• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.225-229
• /
• 2009

The front metal contact is one of the most important element influences in efficiency in the silicon solar cell. First of all selective of the material and formation method is important in metal contacts. Commercial solar cells with screen-printed contacts formed by using Ag paste process is simple relatively and mass production is easy. But it suffer from a low fill factor and a high shading loss because of high contact resistance. Besides Ag paste too expensive. because of depends income. This paper applied for Ni/Cu metallization replace for paste of screen printing front metal contact. Low cost Ni and Cu metal contacts have been formed by using electroless plating and electroplating techniques to replace the screen-printed Ag contacts. Ni has been proposed as a suitable silicide for the salicidation process and is expected to replace conventional silicides. Copper is a promising material for the electrical contacts in solar cells in terms of conductivity and cost. In experiments Ni/Cu metal contact applied same grid formation of screen-printed solar cell. And it has variation of different grid spacing. It was verified that the wide spacing of grid finger could increase the series resistance also the narrow spacing of grid finger also implies a grid with a higher density of grid fingers. Through different grid spacing found alteration of efficiency.

• 한국태양에너지학회 논문집
• /
• 제37권2호
• /
• pp.47-57
• /
• 2017

CIGS thin film solar cells are technically suitable for BIPV applications than regularly used crystalline silicon solar cells. Particularly, CIGS PV has lower temperature coefficient than crystalline silicon PV, thus decrease in power generation is lowered in CIGS PV. Moreover, CIGS PV can decrease shading loss when applied to the BIPV system, and the total annual power generation is higher than crystalline silicon. However, there are few studies on the installation factors affecting the performance of BIPV system with CIGS module. In this study, BIPV curtain wall unit with CIGS PV module was designed. To prevent increase of temperature of CIGS PV module by solar radiation, ventilation was considered at the backside of the unit. The thermal specification and electrical performance of CIGS PV of the ventilated unit was analyzed experimentally. Non-ventilated unit was also investigated and compared with ventilated unit. The results showed that the average CIGS temperature of the ventilated curtain wall unit was $6.8^{\circ}C$ lower than non-ventilated type and the efficiency and power generation performance of ventilated CIGS PV on average was, respectively, about 6% and 5.8% higher than the non-ventilated type.

• 한국재료학회지
• /
• 제28권1호
• /
• pp.38-42
• /
• 2018

Continuous efforts are being made to improve the efficiency of Si solar cells, which is the prevailing technology at this time. As opposed to the standard front-lit solar cell design, the back-lit design suffers no shading loss because all the metal electrodes are placed on one side close to the pn junction, which is referred to as the front side, and the incoming light enters the denuded back side. In this study, a systematic comparison between the two designs was conducted by means of computer simulation. Medici, a two-dimensional semiconductor device simulation tool, was utilized for this purpose. The $0.6{\mu}m$ wavelength, the peak value for the AM-1.5 illumination, was chosen for the incident photons, and the minority-carrier recombination lifetime (${\tau}$), a key indicator of the Si substrate quality, was the main variable in the simulation on a p-type $150{\mu}m$ thick Si substrate. Qualitatively, minority-carrier recombination affected the short circuit current (Isc) but not the opencircuit voltage (Voc). The latter was most affected by series resistance associated with the electrode locations. Quantitatively, when ${\tau}{\leq}500{\mu}s$, the simulation yielded the solar cell power outputs of $20.7mW{\cdot}cm^{-2}$ and $18.6mW{\cdot}cm^{-2}$, respectively, for the front-lit and back-lit cells, a reasonable 10 % difference. However, when ${\tau}$ < $500{\mu}s$, the difference was 20 % or more, making the back-lit design less than competitive. We concluded that the back-lit design, despite its inherent benefits, is not suitable for a broad range of Si solar cells but may only be applicable in the high-end cells where float-zone (FZ) or magnetic Czochralski (MCZ) Si crystals of the highest quality are used as the substrate.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.906-911
• /
• 2008

Because the perimeter of buildings is strongly influenced by solar and the outdoor air temperature, the area has different environmental properties compared to the interior of a building, as in summer heat gain, and in winter heat loss. In particular, if the external wall is glass, the characteristics of the glass material make it pervious to outside conditions, thereby making big changes to the thermal environment. By combining shading device and the efficient exhaust system, an energy saving can be achieved compared to no air barrier systems. The simplified air barrier system is developed with the idea that energy could be conserved by carefully and effectively blowing out the air caught between the glass surface and the roller blind. The way it is configured is therefore by making the roller blind's air-path, and by placing the air output ducts in the most optimum positions. This simplified air barrier system will give improvement in the thermal environment of the parameter area that is strongly affected by solar and the outdoor condition.

• 한국농공학회지
• /
• 제29권4호
• /
• pp.117-123
• /
• 1987

This study was conducted to develop an automatic insulation system to reduce the heat loss through the wall of greenhouses during the nighttime in winter. A double covered model vinyl house was constructed, and blowers were used to fill or remove styrene pellets automatically the inside of the double-wall of the double covered vinyl house. The effects of insulation of the double covered vinyl house insulated with the styrene pellets were analyzed by comparing with the single covered vinyl house. The results obtained from this study can be summarized as follows : 1. The optimum thickness of the double-wall of the double covered vinyl house was found to be 5 to 10 cm. 2.When the outside temperature varied in the range of -8.3 to -1.5$^{\circ}C$ during the nighttime, the inside temperature of the double covered vinyl house insulated with the styrene pellets showed 7.7 to 11.7$^{\circ}C$ and the inside temperature of the single covered vinyl house showed -5.8 to 2.3$^{\circ}C$. Therefore, the effects of insulation of the double covered vinyl house insulated with the styrene pellets were confirmed to be excellent. 3. Also, the excessive increase of the inside temperature in the vinyl house was prevented by the shading effect of the double covered vinyl house insulated with the styrene pellets during the daytime. 4. When the outside temperature varied in the range of 17.7 to 30.0$^{\circ}C$ during the daytime, it was possible to keep the inside temperature at 30${\pm}$4$^{\circ}C$ in the double covered vinyl house by operating the insulation system. 5. The transmissivity of the double covered vinyl house with the styrene pellets removed was 52.4 % on the average.

• 한국인터넷방송통신학회논문지
• /
• 제20권5호
• /
• pp.157-162
• /
• 2020

기존의 태양광발전장치 중에서 반사판을 갖춘 장치는 태양에너지(일사량)를 태양광 모듈 표면에 집중적으로 입사되는 방식이지만 태양광 모듈을 통해 다시 반사되어 손실되는 태양에너지(일사량)는 고려되지 않는 구조로 되어있다. 또한, 태양광 모듈 주위에 반사판을 설치하여 발전량을 높이는 방안이 제시되고 있지만, 이는 다른 태양광 모듈의 음영에 따른 발전 저하에 영향을 주고 있다. 따라서 이러한 문제점을 개선하고자 본 논문에서는 1) 음영에 따른 태양광 모듈의 발전에 영향을 주지 않으면서 2) 태양광 모듈에서 반사되어 손실되는 태양에너지(일사량)를 회전하는 반사판을 이용하여 태양광 모듈에 다시 입사되는 방법을 연구 및 제안한다. 따라서 손실된 태양에너지(일사량)의 무수한 반사 각도에 따른 태양에너지를 재활용할 수 있는 방법을 통해 태양에너지(일사량)에 대한 손실을 최소화, 동일 일사량에 대한 발전량을 최대화하므로 태양광발전장치의 발전량을 증가시킬 수 있다.

• 한국태양에너지학회 논문집
• /
• 제38권2호
• /
• pp.45-53
• /
• 2018

For the preliminary step for estimating the performance of roof-type photovoltaic system in urban areas, we analyzed the solar radiation reduction ratio by shadow effect by buildings using DSM (Digital Surface Model) and GIS (Geographical Information System) tools. An average loss by the shadow is about 19% in Seoul. The result was related to the building density and distribution. Monthly results show that the winter season (December and January) was more affected by the shading than during the summer season (June and July). It is expected that useful empirical formulas can be made if more detailed correlation studies are performed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.192-193
• /
• 2007

An evaporated Ti/Pd/Ag contact system is most widely used to make high-efficiency silicon solar cells, however, the system is not cost effective due to expensive materials and vacuum techniques. Commercial solar cells with screen-printed contacts formed by using Ag paste suffer from a low fill factor and a high shading loss because of high contact resistance and low aspect ratio. Low-cost Ni and Cu metal contacts have been formed by using electro less plating and electroplating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Ni/Cu alloy is plated on a silicon substrate by electro-deposition of the alloy from an acetate electrolyte solution, and nickel-silicide formation at the interface between the silicon and the nickel enhances stability and reduces the contact resistance. It was, therefore, found that nickel-silicide was suitable for high-efficiency solar cell applications. Cu was electroplated on the Ni layer by using a light induced plating method. The Cu electroplating solution was made up of a commercially available acid sulfate bath and additives to reduce the stress of the copper layer. In this paper, we investigated low-cost Ni/Cu contact formation by electro less and electroplating for crystalline silicon solar cells.

• 수산해양기술연구
• /
• 제37권3호
• /
• pp.196-213
• /
• 2001

체장어군탐지기(fish sizing echo sounder) 의송.수파기로서 사용하기 위한 split beam 음향 변환기를 개발하기 위한 시도로서, Dolph Chebyshev배열 기법을 이용하여 36개의 압전 진동소자에 진폭 가중치를 부여한 평면배열 음향 변환기를 설계.제작하고, 이 변환기의 수중음향방사 특성에 대해 분석.고찰한 결과를 요약하면 다음과 같다. 1. split beam 음향 변환기의 4 개의 독립적인 진동자 블록에 대한 수중에서의 평균적인 공진 및 반공진 주파수는 각각 69.8 kHz. 83.0 kHz이었고, 이들 공진과 반공진 주파수에서의 임피던스는 49.2$\omaga$. 704.7$\omaga$이었다. 음향변환기의 4 개의 모든 진동자 블록 (sum beam)에 대한 수중에서의 공진 및 반공진 주파수는 각각 71.4 kHz, 82.1kHz이었고. 이들 공진과 반공진 주파수에서의 임피던스는 15.2$\omaga$, 17.3$\omaga$이었다. 2 split beam 음향 변환기의 4 개의 독립적인 진동자 블록에 대한 최대 송파전압감도(TVR)는 공통적으로 70.0 kHz에서 165.5 dB이었고, -3 dB 점에 대한 송신 주파수 대역폭은 10.0 kHz이었다. 또한. split beam 음향 변환기의 4 개의 조합된 진동자 블록에 대한 최대 수파감도(SRT)는 공통적으로 75.0 kHz에서 -177.5 dB이었고, -3 dB 점에 대한 수신 주파수 대역폭은 10.0 kHz이었다. 3.split beam 음향 변환기의 모든 진동자 블록에 대한 송신 지향성패턴은 원형이었고, -3 dB점에 대한 수평 및 수직방향에 대한 반감각(half beam angle)은 공통적으로 $9.0^\circ$이었다. 또한. 수평방향에 대한 제 1차 부엽 준위는 $22^\circ$및 $-26^\circ$에서 각각 -19.7 dB. -19.4 dB이었고. 수직방향에 대한 제1차 부엽 준위는 $22^\circ$및 $-26^\circ$에서 각각 -20.1 dB, -22.0 dB로서 설계 목표치 -20 dB과 매우 유사한 값을 나타내었다. 4.split beam 음향 변환기의 송파응답파형과 수파응답파형은 각각 송신 및 수신 공진주파수 부근인 70.0 kHz와 75.0 kHz에서 전기 입력펄스파형과 가장 유사한 특성을 나타내었다. 5. 본 연구에서 설계, 개발한 split beam 음향 변환기의 성능을 분석하기 위해 반사강도 보정을 위한 지향성손실과 물표의 위치각을 추정하기 위한 실험을 행한 결과 실험적으로 추정한 위치각은 실제적인 위치각과 잘 일치하였다.