• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.48-53
• /
• 2012

A non-linear vehicle model and an observer are designed to observe the yaw rate and the body side slip angle when a vehicle is turning maneuver in this study. The developed vehicle model is a full car model and has fourteen degree of freedom. A Luenberg observer is applied to develop the observer. The vehicle model is validated with a reference result and shows good accordance. The observer is tested on dry asphalt, wet asphalt and snow paved road. The results prove the performance of observer is robust and reliable.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.25 no.1
• /
• pp.14-19
• /
• 2023

In summer, the natural ventilation performance for varying greenhouse width is very important in the glasshouses for year round cultivation. The effect of the side openings and greenhouse width on natural ventilation performance was analyzed by simulation. The necessary ventilation rate with different solar radiation transmittance increased significantly when the outside temperature grows higher. The necessary ventilation rate of 40% transmittance was about half of that of 90% transmittance. In consequence, shading effect on temperature control in greenhouse is significant in summer. When the total area of the openings for ventilation is constant, the maximum ventilation rate happens when the area of roof openings is equal to the area of side openings. This maximum ventilation rate is about 3 times of that of the greenhouse with roof openings and without side openings. Therefore, the side openings are advantageous to improve the natural ventilation in greenhouses. As the greenhouse width increases, the influence of side openings on the ventilation rate is becoming smaller. If the natural ventilation rate of the greenhouse with roof and side openings is to become double of that of the roof openings only, the width should be narrower than 38.4m for the Venlo type and 64m for Wide span type.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1226-1231
• /
• 2009

This paper presents operating characteristics of internal heat exchanger(IHX) for $CO_2$ geothermal heat pump in the heating mode. Mass flow rate of $CO_2$, inlet temperatures of $CO_2$ at high and low pressure side were selected as main effect factors by using fractional factorial DOE(Design of Experiments). And RSM(Response Surface Method) was used in optimization phase. The results show that heat transfer rate of IHX increases when either inlet temperature of low pressure side decreases or inlet temperature of high pressure side increases. Effectiveness of IHX increases with increasing of inlet temperature of either high pressure side or low pressure side. Finally, performance contour map was provided over the operation ranges of the main design factors.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.405-410
• /
• 1996

New methodology for mass and energy release assessment in LBLOCA post blowdown is needed and, first of all, the phenomenologically improved and quantitative assessments through experiment are essential. For tile experiment of a hot leg break LBLOCA in post blowdown, the test facility was set and its feature is that tile broken hot leg has two broken sections in the tore side and in the SG side respectively and a separation valve between the two in order to measure the release rate dividedly. Specially it was focused on whether the mass release through the SG side broken section happened or not. The mass release through the core side broken section is dependent on tile safety injection flow and that through the SG side broken section varies depending on several factors. The principal factor is the primary system pressure and the subfactors such as SI flow rate, SI temperature and initial primary pressure, may contribute, too.

• Journal of the Korea Construction Safety Engineering Association
• /
• s.41
• /
• pp.80-87
• /
• 2007

The purpose of this paper is to investigate the removal efficiency of fine dusts as the configuration condition of machinery and equipments in Clean Room and to analyze the flowing behaviors of fine dusts as the layout of Clean Room. The layout of the Clean Room was classified into side layout type, 2 center line type and center concentration type layout, and the flow rates used in this research were 0.22m/s, 0.44m/s and0.80m/s. Dust removal efficiency as layout change was decreased 37% for side layout type, 31% for 2 centerline type and 20% for center concentration type layout at the flow rate of 0.22m/s, compared with the state without machinery and equipments in Clean Room. The efficiency was decreased 42% for side layout type,22% for 2 center line type and 8% for center concentration type layout at the flow rate of 0.44m/s, and decreased 20% for side layout type, 18% for 2 center line type and 10% for center concentration type layout at the flow rate of 0.80m/s. According to the result of dust removal behavior, $0.3\mum$, $1\mum$and $3\mum$dust except for $5\mum$showed the higher change of the behavior in side layout type than in center concentration type layout due to the change of air flow. It was confirmed that removal behavior depends on the layout of machinery and equipments as the dust size decreases.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.101-105
• /
• 1998

This paper describes anisotropic etching technology of highly doped polysilicon. The main etching gases are $Cl_2$ and $SiCl_4$ for reactive ion etching of polysilicon. The mixed $CHCl_3$ to main etching gas makes polymer on etching side wall, so it prevents side etching of polysilicon. The etch rate of polysilicon is increased with increasing RF power. But the etching rate is decreased as the flow rate of $CHCl_3$ is increased with fixed RF power. The etch selectivity of polysilicon and $SiO_2$ is about 12:1. And that of polysilicon and $Si_3N_4$ is about 19:1. In the main etching gas condition, the slope of polysilicon is same as that of photoresist. But in the mixed $CHCl_3$ condition, the slope of polysilicon is larger than that of photoresist. This represents that the polymer made on side wall by added $CHCl_3$ prevents side etching, so anisotropic etching can be possible by polymer.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.11
• /
• pp.181-188
• /
• 2019

The purpose of this study is to evaluate the cooling energy saving effects of CRAH supply air temperature(SAT) and design flow rate changes when applying air-side economizer in the data center. MLC(Mechanical Load Component), which is cooling performance indicator of data center, was used to assess the effectiveness of cooling energy savings. It was computed with energy simulation (DesignBuilder) to evaluate the cooling energy performance of 8 different alternatives in a data center. The MLC was 0.31~0.32 regardless of CRAH supply temperature without air-side economizer, and 0.15 to 0.19 value with air-side economizer. That is, cooling energy can be reduced by approximately 40~55% when applying economizer. As the CRAH SAT and design flow rate changed, the MLC values were 0.16 to 0.18 and 0.15 to 0.19, respectively.

• Journal of The Geomorphological Association of Korea
• /
• v.24 no.2
• /
• pp.27-40
• /
• 2017

This study tries to analyze topographic distribution and characteristics of as well as formative age and incision rate of fluvial terraces in Danyang River on western side and Geum River on eastern side of the northern Sobaek Mountains and to estimate geomorphic development during the late Quaternary in the mountains regarded as one of the uplift axes in the Korean Peninsula. OSL age dating shows that the fluvial terrace I with an altitude above riverbed of approximately 7~13 m in Danyang River has a formative age of approximately 18 ka (MIS 2) and incision rate in the river is approximately 0.156~0.194 m/ka based on the age. Altitudes above riverbed of the fluvial terrace I in Geum River range from approximately 7 to 14 m and the terrace is thought to be older than 70 ka based on age result from aeolian sediments above the terrace deposits, suggestive of an incision rate less than approximately 0.10 m/ka. These results indicate lower uplift rate in the northern Sobaek Mountains than in the Taebaek Mountains. Moreover, it can be suggested that the northern Sobaek Mountains has experienced asymmetric uplift during the late Quaternary, because the river on western side of the northern Sobaek Mountains shows greater uplift rate than the eastern side river does. Low incision rate in Geum River can be attributed to low altitude of the river basin with little difference in altitude from the base level as well as to gentle river slope due to influence of Nakdong River.

• Ocean and Polar Research
• /
• v.24 no.3
• /
• pp.227-236
• /
• 2002

For ten firn cores, from both the eastern and the western side of Lambert Glacier basin (LGB), snow accumulation rate and isotopic temperature were measured far the recent 50 years. Results show that snow accumulation for five cores over the eastern side of LGB (GC30, GD03, GD15, DT001, and DT085) at Wilks Land and Princess Elizabeth Land increases, whereas it decreases at the western side (Core E, DML05, W200, LGB 16, and MGA) at Dronning Maud Land, Mizuho Plateau and Kamp Land. For the past decades, the increasing rate was $0.34-2.36kg\;m^{-2}a^{-1}$ at the eastern side and the decreasing rate was $-0.01\;-\;-2.36kg\;m^{-2}\;a^{-1}$ at the western side. Temperatures at the eastern LGB were also increased with the rate of $0.02%o\;a^{-l}$. At the western LGB it was difficult to see clear trends, which were confirmed by Instrumental temperature records at coastal stations. Although statistic analysis and modeling results display that both surface temperature and accumulation rate has increased trends in Antarctic ice sheet during 1950-2000, the regional distributions were much more different for different geographic areas. We believe that ice-core records at Wilks Land and Princess Elizabeth Land reflect the real variations of SST and moisture change in the southern India Ocean. For the Kamp Land and Dronning Maud Land, however circulation pattern was different, by which the climate was more complicated. The International Trans-Antarctic Scientific Expedition (ITASE) aimed to reveal an overall spatial pattern of climate change over Antarctic ice sheet for the past 200 years. This study points the importance of continental to regional circulation to annual-decadal scale climate change in Antarctica.

• The Journal of the Korean dental association
• /
• v.12 no.2
• /
• pp.107-111
• /
• 1974

In order to collect some necessary data to promote correcting the toothbrushing technic on the Korean public, the author had examined the number of present teeth on which had cervical abrasion and the most basic home dental care in 2,000 Korean male and female adults from 19 to 52 years in the age. Then, the cervical abrasion experience rate and the cervical abrasion experience teeth rate were calculated and evaluated. The obtained results were as follows: 1. Cervical abrasion experience rate was 32.45% 2. Cervical abrasion experience rate was gradually increased by ageing. 3. Cervical abrasion experience rate in male adults was higher than that in female adults. 4. Cervical abrasion experience rate in the lower jaw was higher than that in the upper jaw. 5. Cervical abrasion experience rate of the teeth at the right side was higher than that of the teeth at the left side. 6. Cervical abrasion experience teeth rate was 3.82%. 7. Cervical abrasion experience rate was highest on the first bicuspid, and followed in the sequence of the second bicuspid, canine, first molar, incisors, and 2nd and 3rd molars.