• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.682-690
• /
• 2015

The bonding performance of two types of wood adhesives, namely phenol-resorcinol-formaldehyde (PRF) resin and melamine-urea-formaldehyde (MUF) resin for glued laminated timber manufactured by high frequency (HF) heating was evaluated. The HF heating system consists of HF oscillator with dielectric heating system for curing adhesives, and hydraulic press system for clamping glued laminated timber. The designed frequency and output power of the HF system was as 5 MHz and 60 kW, respectively. To verify dielectric heating mechanism under HF oscillation, the heat loss factors of laminae and adhesives were measured. The results show that it is possible to selectively heat adhesives for their curing due to the remarkably higher loss factor of the adhesives than those of wood laminae. The temperature of adhesive in the bonding line reached up to the set temperature within a few seconds by high frequency oscillating, which advanced the curing of adhesive afterwards. The bonding performance, such as shear strength of bonding line, water soaking delamination, and boiling water soaking delamination of PRF resin met the requirement of Korean Standard (KS), however the MUF resin did not meet the KS requirement of boiling water soaking delamination. These results indicate that the HF heating system is successful to manufacture glued laminated timbers with PRF resins to meet the bonding requirements.

• Journal of Nutrition and Health
• /
• v.10 no.3
• /
• pp.1-6
• /
• 1977

Flow properties of heated edible oils, such as soybean, rapeseed, rice bran, corn and perilla oils, were measured with Maron-Belner type capillary viscometer. These oils were heated at $180{\pm}5^{\circ}C$ (general cooking temperature) for $5{\sim}20$ hours except soybean oils ($5{\sim}40$ hours). Fluidities of these heated oils except rice bran oil were decreased according to heating time and decreasing ratio of fluidity was outstanding after 15 hour heating in corn oil and 20 hours heating in soybean and perilla oils. All the oils examined in this experiments except rice bran oil showed non-Newtonian motion after 15 hour hinting at high shear stress and Newtonian motion at less than 10 hour heating. In the soybean oil non-Newtonian flow property was outstanding after 30 hour heating at $180{\pm}5^{\circ}C$. Rice bran oil exhibit characteristic flow property, that is, non heated rice bran oil has lowest fluidity but heated one has highest fluidity compared to other oils examined in this experiment. Change of fluidity with extension of heating time was not detected and non heated rice bran oil showed non-Newtonian motion.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.103-110
• /
• 2021

Elastomeric bearings composed of flexible rubber materials and steel reinforcement plates are widely used for seismic retrofit of bridges due to their excellent vertical stiffness and flexible lateral stiffness. Especially, it has the advantages of simple construction and low cost. Chloroprene rubber, a type of rubber material, has greater resistance to aging than natural rubber, but its performance is also degraded due to various deterioration factors. Although these aging characteristics are not reflected in the seismic design standards and seismic performance evaluation guidelines, it is reasonable to reflect this when related studies are accumulated. For chloroprene rubber, accelerated heat aging test was performed with variables of heating temperatures and exposure time to analyze shear characteristics. As aging progresses the maximum shear stress and shear strain decrease. Also, the shear stiffness is greatly increased at the same shear strain.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.12
• /
• pp.33-39
• /
• 2018

In this study, important characteristics were identified for the Geosynthetic-soil interface using overburden pressure and saltwater and fresh water to evaluate silt shear behavior of the Geosynthetic-soil interface. In addition, waste landfill can secure spaces for waste disposal in the sea and this spaces can be used for additional facilities which will be necessary in the future. Analysis of behavior characteristics on interface of Geosynthetic-soil shows that, if analyzed using standard consolidometers, the consolidation stress of fresh water increased significantly more than saltwater. When analyzed using cyclic shear apparatus, saltwater and freshwater in both conditions, the displacement value increases as the wire gauges become closer to the lower module, and the shear fracture tends to occur radically under saltwater conditions than fresh water. Therefore, seawater, fresh water that act on the interface of geosynthetic-soil, and installation of facility using geosynthetic should be considered as important parameters that are essential for the dynamic design factor of the water controlling facility.

• Journal of Industrial Technology
• /
• v.25 no.B
• /
• pp.121-126
• /
• 2005

Micro wires manufactured by the straightening process are used in the BT(Bio-Technology), IT(Information-Technology), NT(Nano-Technology). We have developed a novel wire straightener which uses the direct heating method(DHM) for straightening the micro wire and shearing device for burr-less cutting. In this study, we confirm the tendency of micro wire after the shearing process. It is impossible to remove the burr in the shearing process. However, the embodiment of minimum burr size after the shearing process is the best in-process method. In order to minimize the burr size, we have accomplished the various experiment condition such as the U-groove, the effect of the counter punch, the shear angle, clearance.

• Journal of Welding and Joining
• /
• v.16 no.5
• /
• pp.100-107
• /
• 1998

This paper describes fluxless soldering of reflow soldering process using solder foil instead of solder pastes. There is an increasing demand for the reliable solder connection in the recent high density microelectronic components technologies. And also, it is problem fracture of an Ozone layer due to freon as which is used to removal of remained flux on the substrate. This paper discussed joining phenomena, boudability and joining processes of microelectronics devices, such as between outer lead of VLSI package and copper pad on a substrate without flux. The shear strength of joints is 8 to 13 N using Sn/Pb (63/37 wt.%) solder foil with optimum joining conditions, meanwhile, in case of using Sn/In (52/48 wt.%) solder foil, it is possible to bond with low heating temperature of 550 K, and accomplish to high bonding strength of 25N in condition heating temperature of 650K. Finally, this paper experimentally shows fluxless soldering using solder foil, and accomplishes key technology of microsoldering processes.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.231-233
• /
• 2005

Laser have been utilized as a heat source for the soldering of electronic components for the their capability of localized heating and faster heating rate. Laser soldering process, especially the diode laser soldering of BGA solderball was investigated. In this study, an attempt was made to investigate the possibility of laser soldering using Sn-37Pb and Sn-3Ag-0.5Cu solderball. The laser energy absorbed on the pad raised the temperature of the solderball forming a reflowed solder bump. The result were discussed based on the measurement of pull and shear strength of the bond.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.443-448
• /
• 1996

In this paper, the 100 % non-inductive current drive scenarios are addressed for the steady-state operation on KT-2 tokamak, with the profile control using fast wave and lower hybrid wave as the external tools. Considering the stability, the well-aligned current profiles with a reversed-shear and $q_{min}$ > 2.0 has been favor-able in high ${\beta}_{p}$ plasma, together with a possibly higher bootstrap current fraction. Therefore, the effects of the auxiliary heating power profile on the control of MHD favorable current profile are evaluated in detail.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.12
• /
• pp.1275-1281
• /
• 2001

Aqueous polymer solutions are known to have small pressure reduction. Paraffin slurries are known to have high thermal capacity. Paraffin particles are mixed into an aqueous polymer solution to make a new heat transfer fluid having high thermal capacity but low pressure reduction. The heat transfer characteristics of the new slurry was tested in a circular tube having a constant heat transfer boundary condition. The new slurry was found to have high Nusselt numbers as well as high thermal capacity and low pressure reduction in the laminar flow. The trends of the Nusselt numbers along the heating test section were studied for various heating conditions.

• Journal of Nutrition and Health
• /
• v.11 no.1
• /
• pp.33-37
• /
• 1978

The effect of heating time (0 to 30 hours at $180{\pm}5^{\circ}C$) on the change of flow properties, fatty acid compositions and some other characteristics such as acid value, iodine value, peroxide value and density of purified edible rice bran oil were observed. flow properties were measured with Maron-Belner type capillary viscometer. Newtonian motion was observed in non-heated oil and the oil heated for 5 hours but non-Newtonian motion was observed in the oil heated for more than 10 hours and at high shear stress. The fatty acid compositions were analyzed by gas liquid chromatography and all the components of fatty acids were reduced in amounts with extention of heating time. The acid value, peroxide value and density were increased but iodine value were decreased with extension of heating time.