• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.9-14
• /
• 2012

In this study, the profiles of asphalt pavements were measured using a lightweight profiler and depths of macrotexture were analyzed based on the measured profiles. Profiles on dense graded asphalt pavement, prorous asphalt pavement, stone mastic asphalt (SMA) pavement, and base layer measured, and depth of macrotexture were calculated and analyzed. Profiles on the pavement that happened as asphalt mixture segregation were measured and depths of macrotexture were analyzed. The results showed that the depths of macrotexture of asphalt pavement were effectively calculated using the measured profiles, and the depths of macrotexture for different asphalt pavements were analyzed. The pavement areas which have asphalt mixture segregation were detected based on analysis of macrotexture depths.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.61-61
• /
• 2009

This paper has been performed in order to figure out the reason of failure in T23 weldments used for boiler tube at 550 $^{\circ}C$. Defects such as cracks and cavities occurred in CGHAZ (coarse grain heat-affected-zone) and multi pass of weld metal, and these crack propagated along grain boundary. Microstructure evolution such as grain growth and carbide precipitation was investigated by optical microscope (OM), transmission electron microscope(TEM). Moreover, Auger electron spectroscope (AES) was employed in order to examine segregation along the grain boundaries. There is significant difference in grain size and precipitation distribution in the region where cracking took place. In addition, sulfur segregation was observed. Based on the results of this investigation, it has been possible to establish that this type of cracks were consistent with reheat cracking and creep damage. Selection of optimal filler metal, heat input, and PWHT temperature is required for prevention in order to avoid this type of cracking.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1993.11a
• /
• pp.3-3
• /
• 1993

In mechanical testing of W-Ni-Pe heavy alloys, the cracks nucleate at W/W interface and propagate through W/ Imatrix interface or through matrix phase together with the cleavage of W grains. The mechanical properties can therefore be improved by control of the interfacial strength and area. In this presentation, some experimental result and techniques on this subject will be reviewed and discussed. The hydrogen embrittlement caused by the hydrogen segregation at interfaces during sintering in an hydrogen atmosphere can be removed by an heat-treattnent in vacuum or in an inert atmosphere. The heat-treatment condition can be estimated by using a diffusion equation for a cylindrical shape. The mechanical properties, in particular the impact property, are degraded by the segregation of non-metallic impurities, such as Sand P. The degradation can be prevented by adding a fourth element, such as La or Ca, active with the non-metallic impurities. The cyclic heat-treatment at usual heat-treattnent tempemture causes the penetration of matrix between W/W grain boundaries and results in remarkable increase in impact energy. This is due to an increase in the area of ductile failure during the impact test. The instability of W/matrix interface casued by addition of Mo or Re can be controlled by using W powders of different size. The increase in the interfacial area in found to be related to the presence of non-equilibrium pure W gmins among W(Mo or Re) solid solution gmins.

• Journal of Korea Foundry Society
• /
• v.19 no.1
• /
• pp.47-53
• /
• 1999

Squeeze casting process has been used in the field of a commercial manufacturing method, in which metal is enforcedly solidified under pressure enough to prevent the cast defects such as either gas porosity or shrinkage defect. In this paper, to clarify the relationship between applied pressures and macro ${\cdot}$ microstructural behaviors in gravity and direct squeeze casts, specimens were cast by various squeezing pressures during solidification of 7000 series Al wrought alloy in the metal die designed specially. The applied pressures used in this study were 0, 25, 50, and 75 MPa. The microstructural morphologies of squeeze cast were more fine and dense with increasing the applied pressures, because of the greater solidification rate of billet resulting from the applied pressure. A normal segregation phenomenon of an increasing in amount of eutectics towards the center of the billet was observed for squeeze casts, whereas gravity cast showed an inverse segregation phenomenon of an increasing in amount of eutectics towards the edge in the billet. This change in segregation pattern which is normal or inverse is due to a higher radial temperature gradient and reduced time in the semi solid state for squeeze casting.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.6
• /
• pp.41-50
• /
• 2012

In general, it is critical that grout consistency permit the complete filling of void space without segregation of ingredients. Recently, the antiwashout agent is used on underwater grout materials for preventing the grout from the segregation in water. This study introduces a new type of antiwashout underwater and flowable grout material using viscous modifiers and its characteristics comparing with conventional grout materials in fresh and sea water. It is found that the antiwashout underwater grout both in fresh and sea water has enough strength and good resistance to segregation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.6 no.1
• /
• pp.19-31
• /
• 1996

To invetigate the impurity distribution in GaAs crystal grown by horizontal Bridgman method, we constructd the mathematical model describing heat transfer, mass transfer and fluid flow n transient growth of GaAs. Galerkin finite element method and implicit time integration were used to solve the equations and simulate the transient growth. The concentration distribution is similar to the case of diffusion controlled growth when Gr - 0. With the increase of Gr the concentration profile is distroted and the minimum solute concentration appears near the interface. As solidification prosceeds, interface deflection increases steadily and transverse segregation increases until mixing by flow becomes steady. The axial segregation increases with solidification. But, with high intensity of flow axial segregation becomes steady after short transient. At small and large Gr the result showed a good agreememt with the prediction Smith and Scheil.

• Development and Reproduction
• /
• v.21 no.4
• /
• pp.467-473
• /
• 2017

Ascidian embryos have become an important model for embryological studies, offering a simple example for mechanisms of cytoplasmic components segregation. It is a well-known example that the asymmetric segregation of mitochondria into muscle lineage cells occurs during ascidian embryogenesis. However, it is still unclear which signaling pathway is involved in this process. To obtain molecular markers for studying mechanisms involved in the asymmetric distribution of mitochondria, we have produced monoclonal antibodies, Mito-1, Mito-2 and Mito-3, that specifically recognize mitochondria-rich cytoplasm in cells of the ascidian Halocynthia roretzi embryos. These antibodies stained cytoplasm like reticular structure in epidermis cells, except for nuclei, at the early tailbud stage. Similar pattern was observed in vital staining of mitochondria with DiOC2, a fluorescent probe of mitochondria. Immunostaining with these antibodies showed that mitochondria are evenly distributed in the animal hemisphere blastomeres at cleavage stages, whereas not in the vegetal hemisphere blastomeres. Mitochondria were transferred to the presumptive muscle and nerve cord lineage cells of the marginal zone in the vegetal hemisphere more than to the presumptive mesenchyme, notochord and endoderm lineage of the central zone. Therefore, it is suggested that these antibodies will be useful markers for studying mechanisms involved in the polarized distribution of mitochondria during ascidian embryogenesis.

• Journal of Korea Foundry Society
• /
• v.25 no.6
• /
• pp.240-248
• /
• 2005

The rheocasting characteristics are strongly influenced by the microstructural morphology such as particle size, form factor and contiguity. In this study, the effect of structural morphology on fluid flow characteristics of A356 semi-solid alloy was investigated with a vacuum suction fluidity test. Semi-solid metal slurry was made by the mechanical stirring, the liquidus casting, and H-NCM to be analysed. H-NCM could obtain uniform and fine globular microstructures of 0.9 form factor and 55 ${\mu}m$ particle size. Inoculation was found to be effective for reducing particle size, however, for H-NCM it should be avoided due to the cause of increasing contiguity. The fluidity test indicated that the non-stirring method had higher fluidity and smaller liquid segregation in the same solid faction of 0.4 than the stirring method, for smaller particle size and higher form factor. It was observed that liquid segregation decreased as the particle size is smaller and form factor is higher. The results of die-casting experiment were a good agreement with those of fluidity test.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.649-652
• /
• 2005

It is reported that semi-solid forming process takes many advantages over the conventional forming process, such as long die lift, good mechanical properties and energy saves. Rheology material has a thixotropic, pseudo-plastic and shear-thinning characteristic. Therefore, general plastic or fluid dynamic analysis is not suitable for the behavior of rheology material. So it is difficult for a numerical simulation of the rheology process to be performed because complicated processes such as the filling to include the state of the free surface and solidification in the phase transformation must be considered. Moreover, it is important to predict the deformation behavior for optimization of net shape forging process with semi-solid materials and to control liquid segregation for mechanical properties of materials. In this study, so, molecular dynamics simulation was performed for the control of liquid segregation in compression experiment as a part of study on analysis of rheology forming process.

• Korean Journal of Breeding Science
• /
• v.40 no.3
• /
• pp.211-214
• /
• 2008

Haploid system by anther culture allows the development of homozygous lines when doubled. The response of anther culture to Basta (glufosinate) resistance was investigated on transgenic plants (cv. Anjungbyeo) in order to identify inheritance of bar gene associated with Basta. Most of the regenerated transgenic plants were sterile, and only a few plants produced viable seeds ($A_1$) in the greenhouse. The bar gene was analysis by PCR in basta resistant transgenic plant ($TA_0$). The transgenic seeds ($A_1$) were significantly germinated in Basta solution compared with non-transformed seeds. As a result of anther culture, in regenerated haploid plants, segregation ratio was 1:1 in five of eight cross combinations. In diploid plants, segregation ratio was 1:1 in seven of eight cross combinations. Although there was some differences in the cross combinations, most of the combinations had 1:1 segregation ratio which supports the theory. The difference may be a result of the small sample size or the difference of anther culture response caused by genotypic difference. Hence, when many cross combinations were anther-cultured the results would support the theory.