• 센서학회지
• /
• 제7권6호
• /
• pp.437-445
• /
• 1998

Bias 스프링을 이용한 형상기억합금 액츄에이터는 양방향 동작기구로서 이용이 가능하다. 이러한 bias식 형상기억합금 액츄에이터를 설계하기 위해서는 발생력이나 작동변위 등의 설계 사양이 만족되도록 형상기억합금스프링 및 bias 스프링의 구조를 결정하여야 한다. 본 논문에서는 bias식 형상기억합금 액츄에이터의 설계방법으로서, 경험적 가정에 의존하는 기존의 방법과는 달리 주어진 설계 사양만으로부터 직접 설계가 가능한 새로운 방법을 제시하고 이를 실험결과와 비교하였다. 실험값도 설계값과 비교적 잘 일치하여 제시된 설계방법의 타당성 및 유용성을 검증하였다.

• 한국해양공학회지
• /
• 제6권1호
• /
• pp.87-95
• /
• 1992

Recently, the robot actuator worked by the driving recovery-force of the thermo elastic martensitic transformation of shape memory alloys(SMA) has been studied. In general, such a SMA actuator necessitates a number of cyclic repeated motion, so that the investigation of gradual decrease of recovery force with repeated motion cycle as well as the prevention of such a degradation of shape memory effect(SME) are very important for the actual use of a robot actuator. However, such research and discussions about the degradation of SME are very few up to the present. Therefore, in this study, the characteristics of the cyclic deformation and degradation of SME of Ti-Ni alloy would be investigated and discussed in detail by current heat type fatigue tester, which is a newly designed fatigue tester by author. In addition, we will establish a new design concept for robot actuator from these result.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.210-215
• /
• 2008

This paper presents an experimental study on a bending actuator with a shape memory alloy wire. In this study, we introduced design process and experimental result of the bending actuator. The bending actuator consists of a SMA wire, springs, and a glass/epoxy strip. In the bending actuator, springs were used to restore the SMA wire to its initial shape right after actuation. To obtain properties of the SMA wire, DSC test was performed and the behavior of the SMA wire under different loadings was observed. Finally, the proposed bending actuator shows reasonable actuation behavior with relatively lower power consumption, fast response and effective efficiency.

• 한국의류학회지
• /
• 제44권6호
• /
• pp.1154-1162
• /
• 2020

In this study, the soft textile actuator is produced for a smart wearable with the shape memory effects from linear shape memory alloys of Nickel and Titanium using the driving force through the fabrication process. The measurement model was designed to measure dynamic characteristics. The heating method, and memory shape of the linear shape memory alloy were set to measure the operating temperature. A shape memory alloy at 40.13℃, was used to heat the alloy with a power supply for the selective operation and rapid reaction speed. The required amount of current was obtained by calculating the amount of heat and (considering the prevention of overheating) set to 1.3 A. The fabrication process produced a soft textile actuator using a stitching technique for linear shape memory alloys at 0.5 mm intervals in the general fabric. The dynamic characteristics of linear shape memory alloys and actuators were measured and compared. For manufactured soft textile actuators, up to 0.8 N, twice the force of the single linear shape memory alloy, 0.38 N, and the response time was measured at 50 s.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.263-270
• /
• 1995

The use of the shape memory alloy, Nitinol wire, is investigated as an actuator for enhancing the damping in structural vibration systems. The first-order mathematical model of the Nitinol wire is obtained from the experimental data for an actuator. Finite element method is utilized for the strain gage sensor model, which is installed at the root of cantilever beam. A simple system, cantilever beam, is built as a flexible structural system to implement a control law with the Nitinol wire actuator. The system model including sensor and actuator is derived, which agrees with the experimental results. The actuator dynamics is augmented with the system so as to design PI controller and the one of robust controllers, LQG/LTR controller, and the control laws are implemented experimentally. The experimental study shows the feasibility of utilizing the Nitinol wire as an actuator for the purpose of vibration control.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2005년도 춘계 학술대회논문집
• /
• pp.100-103
• /
• 2005

This work discusses the numerical analysis, the design and experimental test of the SMA (Shape Memory Alloy) actuator along with its capabilities and limitations. Convection heating and cooling using water actuate the SMA element of the actuator. The fuel such as propane, having a high energy density, is used as the energy source for the SMA actuator in order to increase power and energy density of the system, and thus in order to obviate the need for electrical power supplies such as batteries. The system is composed of a pump, valves, bellows, a heater (burner), control unit and a displacement amplification device. The actuation frequency is compared with the prediction obtained from numerical analysis. For the designed SMA actuator system, the results of numerical analysis were utilized in determining design parameters and operating conditions.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권4호
• /
• pp.269-274
• /
• 1999

A bending actuator using zigzag type shape memory alloy springs has been fabricated and characterized. The fabricated millimeter-sized actuator has outer diameter of 3.0mm and inner diameter of 2.0mm. The zigzag type spring is more suitable for thin wall type actuator because the zigzag type spring has a planar structure comparing with the coil type spring which has a three-dimensional structure. The measured characteristics of the fabricated bending actuator show the possibility of practical application to micro active bending catheters.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 추계학술대회
• /
• pp.497-500
• /
• 1997

In this paper, we proposes a bending actuator using shape memory alloy coil-type springs. By the heating of two shape memory alloy coil-type springs sequentially, the bending and stretching motion of the actuator is possible. We measure the bending angle and repeated bending motion with the various currents. Furthermore, we control the bending angle of the 1 directional bending actuator with sensors. The performance of the actuator has been characterized or the possible application for catheter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 G
• /
• pp.2512-2514
• /
• 1998

The bending actuator using zigzag type shape memory alloy springs has been fabricated and characterized. The small sized actuator with outer diameter of 3.0mm and inner diameter of 2.0mm could be implemented because zigzag type spring has advantages for thin wall type actuator over the coil type spring. The measured characteristics of the fabricated bending actuator show the possibility of practical application to micro active bending catheter.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.75-79
• /
• 2001

In the recent years, as the research and the development of micro and precision machinery become active, the interest of micro actuators using SMA(Shape Memory Alloy) has been increased. The dynamic characteristic analysis of SMA is necessary for actuator application and many common researches report the material characteristics of SMA sufficiently. However, the research on dynamic characteristics is very deficient. In this paper, the helical spring are fabricated with NiTi SMA wire of high resistivity, The force, response speed, temperature, and displacement are measured by digital force gauge, infrared thermometer, and laser displacement sensor so that the dynamic characteristics of this SMA is analyzed. Also, bidirectional actuator was fabricated and experimented for its performance.