• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.5
• /
• pp.1310-1321
• /
• 1994

Turbulent coherent structures in the intermediate wake of a stationary and rotating cylinder, spin rate S=0.7, situated in a uniform were experimentally investigated using a conditionalphase average technique. Measurements were carried out at a section of 8.5 diameters downstream form the center of cylinder and a Reynolds number of $Re=6.5{\times}10^{3}.$/TEX> The phase averaged velocity and velocity vector fields, contours of vorticity, turbulent intermittency function and velocity fluctuation energy are presented and discussed in relation to the large scale coherent structures by Karman vortices that shed periodically from the cylinder. Coherent wake structures of the rotating cylinder is almost identical with stationary cylinder, but the lateral displacement and shrinkage of turbulent wake region is occured by rotation. Rotation of the cylinder result in that the deflection of wake center to deceleration region(Y/D${\simeq}-0.3)$ and the decrease of mean velocity defect(10%), vorticity strength of large scale structures(19%), total velocity fluctuation energy(12%).

• Journal of Sensor Science and Technology
• /
• v.32 no.3
• /
• pp.159-163
• /
• 2023

Salt cores have attracted considerable attention for their application to the casting process of electric vehicle parts as a solution to ecological issues. However, the salt core still has low mechanical strength for use in high-pressure die casting. In this study, we investigated the improvements in the bending strength of KCl-based salt cores resulting from the use of reinforcing materials. KCl and Na₂CO₃ powders were used as matrix materials, and glass fiber and carbon fiber were used as reinforcing materials. The effects of carbon fiber and glass fiber contents on the bending strength properties were investigated. Here, we obtained a new fiber-reinforced salt core composition with improved bending strength for high-pressure die casting by adding a relatively small amount of glass fiber (0.3 wt%). The reinforced salt core indicates the improved properties, including a bending strength of 49.3 Mpa, linear shrinkage of 1.5%, water solubility rate of 16.25 g/min·m² in distilled water, and hygroscopic rate of 0.058%.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.87-90
• /
• 2008

Since fastener bolt for airplane require high specific strength and corrosion resistance, Ti-6Al-4V alloy is widely used. However, the Ti-6Al-4V bolt is generally manufactured by cutting and rolling because of their poor workability. The aim of present work is to develop hot forming technology for high strength Ti-6Al-4V. Various heat-treatments were applied to specimen in order to increase hot-workability and prevent galling with die Multiple forging were simulated with FE code to determine optimum process parameters including specimen temperature, strain rate, local strain, and thermal shrinkage. Forged samples were heat-treated again to increase their mechanical properties.

• Journal of the Korea Furniture Society
• /
• v.24 no.1
• /
• pp.79-87
• /
• 2013

The objective of this study was to increase the utilizability of domestic thinning and small diameter wood as applying in pattern design which can be applied in interior decoration, wood craft and wood furniture, and in developing the designs of furniture and household items. Then we investigated the physical and mechanical characteristics of Acer mono wood by pressurization and heat treatment. Color change is clear, and the wood density is increased with increasing pressing rate. The compressive and bending strengths are decreased as heating time is increased after pressing. However, shrinkage is improved after pressing and heating.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.49-54
• /
• 2020

The purpose of this study is to investigate the effects of the change in the spindle speed and the feed rate on the diameter change of a hole using a boring cutter for the internal boring process of AL6061-T4 alloys. The experimental results are quantitatively analyzed by applying the factor analysis and the response surface analysis of the experimental design method. The tendency of the diameter change according to the change in the spindle speed and feed level is also evaluated. During the internal boring process of AL6061-T4 alloys, the main factor affecting the diameter change is the spindle speed in which the diameter decreases as the number of revolutions increases. In addition, the diameter tends to increase as the feed is increased; however, as the number of spindle revolutions increases, the influence of the feed decreases.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1999.10a
• /
• pp.175-178
• /
• 1999

In most domestic construction fields, excessive cement content has been used because of stubborn official inspection. The purpose of this study is to reduce the cement content of mix proportioning for the decrease of hydration heat, brittleness and drying shrinkage which governs durability of concrete significantly. Parameters includes the compressive strengths, type and dosage rate of chemical and mineral admixtures and types of concrete. It is found that the chemical admixture is efficient to the reduction of cement content for high strength concrete (400kg/$\textrm{cm}^2$) and the effectiveness of mineral admixtures in the low strength concrete is somewhat higher than the high strength concrete.

• Journal of the Korean Ceramic Society
• /
• v.40 no.5
• /
• pp.410-414
• /
• 2003

Characteristics of $UO_{2+x}$ powders oxidized at different temperatures were examined. Pellets were fabricated by adding these oxidation powders and their properties were also investigated. Particle size of the $UO_{2+x}$ powders decreased with increasing oxidation temperature while surface area increased. Only the powders oxidized at 35$0^{\circ}C$ enhanced the strength of green pellet. However, 35$0^{\circ}C$ oxidized powders added pellet had many surface defects. The difference of shrinkage rate between the oxidized and UO$_2$ powders was thought to be the cause of them.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.2
• /
• pp.8-15
• /
• 1990

This study was carried out to investigate the wood qualities for the end-use development of sycamore (Platanus occidentalis L.) grown in Korea. The results obtained were as follows: 1. The average length of wood fibers was l.56mm and the average width of annual rings was 9.5mm. It had very fast growth rate. 2. The specific gravity in air-dry was 0.66. The shrinkage and water absorption were relatively large. The shear and impact strengthes were very strong, while the compressive, tensile, and bending strengthes were weak in comparison to it's specific gravity. 3. The contents of ash, holocellulose, lignin were relatively high 0.74%, 83.08%, 28.79%, but that of pentosan was low 18.53%. 4. The expected uses of sycamore wood are plywood. fancy veneer, small furniture, musical instrument, door and window frame, tool handels, boxes, etc.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1389-1393
• /
• 2007

Selective Laser Sintering (SLS) is currently recognized as a leading process in the new field of solid freeform fabrication (SFF). It is used to fabricate in a short time any 3 dimensional shapes by layer-by-layer sintering of polymer, ceramic or metal powder. To develop this SFF system, it needs effective laser scanning path, temperature and z-axis control for lamination. Therefore, in this study, through the application of control algorithm for sintering process have performed, temperature evaluation for sintering process has performed and the manufacturing sample using SLS process.

• Journal of the Korean Ceramic Society
• /
• v.31 no.6
• /
• pp.660-670
• /
• 1994

Transparent, crack-free dried gel monoliths with a composition of LiZr1.5Si2P2O12.5 have been synthesized by the low temperature polymerization of the Sol-Gel technique using metal alkoxides as starting materials. After initial reaction (20~40 min), each metal alkoxide closely paralleled each other during the hydrolysis reactions. The safe drying conditions of gels with no creaks the control of the shrinkage rate. The gels converted into the glass by heat treatment at 75$0^{\circ}C$. FTIR data indicated that the gels were phase separated into silicarich and phosphate-rich regions with the lithium. XRD results showed the formation of crystalline LiH2PO4. The gels dried at 15$0^{\circ}C$ or fired at 75$0^{\circ}C$ contained the residual water. The high ionic conductivity at room temperature for these gels was attributed to the motion of protons.