• Archives of Reconstructive Microsurgery
• /
• 제20권1호
• /
• pp.26-31
• /
• 2011

Purpose: We compared wound healing between the conventional tie-over dressing and silicone sheeting after skin grafting in patients with skin defects. Materials and Methods: Of a total of 30 cases of skin defects, 15 underwent conventional tie-over dressing and the remaining 15 underwent silicone sheeting skin grafting, we compared hematoma formation and infection status between the 2 techniques 1 and 2 weeks after operation Results: Hematoma was not observed in all cases. The wound infection rate decreased in silicone group. Conclusions: Silicone sheeting skin graft may be helpful in reducing wound infection.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1801-1817
• /
• 2018

This paper presents the numerical parametric analysis on the loading capacity of Channel purlins with screw-fastened sheeting, in which the effects of anti-sag bar and corrugated steel sheet on the ultimate capacity are studied. Results show that the setup of anti-sag bars can reduce the deformations and improve the ultimate capacity of C purlins. The traditional method of setting the anti-sag bars in the middle of the web is favorable. The changing of sheeting type, sheeting thickness and rib spacing has significant effects on the ultimate capacity of C purlins without anti-sag bars, compared with those with anti-sag bars. The proposed design formulas are relatively consistent with the calculations of EN 1993-1-3:2006, which is different from those of GB 50018-2002.

• Steel and Composite Structures
• /
• 제15권4호
• /
• pp.425-438
• /
• 2013

A new-styrofoam-concrete composite sandwich slab with function of heat insulation is designed. Four full-scale simply supported composite sandwich slabs with different shear connectors are tested. Parameters under study are the thickness of the concrete, the height of profiled steel sheeting, the influence of shear connectors including the steel bars and self-drilling screws. Experimental results showing that four specimens mainly failed in bending failure mode; the shear connectors can limit the longitudinal slippery between the steel profiled sheeting and the concrete effectively and thus guarantee the good composite action and cooperative behavior of two materials. The ultimate sagging bending resistance can be determined based on plastic theory. This new composite sandwich slab has high sagging bending resistance and good ductility. Additionally, these test results help the design and application of this new type of composite sandwich slab.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.12-13
• /
• 2021

As construction projects are gradually getting larger and focusing on building skyscraper with the development of construction technology and the concentration of population in cities, the choice of the soil sheeting works is very important in terms of securing safety and economic feasibility. Further research is planned on the developed concrete guide-based continuous over lap pile method through the introduction of a system that automates vertical management, continuous improvement and supplementation so that the basement soil sheeting wall can be utilized as a building structure.

• Archives of Plastic Surgery
• /
• 제33권6호
• /
• pp.700-705
• /
• 2006

Purpose: For hypertrophic scars and keloids no universally effective treatment modality exists. Surgical revision, intralesional steroid injection, silicone gel sheeting, pressure, laser, and others have been used with variable success, but many treatments are associated with high recurrence rates. Although optimal treatment remains undefined, successful treatment can be obtained through a combined therapeutic approach. Methods: We used three therapeutic modalities in combination, which are intralesional injection of triamcinolone acetonide, silicone gel sheeting, and 585 nm flashlamp-pumped pulsed dye laser. Fifty-eight cases of hypertrophic or keloid scar were treated by combined therapeutic regimen for mean period of 18 months. The changes of thickness, color, and pliability of scars were evaluated with clinical photographs by grading scale. Results: As summing the grades and categorizing the result into three group, we obtained 28% good, 67% fair, and 5% poor results. There was a desirable improvement of scars with insignificant adverse effects. Conclusion: Combination of intralesional steroid injection, silicone gel sheeting, and pulsed dye laser can lead to successful treatment of hypertrophic scar and keloid.

• Steel and Composite Structures
• /
• 제42권1호
• /
• pp.33-48
• /
• 2022

This paper researches a lightweight composite structure referred to as the Profiled Steel Sheeting Dry Board (PSSDB). It is fundamentally produced by connecting a Profiled Steel Sheeting to Dry Board using mechanical screws. It is mainly employed as floor panels. However, almost all studies have focused on researching the one-way structural performance. Therefore, this study focuses on the bending behaviour of the two-way PSSDB floor system using both of Finite Element (FE) and Experimental analysis. Four panels were used in the experimental tests, and a mild steel plate has been applied at the bottom for two panels. For the FE process, models were created using ABAQUS software. 4 parametric studies have been utilized to understand the system's influential elements. From the experimental tests, it was found that using Steel Plate shall optimize the two-way action of the system and depending on the type of dry board the improvement in stiffness may reach up to 38%. It was shown from the FE analysis that the dry board, profiled steel sheeting and steel plat can affect the system by up to 10 %, 17% and 3% respectively, while applying a uniform load demonstrate a better two-way action.

• 한국강구조학회 논문집
• /
• 제11권2호통권39호
• /
• pp.143-151
• /
• 1999

본 논문에서는 냉간성형 profiled steel sheeting과 보통강도의 콘크리트로 이루어진 합성보의 휨거동에 관한 연구를 통하여 새로운 형식의 보부재의 사용가능성을 검토하였다. 합성보의 비선형거동을 추적하기 위하여 profiled steel sheeting, 철근 및 콘크리트의 재료비선형을 포함할 수 있는 해석적 방법을 개발하였으며, 합성보의 비선형 모멘트-곡률 관계를 나타낼 수 있는 Power Model식을 제시하였다. Power Model은 원래 보-기둥 접합부의 모멘트-회전각과의 관계를 예측하기 위해 제안된 것이나 합성보에 맞게 수정하였다. 합성보의 하중-처짐 거동은 Power Model에 의한 모멘트-곡률 관계를 이용하여 변위조절법인 단계별 수치적분법을 적용하여 계산하였으며, 실험결과와 비교하였다.

• Wind and Structures
• /
• 제32권1호
• /
• pp.55-69
• /
• 2021

Ultrapure ferritic stainless steel provides a new generation of long-span metal roof systems with continuous welding technology, which exhibits many unknown behaviors during wind excitation. This study focuses on the wind-resistant capacity of a new continuous welding stainless steel roof (CWSSR) system. Full-scale testing on the welding joints and the CWSSR system is performed under uniaxial tension and static ultimate wind uplift loadings, respectively. A finite element model is developed with mesh refinement optimization and is further validated with the testing results, which provides a reliable way of investigating the parameter effect on the wind-induced structural responses, namely, the width and thickness of the roof sheeting and welding height. Research results show that the CWSSR system has predominant wind-resistant performance and can bear an ultimate wind uplift loading of 10.4 kPa without observable failures. The welding joints achieve equivalent mechanical behaviors as those of base material is produced with the current of 65 A. Independent structural responses can be found for the roof sheeting of the CWSSR system, and the maximum displacement appears at the middle of the roof sheeting, while the maximum stress appears at the connection supports between the roof sheeting with a significant stress concentration effect. The responses of the CWSSR system are greatly influenced by the width and thickness of the roof sheeting but are less influenced by the welding height.

• Steel and Composite Structures
• /
• 제7권1호
• /
• pp.35-52
• /
• 2007

The cold formed light-gauge profiled steel sheeting can offer considerable shear resistance acting in the steel building frame. This paper conducted the full-scale test on the shear behavior of stressed skin diaphragm using profiled sheeting connected by the self-tapping screws. A three-dimensional finite element model that simulates the stressed skin diaphragm was developed. The sheet was modeled using thin element model while the supporting members were simulated using beam elements. Fasteners were represented in the numerical model as equivalent springs. A joint test program was conducted to characterize the properties of these springs and results were reported in this study. Finite element model of the full-scale test was analyzed by use of the ANSYS package, considering nonlinearity caused by the large deflection and slip of fasteners. The experimental data was compared with the results acquired by the EUR formulas and finite element analysis.

• 한국강구조학회 논문집
• /
• 제13권6호
• /
• pp.641-649
• /
• 2001

본 논문에서는 데크플레이트의 웨브 국부좌굴에 관한 실용적인 내력식을 제안하고자 한다. 실험에서 유추된 해석모델을 이론적으로 규명한 기존의 연구를 바탕으로 내력에 영향을 미치는 주요 변수들을 조사 분석하여 관련 함수들을 유도한다. 각 변수들을 기존의 실험자료와 종합적으로 비교 분석하여 간편한 내력식을 제안한다. 유럽기준 EC 3 부록 Z 에 따른 통계평가로부터 저항 부분안전계수 ${\gamma}_M$ 을 구하며 목표로 하는 값 1.1과 비교되어진다.