of the smooth circular duct due to the secondary flows inside wavy duct. And also friction factors are about two times greater than those of the smooth circular duct.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권2호
• /
• pp.17-23
• /
• 2000

Experimental investigations were conducted to study the forced convection of fully-developed turbulent flow in horizontal equilateral duct fabricated with the same length and equivalent diameter, but different surface roughness pitch ratio(P/e) of 4, 8 and 16 on the one side wall only. The experiments were performed with the hydraulic diameter based Reynolds number ranged from 70,000 to 10,000. The entire bottom wall of the duct was heated uniformly and the other surfaces were thermally insulated. To understand the mechanisms of the heat transfer enhancement, measurements of the heat transfer were done to investigate the contributive factor of heat transfer promotion, namely, the fin effect. And the results were compared with those of previous investigations for similarly configured channels, at which they were roughened by regularly spaced transverse ribs in the rectangular and circular channels.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.65-70
• /
• 2000

Experimental investigations were conducted to study the forced convection of fully-developed turbulent f)on· in horizontal equilateral duct fabricated with the same length and equivalent diameter, but different surface roughness Pitch ratio(P/e) of 4, 8 and 16 on the one side wall only The experiments were performed with the hydraulic diameter based Reynolds number ranged from 70.000 to 10,000 The entire bottom wall of the duct was heated uniformly and the other surfaces were thermally insulated. To understand the mechanisms of the heat transfer enhancement. measurements of the heat transfer were done to investigate the contributive factor of heat transfer promotion. namely the fin effect. And the results were compared with those of Previous investigations for similarly configured channels, at which they were roughened by regularly spaced transverse ribs in the rectangular and circular channels.

• 한국지반공학회논문집
• /
• 제15권4호
• /
• pp.235-246
• /
• 1999

지하철 터널 등의 지하구조물을 개착식으로 시공할 때에는 먼저 지반을 굴착하고 구조물을 설치한 후에 굴착공간을 되메움한다. 이때 굴착면과 구조물사이의 되메움 공간이 협소하여 되메움지반의 자중에 의하여 지하구조물에 작용하는 토압은 고전적인 방법으로 구한 토압과 상이하다. 개착식으로 시공한 구조물의 상부슬래브와 측벽에 작용하는 연직 및 수평토압은 되메움공간의 형상에 따라 영향을 받을수 있으며 이를 규명하기 위하여 되메움공간의 형상과 벽마찰각을 변화시키면서 실내모형시험을 실시하여 그 결과를 기존의 토압이론과 비교분석하였다. 그 결과 되메움공간의 형상 즉 되메움폭과 원지반 굴착면 경사 및 구조물의 벽마찰각에 의한 영향이 관찰되었다.

• 대한기계학회논문집B
• /
• 제36권8호
• /
• pp.783-789
• /
• 2012

본 연구에서는 나선형 튜브내의 난류 열전달 및 하중 특성을 수치해석 방법을 이용하여 파악하였다. 열교환기와 같은 공학적 설비에서 관내 열전달을 향상시키기 위해 튜브의 형상을 나선형으로 설계한다. 이에 나선형 튜브내의 열전달 및 난류 특성에 대한 많은 실험적 연구가 이루어 졌으나, 대부분의 연구가 압력 강하 및 열전달 상관관계에 초점이 맞추어 진행되었다. 나선형 튜브내의 유동은 원심력에 의해 튜브 바깥쪽에서는 상대적으로 높은 열전달 및 전단응력이 발생하지만, 안쪽에서는 낮은 열전달 및 전단응력이 발생하게 된다. 따라서 본 연구에서는 튜브의 원주방향으로 발생하는 전단 응력 및 Nusselt 수의 변화를 Reynolds 수와 나선 코일의 지름을 변경하며 정량적으로 살펴보았다. 나선 코일 안쪽에서 국부적인 전단응력과 열전달율이 크게 낮게 특정되었으며, 이는 튜브 재질의 안정성에 영향을 미칠 것으로 판단되었다. 또한 본 연구에서는 마찰계수와 Nusselt 수에 대한 기존 상관관계식을 검증하였으며, 직관에서의 마찰계수와 Nusselt 수의 상관관계식이 나선형 튜브의 형상에도 적용될 수 있음을 관측하였다. 본 연구의 결과는 열교환기나 증기발생기의 안전성 평가를 위해 중요한 데이터로 활용될 수 있을 것이다.