• Horticultural Science & Technology
• /
• v.32 no.4
• /
• pp.473-483
• /
• 2014

In this work, the effects of shade combination, shade height and wind regime on greenhouse climate were quantified. A two-dimensional (2-D) computational fluid dynamics (CFD) model was developed based on an 11-span plastic greenhouse in eastern China for wind almost normal to the greenhouse orientation. The model was first validated with air temperature profiles measured in a compartmentalized greenhouse cultivated with mature lettuce (Lactuca sativa L., 'Yang Shan'). Next, the model was employed to investigate the effect of shade combinations on greenhouse microclimate patterns. Simulations showed similar airflow patterns in the greenhouse under different shade combinations. The temperature pattern was a consequence of convection and radiation transfer and was not significantly influenced by shade combination. The use of shade screens reduced air velocity by $0.02-0.20m{\cdot}s^{-1}$, lowered air temperature by $0.2-0.8^{\circ}C$ and raised the humidity level by 0.9-2.0% in the greenhouse. Moreover, it improved the interior climate homogeneity. The assessment of shade performance revealed that the external shade had good cooling and homogeneity performance and thus can be recommended. Furthermore, the effects of external shade height and wind regime on greenhouse climate parameters showed that external shade screens are suitable for installation within 1 m above roof level. They also demonstrated that, under external shade conditions, greenhouse temperature was reduced relative to unshaded conditions by $1.3^{\circ}C$ under a wind speed of $0.5m{\cdot}s^{-1}$, whereas it was reduced by merely $0.5^{\circ}C$ under a wind speed of $2.0m{\cdot}s^{-1}$. Therefore, external shading is more useful during periods of low wind speed.

• Textile Coloration and Finishing
• /
• v.21 no.5
• /
• pp.27-34
• /
• 2009

PET fabric was dyed in black shade with disperse dyes of three primary color. The effect of combination ratio of dye concentration and energy type of disperse dye on dyeing and color property of black dyed PET fabric was investigated. Dyeing compatibility of disperse dyes of three primary color on PET was evaluated by comparison of dyeing rates of them. From the results, color property was dependent upon the combination ratio of dye concentration. In order to obtain low lightness ($L^*$) and black color, blue dye should be added enough. S-type disperse dye and $130^{\circ}C$ dyeing was suitable rather than SE-type dyes or $120^{\circ}C$ dyeing. Disperse dyes of three primary color used showed good dyeing compatibility at high dye concentration. Washfastness was fair to moderate and lightfastness was moderate.

• Asian-Australasian Journal of Animal Sciences
• /
• v.33 no.6
• /
• pp.1034-1041
• /
• 2020

Objective: The objective of this experiment was to evaluate the effect of shade allocation and shade plus fan on growth performance, dietary energy utilization and carcass characteristics of feedlot cattle under tropical ambient conditions Methods: Two trials were conducted, involving a total of 1,560 young bulls (289±22 kg BW) assigned to 24 pens (65 bulls/pen and 6 pens/treatment). Pens were 585 ㎡ with 15 m fence line feed bunks. Shade treatments (㎡ shade/animal) were: i) limited shade (LS) to 1.2 ㎡ shade/animal (LS_1.2); ii) limited shade to 2.4 ㎡ shade/animal (LS_2.4); iii) total shade (TS) which correspond to 9 ㎡/animal, and iv) total shade equipped with fans (TS+F). Trials lasted 158 and 183 days. In both studies, the average weekly maximum temperature exceeded 34℃. Results: Increasing shade allocation tended (p = 0.08) to linearly increases average daily gain (ADG), and dry matter intake (DMI, quadratic effect, p = 0.03). This effect was most apparent between LS_1.2 and LS_2.4. Shade allocation, per se, did not affect gain efficiency or estimated dietary net energy (NE). Compared with TS, TS+F increased (p<0.05) ADG, gain efficiency, and tended (p = 0.06) to increase dietary NE. There was a quadratic effect of shade on longissimus area and marbling score, with values being lower (p<0.01) for LS_2.4 than for LS_1.2 or TS. Likewise, marbling score was lower for TS+F than for TS. Percentage kidney, pelvic, and heart (KPH) linearly decreased with increasing shade. In contrast, KPH was greater for TS than for TS+F. Conclusion: Providing more than 2.4 ㎡ shade/animal will not further enhance feedlot performance. The use of fans in combination with shade increases ADG and gain efficiency beyond that of shade, alone. These enhancements were not associated with increased DMI, but rather, to an amelioration of ambient temperature humidity index on maintenance energy requirement.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.46 no.3
• /
• pp.318-327
• /
• 2019

The purpose of this study was to identify which combination of zirconia crowns and cements is most similar in color to the maxillary primary incisors by varying the color of zirconia crowns, crown thickness, and shade of cements. Prefabricated zirconia crowns in 3 shades and crowns fabricated using 6 types of zirconia blocks were used in this study. These were filled with A2-shade or translucent-shade resin cement and the $L^*$, $a^*$, and $b^*$ values were calculated using a spectrophotometer. The color differences between the natural teeth and the zirconia crowns were assessed. The shade of the final restoration was more similar to that of the natural teeth using A2-shade than translucent-shade resin cement. Application of A2-shade cement to a 0.5-mm-thick crown fabricated from a smile series 2 zirconia block resulted in the color most similar to that of the natural teeth. A2-shade resin cement is recommended for zirconia crown restoration in anterior primary teeth compared to TR-shade resin cement for more esthetic restoration. Since restorations with Nu-smile zirconia crowns were not esthetically favorable in terms of shade, improvement of the shade characteristics of the product or development of a new kind of zirconia crown is required.

• Restorative Dentistry and Endodontics
• /
• v.24 no.2
• /
• pp.299-309
• /
• 1999

The composite resin, due to its esthetic qualities, is considered the material of choice for restoration of anterior teeth. With respect to shade control, the direct-placement resin composites offer some distinct advantages over indirect restorative procedures. Visible-light-cured (VLC) composites allow dentists to match existing tooth shades or to create new shades and to evaluate them immediately at the time of restoration placement. Optimal intraoral color control can be achieved if optical changes occurring during application are minimized. An ideal VLC composite, then, would be one which is optically stable throughout the polymerization process. The shade guides of the resin composites are generally made of plastic, rather than the actual composite material, and do not accurately depict the true shade, translucency, or opacity of the resin composite after polymerization. So the numerous problems associated with these shade guides lead to varied and sometimes unpredictable results. The aim of this study was to assess the color changes of current resin composite restorative materials which occur as a result of the polymerization process and to compare the color differences between the shade guides provided with the products and the actual resin composites before- and after-polymerization. The results obtained from this investigation should provide the clinician with information which may aid in improved color match of esthetic restoration. Five light activated, resin-based materials (${\AE}$litefil, Amelogen Universal, Spectrum TPH VeridonFil-Photo, and Z100) and shade guides were used in this study. Three specimens of each material and shade combination were made. Each material was condensed inside a 1.5mm thick metal mold with 10mm diameter and pressed between glass plates. Each material was measured immediately before polymerization, and polymerized with Curing Light XL 3000 (3M Dental products, USA) visible light-activation unit for 60 seconds at each side. The specimens were then polished sequentially on wet sandpaper. Shade guides were ground with polishing stones and rubber points (Shofu) to a thickness of approximately 1.5mm. Color characteristics were performed with a spectrophotometer (CM-3500d, Minolta Co., LTD). A computer-controlled spectrophotometer was used to determine CIELAB coordinates ($L^*$, $a^*$ and $b^*$) of each specimen and shade guide. The CIELAB measurements made it possible to evaluate the amount of the color difference values (${\Delta}E{^*}ab$) of resin composites before the polymerization process and shade guides using the post-polishing color of the composite as a control, CIE standard D65 was used as the light source. The results were as follows. 1. Each of the resin composites evaluated showed significant color changes during light-curing process. All the resin composites evaluated except all the tested shades of 2100 showed unacceptable level of color changes (${\Delta}E{^*}ab$ greater than 3.3) between pre-polymerization and post-polishing state. 2. Color differences between most of the resin composites tested and their corresponding shade guides were acceptable but those between C2 shade of ${\AE}$litefil and IE shade of Amelogen Universal and their respective shade guides exceeded what is acceptable. 3. Comparison of the mean ${\Delta}E{^*}ab$ values of materials revealed that Z100 showed the least overall color change between pre-polymerization and post-polishing state followed by ${\AE}$litefil, VeridonFil-Photo, Spectrum TPH, and Amelogen Universal in the order of increasing change and Amelogen Universal. Spectrum TPH, 2100, VeridonFil-Photo and ${\AE}$litefil for the color differences between actual resin and shade guide. 4. In the clinical environment, the shade guide is the better choice than the shade of the actual resin before polymerization when matching colors. But, it is recommended that custom shade guides be made from resin material itself for better color matching.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.5
• /
• pp.587-598
• /
• 2005

Statement of problem: Ceramic restorations should be made of porcelain layers of different opacity, shade, and thickness in order to provide a natural appearance. Lithium disilicate glass-ceramic system has superior color reproducibility, because it uses the ceramic ingot which is similar to teeth shade and uses the staining technique and layering technique. However, staining technique has a fault of discoloration. Also, porcelain is divided core and dentin layer, it is not enough to study about the influence of porcelain layer thickness and shade on the shade of ceramic restorations. Purpose: The purpose of this study was to evaluate the influence of porcelain layer thickness and color on the final shade of ceramic restorations. Materials and method: The CIE $L^*a^*b^*$(CIELAB) values of 72 assembled specimens, each consisting of 3 discs (enamel porcelain 0.2 mm/dentin porcelain -1.2, 0.9, 0.7, 0.5 or 0.3 mm/ceramic core -0.3, 0.5, 0.7, 0.9 or 1.2 mm, diameter is 1.0 mm) were evaluated with a spectrophotometer (Model Chromaview 300, Spectron Tech Co, Korea) for the shade A1, A2, A3 and A4. Distilled water (refractive index: 1.7) was used to attain optical contact between the layers. White, white gray, and white brown backgrounds were used to assess the influence of the background on the final shade. And the mean color difference value$({\Delta}E)$ was calculated. Results and conclusion: The results obtained from this study were as follows. 1. There was a significant correlation between the thickness ratio of the ceramic core/dentin porcelain system and $L^*,\;a^*\;and\;b^*$ values when the total thickness of specimen combination was smaller than 1.4 mm(P<0.05). 2. The specimen which the ceramic core thickness was more than 0.7 mm had the best masking effect against background colors. 3. The mean color difference value$({\Delta}E)$ is smaller than 2 $({\Delta}E<2)$ when the ceramic core thickness was larger than 0.7 mm and the total thickness of specimen was more than 1.4 mm.

• Journal of Environmental Science International
• /
• v.13 no.6
• /
• pp.489-495
• /
• 2004

The purpose of this research is to apply GIS(Geographic Information System) for the road simulation and find some benefits analysis for the design processes. The northern Jeju island was selected as a case study. The 1/5,000 digital map and GIS technique were used for optimum road design of the island based on Arc View software. Using this software we can get an overlay map by combination of hill shade map, slope map, aspect map, and building buffer map. Based on the overlay map, we designed the optimum road line and performed three dimensional simulation. From the results, we found that the developed three dimensional road simulation technique using GIS technique that was very useful tool to estimate the reasonable road design before the real road construction works.

• Journal of Ecology and Environment
• /
• v.33 no.4
• /
• pp.299-306
• /
• 2010

The use of local seed provenance is often recommended in forest restoration. Early vigor is a combination of the performance of seed germination and emergence after planting. The ability of young Brant's oak plants to grow and develop after emergence and its dependence on local habitat conditions was investigated in this study. The effects of seed source and shade on early growing seedlings of Brant's oak (Quercus brantii L.) were determined in field measurements. Seeds of Quercus brantii L. were collected from 4 forest areas (seed sources) in southern Zagros (Provinces of Kohkilouyeh-Bouyer Ahmad and Fars) at altitudes of 850, 1,100, 1,500, 2,100 m a.s.l., and planted in a nursery constructed in southwestern Iran. According to a split-plot design consisting of four blocks, each containing two main treatment plots (no shading, partial shading), each main plot was sub-divided into four sub-plots (for elevations of 850, 1,100, 1,500 and 2,100 m). Results showed that shade treatments had significant effects on emergence percentage and rate, shoot length, shoot dry weight (SDW), root dry weight (RDW), leaf area (LA), and chlorophyll content. Ecological factors also had an effect on seed performance. Altitude of seed source had a very significant effect on root length, LA, SDW, and RDW. The seeds collected from 850 m a.s.l. elevation showed the highest performance, especially in leaf area, root length, shoot dry weight, and root dry weight. Our results showed that the altitude of 850 m a.s.l. was the best for collecting Brant's oak seeds.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.24 no.1
• /
• pp.71-77
• /
• 2014

In this paper, we propose an improved numeric character recognition method which can recognize numeric characters well under low-illuminated and shade-illuminated environment. The LN(Local Normalization) preprocessing method is used in order to enhance low-illuminated and shade-illuminated image quality. The reading area is detected using line segment information extracted from the illumination-normalized meter images, and then the three-phase procedures are performed for segmentation of numeric characters in the reading area. Finally, an efficient hybrid classifier is used to classify the segmented numeric characters. The proposed numeric character classifier is a combination of multi-layered feedforward neural network and template matching module. Robust heuristic rules are applied to classify the numeric characters. Experiments using meter image database were conducted. Meter image database was made using various kinds of meters under low-illuminated and shade-illuminated environment. The experimental results indicates the superiority of the proposed numeric character recognition method.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.20 no.5
• /
• pp.67-81
• /
• 2017

Because of lack of accurate understanding of the mechanism of urban heat island (UHI) phenomenon and lack of scientific discussion, it is hard to come up with effective measures to mitigate UHI phenomenon. This study systematically described the UHI and suggested the solutions using green-infrastructure (green-infra). The factors that control UHI are very diverse: radiant heat flux, latent heat flux, storage heat flux, and artificial heat flux, and the air temperature is formed by the combination effect of radiation, conduction and convection. Green-infra strategies can improve thermal environment by reducing radiant heat flux (the albedo effect, the shade effect), increasing latent heat flux (the evapotranspiration effect), and creating a wind path (cooling air flow). As a result of measurement, green-infra could reduce radiant heat flux as $270W/m^2$ due to shadow effect and produce $170W/m^2$ latent heat flux due to evaporation. Finally, green-infra can be applied differently on the macro(urban) scale and micro scale, therefore, we should plan and design green-infra after the target objects of structures are set.