• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.781-784
• /
• 2004

Method of Steel plate reinforced by fiber sheet is advantageous in the secure loading facility. For this method are a light weight and a high strength, the thickness of steel can be reduced Effects of composite system are depreciated when the thickness of steel is thin. This is the result of the difference of ductility ratio with steel plate. Steel plate reinforced by fiber sheets confirms the ability of transformation. This is the result of the property of steel materials Steel plate reinforced by fiber sheet didn't display an enough performance when theadhesives are epoxy rosin. This is the result of the slide of the surface of stee1. The adhesive ability is varied by the number and span of anchor bolts. There wasn't happening the separation between steel and epoxy. Thus the method used in combination with anchor and epoxy is best excellent. This is the result of the upward of accumulation effects Shearing force is in proportion to the number of bolts. But the ability of shearing force per one bolt is reducing. Thickness of steel plate reinforced by fiber sheet must be designed so that steel is endure before concrete is wreck.

• Korea-Australia Rheology Journal
• /
• 제15권2호
• /
• pp.55-61
• /
• 2003

The steady shear flow properties of vaseline generally used as a base of the pharmaceutical dosage forms were studied in the consideration of wall slip phenomenon. The purpose of this study was to show that how slip may affect the experimental steady-state flow curves of semisolid ointment bases and to discuss the ways to eliminate (or minimize) wall slip effect in a rotational rheometer. Using both a strain-controlled ARES rheometer and a stress-controlled AR1000 rheometer, the steady shear flow behavior was investigated with various experimental conditions ; the surface roughness, sample preparation, plate diameter, gap size, shearing time, and loading methods were varied. A stress-controlled rheometer was suitable for investigating the flow behavior of semisolid ointment bases which show severe wall slip effects. In the conditions of parallel plates attached with sand paper, treated sample, smaller diameter fixture, larger gap size, shorter shearing time, and normal force control loading method, the wall slip effects could be minimized. A critical shear stress for the onset of slip was extended to above 10,000 dyne/$\textrm{cm}^2$. The wall slip effects could not be perfectly eliminated by any experimental conditions. However, the slip was delayed to higher value of shear stress by selecting proper fixture properties and experimental conditions.

• Tribology and Lubricants
• /
• 제22권3호
• /
• pp.137-143
• /
• 2006

The sliding contact interface of machine components such as bearings, gears frequently operates in lubrication at the inception of sliding failure under high loads, speed and slip. The surface temperature at the interface of bodies in a sliding contact is one of the most important factors influencing the behavior of machine components. Most surface failure in sliding contact region result from frictional heat generation. However, it is difficult to measure temperature rise experimentally. So the calculation of the surface temperature at a sliding contact interface has long been an interesting and important subject for tribologist. The surface temperature rise is related in contact pressure, sliding speed, material properties and lubrication thickness. Though roughness, load, ect all of the condition, are same, film thickness varies with velocity. In this study, surface temperature rise due to frictional heating in lubrication is calculated with various velocities. Surface film shearing and dry solid asperity contact are used to simulate the change of frictional heat in lubricated contact

• 한국정밀공학회지
• /
• 제25권6호
• /
• pp.159-167
• /
• 2008

Cooling lubricants are used in machining operations in order to reduce friction at the tool-chip and tool-workpiece interfaces, cool both chip and tool, and remove chip. Furthermore, they influence a strong effect on the shearing mechanisms and, consequently, on the machined surface quality and tool wear. However, several researchers state that the costs related to cutting fluids is frequently higher than those related to cutting tools. Moreover, the cooling lubricants cause an increase in both worker's health and social problems related to their use and correct disposal. Therefore, many researchers have focused on the environmentally conscious machining technologies. One of the technologies is known as MQL(Minimum Quantity Lubrication) machining. In this paper, an experimental model to obtain the optimal cutting conditions in MQL turning was suggested, and the effects of cutting conditions on surface roughness and cutting force were analyzed. For these purposes, FFD (Fractional Factorial Design) and RSM (Response Surface Methods) were used for the experiment. Cutting force and surface roughness with different cutting conditions were measured through the external cylindrical turning of Al 6061 based on the experiment plan. The measured data were analyzed by regression analysis and verification experiments with random conditions were conducted to confirm the suggested experimental model.

• 소성∙가공
• /
• 제27권3호
• /
• pp.145-153
• /
• 2018

Magnesium material could be widely used in the automotive industry because of its high strength to weight ratio, but the electric resistance spot welding process of magnesium sheets is difficult because of its low electric resistance and high thermal conduction and thermal expansion. For this reason, an electric resistance surface friction spot welding process using rotating dies is suggested for the spot welding of magnesium metal sheets. This welding method can be characterized by three heating methods: (1) electric resistance heating on contacted surface, (2) surface friction heating by rotating dies, and (3) thermal conduction heating from heated steel electrodes, for the fusion of metal at the interfacial zone between the two magnesium sheets. This welding process also has variables to explore, such as welding currents, diameters of the steel electrode, and rotating dies. It was found that the welding strength could reach industrial requirements by applying a welding current of 11.0kA, with steel electrodes of 12mm diameter, with rotating dies of 4.4 mm diameter, under the condition of a revolution speed of 1200rpm of rotating dies, for the surface friction spot welding process of AZ31 magnesium alloy sheets of 1.4mm thickness.

• 한국염색가공학회지
• /
• 제8권3호
• /
• pp.52-58
• /
• 1996

In order to study an applicable level for the graft finish of silk filaments and the characteristics of silk fabric, some sample fabrics were woven with grafted weft and the characteristics of sample fabrics were analyzed to evaluate the mechanical properites and the handle values according to the graft yield(%) of MMA and HEMA monomers on silk filaments. 1. The tensile properties were detected in the increase of linearity(LT) and the recovery in time of the increasing resilience(RT). 2. The bending properties were detected to have a lot of effect on the balance of bending rigidity(B) to hysteresis(2HB) according to the elastic relaxation of warp tension and the interlacing stress. 3. The shearing properities were detected to show the softness and the elastics in a case of the decrease in shearing rigidity(G) and hysteresis(2HG, 2HG5) according to the graft yields. 4. The compression properties were detected in the decrease of linearity(LC) and the uniformity of resilience(RC). It explains that the tendancies of compressible variation is not accepted. 5. The surface properities were detected to be affected by the surface forms of grafted silk filaments and the variation in the morphologies of interlacing sections. Considering the interlacing eveness, MMA grafted fabrics were accepted within the level of WOMEN'S THIN DRESS(KN-201-LDY) but HEMA grafted fabrics were not accepted. 6. The variation of handles were detected in the increase of total hand(TAV) within the levels of 65% of KOSHI and 82% of HARI on the average. 7. The handle fashions were detected in the nature of Habuta and Dechine from MAA graft but the nature of Fugi were shaped from HEMA graft in proportion to the graft yields.

• 한국지반공학회논문집
• /
• 제29권5호
• /
• pp.39-52
• /
• 2013

본 연구는 포화-압밀-전단 제어형 링전단시험장치를 이용하여 (i) 전단시간에 따른 전단응력 특성, (ii) 구속압과 전단속도에 따른 전단특성 및 (iii) 전단속도에 따른 전단응력 특성에 대한 연구를 수행하였다. 이질 재료간의 전단특성을 살펴보고자 낙동강 모래와 해안 점토를 사용하였다. 본 연구에서는 모래와 모래, 점토와 점토, 모래와 점토끼리의 전단특성을 살펴보고자 비배수 조건에서 특정 구속압(50과 100kPa)에 대한 실험을 1차적으로 수행하였다. 모든 실험은 특정 구속압에 대해 300sec 동안 자동 압밀조건을 거친 후 전단실험을 수행하였다. 2차 실험으로 세 시료에 대한 수직응력 변화에 따른 전단응력 특성을 살펴보고자 수직응력을 20~150kPa까지 단계별로 높여가며 실험을 수행하였다. 마지막으로 특정 구속압에 대해 전단속도를 0.01, 0.1, 1, 10, 100mm/sec까지 5 단계로 나누어 실험을 수행하였다. 이질재료 간의 전단응력은 특정 구속압 하에서 모래-점토의 전단응력(최대전단응력과 잔류전단응력)은 모래-모래보다는 작고, 점토-점토보다는 약간 큰 것으로 나타났다. 전단응력은 구속압과 전단속도에 의해 전단면에서 발생하는 입자 파쇄와 젖음현상에 의존하는 것으로 나타났다.

• 한국강구조학회 논문집
• /
• 제9권4호통권33호
• /
• pp.543-555
• /
• 1997

일반적으로 합성형 교량에 있어서 강판형과 콘크리트 슬래브 사이의 일체성은 강재와 콘크리트라는 이질재료의 접합부 사이에 위치한 전단연결재의 강성과 배치간격에 의해 영향을 받게 된다. 따라서 전단연결재는 두 재료가 일체로 거동할 수 있도록 충분한 강성을 가져야만 하며, 강성이 부족하게 되면 접촉면에서 미끄러짐이 발생한다. 이때, 미끄러짐의 발생을 고려한 것을 불완전합성형이라 한다. 본 논문에서는 불완전합성형의 해석에서 복잡한 계산과정을 거치지 않고 불완전율에 따라서 전단연결재의 강성과 간격을 산정하는 간이추정법에 대하여 연구하였으며, 단면과 지간에 따른 형특성, 불완전율, 하중작용점에 따라서 전단연결재에 작용하는 수평전단력, 축력 등의 변화양상을 간단한 영향선으로 나타내었다. 또한, 해석 예로서 Newmark의 partial interaction theory이론을 기초로 한 블완전합성형의 기초미분방정식을 적용하여 불완전율에 따라서 1) 스프링상수와의 관계 2) 축력 및 수평전단력과의 관계 3) 응력 및 중립축과의 관계를 고찰하였다.

• 한국의류학회지
• /
• 제19권4호
• /
• pp.684-695
• /
• 1995

The purpose of this study was to investigate the influence of the mechanical properties on drapability in the peach skin-like finished fabrics. For this study, the samples used were 50 kinds of peach skin-like finished fabrics. The mechanical properties such as tensile, shearing, bending, compressional, surface characteristic values, thickness and weight were measured with a KES-F system and drupe coefficient by drape tester. The relationship between the characteristic values and drape coefficicients of the peach skin-like finished fabrics results were obtained. 1. Peach skin-like finished fabric had $\pm$2o range of shearing, bending, compression, surface. properties, thickness and weight as compared with Japanese women's thin fabrics. The characteristic mixing values were better with the values of WC/T, W/T, etc. as compared with that of japanese women's thin fabrics. Accordingly, the peach skin-like finished fabrics had a little volume, excellent hanging and drapability as compared with japanese women's thin fabrics. 2. The drape coefficient of peach skin-like finished fabric had a high level of correlation between 2HB, G, WC, MIU, WT, MMD, 2HG, RT, W, B etc. of the mechanical properties. The blocked properties that contributed to the drape coefficient of peach skin-like finished fabrics were in the order of the bending> tensile> thickness> weight properties. This drape coefficients(DC) were found by measuring the mechanical properties according to the obtained regress on equate on. DC=99.0179+17.9023 log G -17.0543 log 2HG5+17.2104 log 2HG+35.7685 log 2HB+ 4.6082 log B-30.5906 log T+4.2308 log W 3. The contribution to the drape coefficient of the characteristic mixing values of peach skin-like finished fabric was in the order of > 2HB/W> 2HB/B> B/W The drape coefficients were found by measuring the characteristic mixing values according to the obtained regression equation. 4. The drape coefficients of peach skin-like finished fabrics were influenced by the differences between the bending of warp direction, bending of weft direction, shearing etc which in turn determine the level of hanging. The regression equation was as follows; 5. The drape coefficients of peach skin.like finished fabrics had a highly positive correlation with the node index. It has an negative correlation with number of nodes.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 토목섬유 학술발표회 논문집
• /
• pp.57-68
• /
• 1999

This paper summarizes the results of a study which uses the recently developed Optical Profile Microscopy technique (Dove and Frost, 1996) as the basis for investigating the role of geomembrane surface roughness on the shear mechanism of geomembrane/geotextile interfaces. The alternative roughness parameters which consider the direction of shearing are described. These directional parameters are compared with the existing roughness parameters, and the relationship between these directional and non-directional parameters are investigated. Then, the relationship between interface shear strength and surface roughness quantified at the interface is investigated. The results show that interface friction can be quantitatively related to the surface roughness of the geomembrane. The peak and residual interface strengths increase dramatically through the use of textured geomembranes as opposed to smooth geomembranes. For the smooth geomembranes, the sliding of the geotextile is the main shear mechanism. For the textured geomembranes, the peak interface strength is mainly mobilized through the micro-texture of the geomembrane, however, the residual interface strength is primarily attributed to macro scale surface roughness which pulls out and breaks the filaments from the geotextile. The results of this study can be extended to the other interfaces such as joints in rock mass, and also can be used to provide a quantitative framework that can lead to a significantly improved basis for the selection and design of geotextiles and geomembranes in direct contact.