• Fashion & Textile Research Journal
• /
• v.1 no.3
• /
• pp.275-279
• /
• 1999

The purpose of this study was to investigate a specific character on products of Korean cotton and American cotton with cultivated in sangju city, Korea. The results of this study were as follows: Productivity of American cotton was nine times higher than those of Korean cotton. Spinning coefficient index (SCI: 140), strength (32.6 g/tex), fiber length (1.12 inch), uniformity index (83.4%), short fiber index (6.4), color grade (21) of American cotton was superior than SCI (122), strength (27.7 g/tex), fiber length (1.02 inch), uniformity index(81.1 %), short fiber index (10.6), color grade (23) of Korean cotton. Microaire (3.5), elongation (6.9%) of Korean cotton was superior than American cotton.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.5
• /
• pp.14-20
• /
• 2012

In this paper, the flame-retardant wall paper was successfully prepared with recycled polyethylene terephthalate (PET) short cut fiber with flame-retardant property and wood pulp using polyvinyl alcohol (PVA) as binder followed by treatment of non-halogen flame retardant. Physical properties such as formation index, tensile strength, elongation, and burst strength increased as defibrillation increased except tear strength. Bulk increased but formation index, tensile strength, elongation and burst strength decreased along with addition of PET short cut fiber. It was also found that tear strength rose significantly up to 30% of PET short cut fiber and then declined (fell) rapidly. As addition level of PVA increased tensile strength, elongation and burst strength increased, but tear strength decreased slightly. Addition of 20% of PET short cut fiber and 13% of PVA provided the flame-retardant wall paper with both improved flameproofing and physical properties.

• ETRI Journal
• /
• v.6 no.4
• /
• pp.3-8
• /
• 1984

Frequency division multiplexed 3ch. Color TV signals have been transmitted via optical fiber by employing $1. 3\mum$ InGaAsP DH-laser diode, graded index optical fiber and Ge-APD as optical components. Overall system margin of 20 dB was realized at weighted SNR of more than 49 dB. With this system margin, measured DG and DP were less than 10% and $5^{\circ}$respectively. Throughout this experiment, it was confirmed that multichannel TV signals could be economically transmitted over optical fiber in short haul networks. This paper describes system outlines and hardware implementation results.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.3
• /
• pp.58-65
• /
• 1997

This research was carried out to evaluate the effect of process variables on mechanical properties of the wood fiber-thermoplastic fiber composites by turbulent air mixing method. The turbulent air mixer used in this experiment was specially designed in order to mix wood fiber and thermoplastic polypropylene or nylon 6 fiber, and was highly efficient in the mixing of relatively short plastic fiber and wood fiber in a short time without any trouble. The adequate hot - pressing temperature and time in our experimental condition were $190^{\circ}C$ and 9 minutes in 90% wood fiber - 10% polypropylene fiber composite and $220^{\circ}C$ and 9 minutes in 90% wood fiber 10% nylon 6 fiber composite. Both in the wood fiber - polypropylene fiber composite and wood fiber- nylon 6 fiber composite, the mechanical properties improved with the increase of density. Statistically, the density of composite appeared to function as the most significant factor in mechanical properties. Within the 5~15% composition ratios of polypropylene or nylon 6 fiber to wood fiber, the composition ratio showed no significant effect on the mechanical properties. Bending and tensile strength of composite, however, slightly increased with the increase of synthetic fiber content. The increase of mat moisture content showed no significant improvement of mechanical properties both in wood fiber - polypropylene fiber composite and wood fiber nylon 6 fiber composite. Wood fiber - nylon 6 fiber composite was superior in th mechanical strength to wood fiber-polypropylene fiber composite, which may be related to higher melt flow index of nylon 6 fiber(22g/10min) than of polypropylene fiber(4.3g/10min).

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.981-982
• /
• 1998

We fabricated sampled fiber grating by double-exposure method. First, a short-period grating was written into the hydrogen-loaded single mode fiber and then the refractive index was modulated over it by an amplitude mask. It was observed that several transmission dips appear due to the index modulation. The thermal and strain responses were measured over $40-180^{\circ}C$ and $0-1800\mu\varepsilon,$ respectively. The dips have the same and linear sensitivity to both physical quantities over the range of measurement.

• Current Optics and Photonics
• /
• v.5 no.6
• /
• pp.652-659
• /
• 2021

The theoretical analysis and optimization of extrinsic Fabry-Perot interferometer (EFPI) opticalfiber humidity sensors are deeply investigated. For a typical dual-cavity structure composed of an optical fiber and a humidity-sensitive membrane (HSM), the changes in refractive index (RI) and initial length are discussed for polymer materials and porous oxide materials when relative humidity (RH) increases. The typical interference spectrum is simulated at different RH using MATLAB. The spectral change caused by changing HSM RI and initial length are simulated simutineously, showing different influences on humidity response. To deeply investigate the influence on RH sensitivity, the typical response sensitivity curves for different HSM lengths and air-cavity lengths are simulated. The results show that the HSM is the vital factor. Short HSM length can improve the sensitivity, but for HSM RI and length the influences on sensitivity are opposite, because of the opposite spectral-shift trend. Deep discussion and an optimization method are provided to solve this problem. According to analysis, an opaque HSM is helpful to improve sensitivity. Furthermore, if using an opaque HSM, a short air cavity and long HSM length can improve the sensor's sensitivity These results provide deep understanding and some ideas for designing and optimizing highly sensitive EFPI fiber humidity sensors.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.5 s.118
• /
• pp.9-15
• /
• 2006

Wet compaction test (WCT) is a fiber evaluation method where wet fibers are compressed at one side of a cylinder and water drains out from the other side. The consistency of the fiber furnishes and their pressures are recorded during the test. In the previous study we found that WCT results always gave better coefficients of determination in fiber furnish drainage, and paper properties (density, tensile, tear, and burst strength) than those of WRV (water retention value). Fiber freeness and fiber length correlated well with drainage and tear strength of the furnishes, respectively; however, their correlations were very much improved by combining the WCT results. In this study, we used the WCT test for fractionated fiber furnishes to see whether improvement of the WCT is possible. We found that strength properties such as breaking length and burst index were correlated better with the fractionated long fiber furnishes. Drainage was greatly affected by the presence of short fiber furnishes. We used bleached chemical pulps (SwBKP, HwBKP), recycled pulp (OCC), and mechanical pulp (BCTMP) as fiber furnishes in this study. Fiber fractionation can be performed on-line in these days by using multifractor and WCT can be used as an on-line test in papermachine in the future.

• Advances in nano research
• /
• v.14 no.6
• /
• pp.557-573
• /
• 2023

The rapid growth of zinc-oxide (ZnO) nanostructures (NSs) on woven carbon fiber (WCF) is reported in this study employing a microwave-aided chemical bath deposition process. The effects of different process parameters such as molar concentration, microwave duration and microwave power on morphologies and growth rate of the ZnO on WCF were studied. Furthermore, an attempt has been taken to study influence of different type of growth solutions on ZnO morphologies and growth rates. The surface functionalization of WCF fabrics is achieved by successful growth of crystalline ZnO on fiber surface in a very short duration through one-step microwave synthesis. The morphological, structural and compositional studies of ZnO-modified WCF are evaluated using field-emission scanning electron microscopy, X-ray diffraction and energy dispersive X-ray spectroscopy respectively. Good amount of zinc and oxygen has been seen in the surface of WCF. The presence of the wurtzite phase of ZnO having crystallite size 30-40 nm calculated using the Debye Scherrer method enhances the surface characteristics of WCF fabrics. The UV-VIS spectroscopy is used to investigate optical properties of ZnO-modified WCF samples by absorbance, transmittance and reflectance spectra. The variation of different parameters such as dielectric constants, optical conductivity, refractive index and extinction coefficient are examined that revealed the enhancement of optical characteristics of carbon fiber for wide applications in optoelectronic devices, carbon fiber composites and photonics.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.8 no.4
• /
• pp.164-171
• /
• 1983

In this paper, angular division multiplexing of the optical multiplexing technique for transmitting several channels using a relatively short step-index fiber is described. Mode coupling and the output power distributionin the fiber for the plane wave excitations is calculated and the crosstalk level determination of the system is proposed. In the presence of the mode coupling, the pulse width in terms of the fiber's length and input condition is calculated in the slab waveguide and the fiber. For the input angles (

• Journal of the Optical Society of Korea
• /
• v.12 no.3
• /
• pp.126-130
• /
• 2008

We propose and experimentally demonstrate an effective method to reduce near-field speckle noise at the output of a 50 ${\mu}m$ graded index multimode fiber using a short cylindrical piezoelectric transducer(PZT) vibrating in the radial direction. The fiber was coiled as tightly as possible around the mandrel of the PZT and a periodic stretching effect was caused by the radial oscillations of the actuator. The output of the optical fiber using the He-Ne laser source was intensively observed by a CCD camera. By counting all the pixels corresponding to relative intensity graded into 256 levels in the selected area and by calculating standard deviation and mean value of the intensity, we could measure the speckle contrast and vibration effect quantitatively with reduction ratio of pixels and line profile of the illuminated region. It was clearly observed that the characteristics of the speckle pattern in the vibration-on state were significantly improved over that of the vibration-off state due to time-averaged smoothing.